SS443A ETC
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 1
Technical content
.010 MAX R (2) GATE FLUSH TO .004 OVERFLUSH 5° MAX (2) 220 45°(2) PARTING 200 MAX OPERATE LEA ne a ee ee ee || 180 Y 160 ——_ MAX RELEASE 160#.002 > a eee MICRO SutTcH DATE CODE < (140 LISTING (YEAR,WEEK) 918 MAX A+ oO eT Q 2 oso Bl pees ; — pO /\\ +.005 ml ay — ree ——S i U 5.902.020 80 te -_ joffe-.0152.002 (3) pe ose002 (3) 40 rons — a wes ee ee ee ee | .050 (2) 20 MAGNETIC CHARACTERISTICS (2. eee) ee ee ee ee < OPERATE GAUSS MAXIMUM [ 215 | 190 |i80 | 180 [190 | 200 | —40° 0° 25° 85° 125° 150° Ns) OPERATE GAUSS MINIMUM [| iio [ tio [iio | 90 | 80 [65 | ° TEMPERATURE — ~C i rs) RELEASE GAUSS MINIMUM [so | so | 75 | 70 [| 60 | 55 | nM |e [DIFFERENTIAL GAUSS MINIMUM] 25 [| 25 [| 25 | i5 [| 10 [5 | Y Ie ELECTRICAL CHARACTERISTICS AT -40°C 10 150°C VeC=3,.8V 10 24 VOLTS (UNLESS OTHERWISE NOTED ¢ CHARACTERISTIC TEST CONDITIONS [MIN T TYP [T MAX T uNITS | ¥ SUPPLY VOLTAGE SUPPLY VOLTAGE [3.8 [| f 24) fT vy | >|: SUPPLY CURRENT Tec | B > 250 G, Vec=24, 1SINK=20 mA mA Fa -40 C < T « 150C ge OUTPUT SATURATION VOLTAGE B > 250 G, Vec=3.8V, ISINK=20 mA] [| [| .4 [| Vv | Fe] OUTPUT LEAKAGE CURRENT Bo< 0 G, Vout=24V, Vec=24V a =- RISE TIME Vec=12V, RL=1.6K, CL=20pf Po Tos Tis | usec | lat [FALL Time ET Veet 2v, RE=1.6K, CL=20pAf TST ts | uwsec | LEH ABSOLUTE MAXIMUM RATINGS #8\\.—“—s™SCSCSCCCCCCidCdS [| CHARACTERISTIC POWER SUPPLY [ Veco {| =1 J 25 [ votts|
3 OUTPUT VOLTAGE (OFF) VOLTS BLOCK DIAGRAM CURRENT SINKING OUTPUT
ngvisions [OUTPUT ON CURRENT [| TSINK [50 | mA Vg (+) OPERATING TEMPERATURE TRIGGER [ance | HALL CIRCUIT OUTPUT J [mMaGnetic Feux | NO LIMIT] OTT SENSOR AND 5 | (0) NH. AMPLIFIER — GROUND (-) (T| NOTES a Zi, THE MAGNETIC FLUX USED TO OPERATE THE SWITCH MUST BE IN THE DIRECTION 1: AND LOCATION SHOWN (THIS ASSUMES THE CONVENTION THAT THE DIRECTION OF — THE EXTERNAL FLUX OF A MAGNET IS FROM THE NORTH TO THE SOUTH POLE OF Tos THE MAGNET) ba! ZX THE MAGNETIC FIELD STRENGTH (GAUSS) REQUIRED TO CAUSE THE SWITCH TO oy CHANGE STATE (OPERATE AND RELEASE) WILL BE AS SPECIFIED IN THE MAGNETIC (To 4 CHARACTERISTICS. TO TEST THE SWITCH AGAINST THE SPECIFIED MAGNETIC pte CHARACTERISTICS, THE SWITCH MUST BE PLACED IN A UNIFORM MAGNETIC FIELD {T_T ZX ABSOLUTE MAXIMUM RATINGS ARE THE EXTREME LIMITS THAT THE DEVICE WILL THIRD ANGLE PROJECTION [|< WITHSTAND WITHOUT DAMAGE TO THE DEVICE. HOWEVER, THE ELECTRICAL AND fee | [To MAGNETIC CHARACTERISTICS ARE NOT GUARANTEED AS THE MAXIMUM LIMITS (ABOVE @ -e — RECOMMENDED OPERATING CONDITIONS) ARE APPROACHED, NOR WILL THE DEVICE (T_| NECESSARILY OPERATE AT ABSOLUTE MAXIMUM RATING — ZA\\_ DIMENSIONS NOTED ARE DUE TO TIE BAR REMOVAL OPERATION AND ARE UNLESS OTHERWISE SPECIFIED 5 VALID ONLY IN TIE BAR AREA LOCATED WITHIN .080 DIMENSION TOLERANCES ARE oa} }2 HALL ELEMENT LOCATION WITH INTEGRATED CIRCUIT PLACEMENT TOLERANCE ONE PLACE © (.0)—Ss« #030 qs PEN TeADS MUST BE ADEQUATELY SUPPORTED DURWIG. ANY FORMING Sreanine HONEYWELL. THIS DRAWING 1S NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF MICRO SWITCH. ee ee QE OPERATION TO ENSURE THAT THE LEADS ARE NOT STRESSED INSIDE THE PLASTIC CATALOG LISTING ; 1. SH 7 PCB WAVE SOLDERING GUIDELINES ARE AS FOLLOWS: MICRO SWITCH SOLID STATE SWITCH SS443A THREE PLACES (.000) +.005 a] |< 250° TO 260° C SOLDERING TEMPERATURE MASTER REDUCED|a Honeywell Division ANGLES + 2} |> 3 SECONDS MAXIMUM SOLDERING TIME ANS_Y14.5M~1982 APPLIES] eo, wo, coor ees a a