SRC419x 192-kHz Stereo Asynchronous Sample-Rate Converters datasheet (Rev. C)

Document overview

  • Manufacturer or author: Texas Instruments, Incorporated [SBFS022,C]
  • PDF pages: 46

Technical content

AES, S/PDIF Output TX+ TX /cb1 DIT4192 Product Folder Sample & Buy T echnical Documents Tools & Software Support & Community SRC4192,SRC4193 SBFS022C –JUNE 2003–REVISED OCTOBER 2015 SRC419x192-kHzStereoAsynchronousSample-RateConverters

1 Features 3 Description

The SRC4192 and SRC4193 devices are 1• Automatic Sensing of the Input-to-Output asynchronous, sample-rate converters designed forSampling Ratio professional and broadcast audio applications. The• Wide Input-to-Output Sampling Range: 16:1 to SRC4192 and SRC4193 devices combine a wide 1:16 input-to-output sampling ratio with outstanding dynamic range and ultra-low distortion. Input and• Supports Input and Output Sampling Rates Up to output serial ports support standard audio formats, as212 kHz well as a Time Division Multiplexed (TDM) mode.• Dynamic Range: 144 dB (–60-dbFS Input, BW = Flexible audio interfaces allow the SRC4192 and20 Hz to fS/2, A-Weighted) SRC4193 devices to connect to a wide range of

  • THD+N: –140 dB (0-dbFS Input, BW = 20 Hz to audio data converters, digital audio receivers and fS/2) transmitters, and digital signal processors.
  • Attenuates Sampling and Reference Clock Jitter The SRC4192 device is a standalone, pin-
  • High-Performance, Linear-Phase Digital Filtering programmed device, with control pins for mode, data format, mute, bypass, and low group-delay functions.with Stop Band Attenuation Greater than 140 dB The SRC4193 device is a software-controlled device• Flexible Audio Serial Ports: featuring a serial peripheral interface (SPI) port,– Master or Slave-Mode Operation which is utilized to program all functions through the – Supports I2S, Left-Justified, Right-Justified, internal control registers. and TDM Data Formats The SRC4192 and SRC4193 devices can operate – Supports 16, 18, 20, or 24-Bit Audio Data from a single 3.3-V power supply. A separate digital I/O supply (VIO) operates over the 1.65-V to 3.6-V– TDM Mode Allows Daisy-Chaining of up to supply range, allowing greater flexibility whenEight Devices interfacing to current and future generation signal• Supports 24-, 20-, 18-, or 16-Bit Input and Output processors and logic devices. Both devices areData: All Output Data is Dithered from the Internal available in a 28-pin SSOP package.28-Bit Data Path
  • Low Group Delay Option for Interpolation Filter Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM)• Direct Downsampling Option for Decimation Filter (SRC4193 Only) SRC4192 SSOP (28) 5.30 mm × 10.20 mm SRC4193• SPI Port Provides Access to Internal Control Registers (SRC4193 Only) (1) For all available packages, see the orderable addendum at the end of the data sheet.• Soft Mute Function
  • Bypass Mode Simplified Application Diagram
  • Programmable Digital Output Attenuation (SRC4193 Only); 256 Steps: 0 dB to –127.5 dB, 0.5-dB/step
  • Power Down Mode
  • Operates From a Single 3.3-V Power Supply
  • Small 28-Pin SSOP Package
  • Pin Compatible with the AD1896 (SRC4192 Only)

2 Applications

  • Digital Mixing Consoles
  • Digital Audio Workstations
  • Audio Distribution Systems
  • Broadcast Studio Equipment
  • High-End A/V Receivers
  • General Digital Audio Processing An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA.

SRC4192,SRC4193 SBFS022C –JUNE 2003–REVISED OCTOBER 2015 www.ti.com Table of Contents

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (September 2007) to Revision C Page

  • Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Changes from Revision A (July 2003) to Revision B Page

2 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Product Folder Links: SRC4192 SRC4193

SRC4192,SRC4193 www.ti.com SBFS022C –JUNE 2003–REVISED OCTOBER 2015

5 Pin Configuration and Functions

BCKI 5 5 I Input port bit clock I/O BCKO 25 25 O Output port bit clock I/O BYPAS 9 9 I ASRC bypass control input (Active High) CCLK — 27 I SPI port data clock input CDATA — 28 I SPI port serial data input CS — 26 I SPI port chip select input (Active Low) DGND 8, 21 8, 21 – Digital ground IFMT0 10 — I Input port data format control input IFMT1 11 — I Input port data format control input IFMT2 12 — I Input port data format control input LGRP 1 — I Low group delay control input (active high) LRCKI 6 6 I Input port left/right word clock I/O LRCKO 24 24 O Output port left/right word clock I/O MODE0 26 — I Serial port mode control input MODE1 27 — I Serial port mode control input MODE2 28 — I Serial port mode control input MUTE 14 14 I Output mute control input (active high) 2,3,10,11,12,NC 3 – No connection17,18,19 OFMT0 19 — I Output port data format control input OFMT1 18 — I Output port data format control input OWL0 17 — I Output port data word length control input OWL1 16 — I Output port data word length control input Input-to-output ratio flag output RATIO — 16 O Low output denotes output rate lower than input rate. High output denotes output rate higher than input rate. RCKI 2 1 I Reference Clock Input RDY 15 15 O ASRC Ready Status Output (Active Low) Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 3 Product Folder Links: SRC4192 SRC4193

SRC4192,SRC4193 SBFS022C –JUNE 2003–REVISED OCTOBER 2015 www.ti.com Pin Functions (continued) PIN I/O DESCRIPTION NAME SRC4192 SRC4193 RST 13 13 I Reset Input (Active Low) SDIN 4 4 I Audio Serial Data Input SDOUT 23 23 O Audio Serial Data Output TDMI 20 20 I TDM Data Input (Connect to DGND when not in use) VDD 22 22 I Digital Core Supply, 3.3 V VIO 7 7 I Digital I/O Supply, 1.65 V to VDD

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted) (1) MIN MAX UNIT VDD –0.3 4 Supply Voltage V VIO –0.3 4 Digital Input Voltage –0.3 4 Operating Temperature –45 85 °C Storage temperature, Tstg –65 150 °C (1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

6.2 ESD Ratings

Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±3000 V(ESD) Electrostatic discharge VCharged-device model (CDM), per JEDEC specification JESD22- ±1500C101(2) (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. (2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT VDD 3 3.3 3.6 Supply voltage VIO 1.8 V 1.65 1.8 1.95 V VIO 3.3 V 3 3.3 3.6 Operating temperature –45 85 °C

4 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Product Folder Links: SRC4192 SRC4193

SRC4192,SRC4193 www.ti.com SBFS022C –JUNE 2003–REVISED OCTOBER 2015

6.4 Thermal Information

THERMAL METRIC(1) UNITDB (SSOP)

28 PINS

RθJA Junction-to-ambient thermal resistance 78.6 °C/W RθJC(top) Junction-to-case (top) thermal resistance 38.1 °C/W RθJB Junction-to-board thermal resistance 39.3 °C/W ψJT Junction-to-top characterization parameter 7.1 °C/W ψJB Junction-to-board characterization parameter 38.9 °C/W RθJC(bot) Junction-to-case (bottom) thermal resistance N/A °C/W (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953.

6.5 Electrical Characteristics

All parameters specified with TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DYNAMIC PERFORMANCE(1) Resolution 24 Bits fSIN Input sampling frequency 4 212 kHz fSOUT Output sampling frequency 4 212 kHz Upsampling 1:16 Input: output sampling ratio Downsampling 16:1 44.1 kHz; 48 kHz 140 48 kHz; 44.1 kHz 140 48 kHz; 96 kHz 140 44.1 kHz; 192 kHz 138 BW = 20 Hz to fSOUT/2, –60-dBFS Input96 kHz; 48 kHz 141 Dynamic range fIN = 1 kHz, Unweighted (add 3 dB to spec for A- dB 192 kHz; 12 kHz 141weighted result) 192 kHz; 32 kHz 141 192 kHz; 48 kHz 141 32 kHz; 48 kHz 140 12 kHz; 192 kHz 138 44.1 kHz; 48 kHz –140 48 kHz; 44.1 kHz –140 48 kHz; 96 kHz –140 44.1 kHz; 192 kHz –137 96 kHz; 48 kHz –140Total harmonic distortion + BW = 20 Hz to fSOUT/2, 0-dBFS Input fIN = 1 kHz, dBnoise Unweighted192 kHz; 12 kHz –140 192 kHz; 32 kHz –141 192 kHz; 48 kHz –141 32 kHz; 48 kHz –140 12 kHz; 192 kHz –137 Interchannel gain mismatch 0 dB Interchannel phase deviation 0 ° Minimum 0 Digital attenuation Maximum SRC4193 Only –127.5 dB Step Size 0.5 Mute attenuation 24-Bit Word Length, A-weighted –144 dB DIGITAL INTERPOLATION FILTER CHARACTERISTICS Passband 0.4535 × fSIN Hz Passband ripple ±0.007 dB Transition band 0.4535 × fSIN 0.5465 × fSIN Hz Stop band 0.5465 × fSIN Hz Stop band attenuation –144 dB (1) Dynamic performance measured with an Audio Precision System Two Cascade or Cascade Plus. Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 5 Product Folder Links: SRC4192 SRC4193

SRC4192,SRC4193 SBFS022C –JUNE 2003–REVISED OCTOBER 2015 www.ti.com Electrical Characteristics (continued) All parameters specified with TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Decimation Filter On (DFLT = 0) 102.53125/fSIN Normal group delay (LGRP = 0) s Decimation Filter Off (DFLT = 1) 102/fSIN Decimation Filter On (DFLT = 0) 70.53125/fSIN Low group delay (LGRP = 1) s Decimation Filter Off (DFLT = 1) 70/fSIN DIGITAL DECIMATION FILTER CHARACTERISTICS Passband 0.4535 × fSOUT Hz Passband ripple ±0.008 dB Transition band 0.4535 × fSOUT 0.5465 × fSOUT Hz Stop band 0.5465 × fSOUT Hz Stop band attenuation –143 dB Group delay – decimation filter DFLT = 0 for SRC4193 36.46875/fSOUT s Direct downsampling SRC4193 only, DFLT = 1 0 s DIGITAL I/O CHARACTERISTICS VIH High-level input voltage 0.7 × VIO VIO V VIL Low-level input voltage 0 0.3 × VIO V IIH High-level input current 0.5 10 µA IIL Low-level input current 0.5 10 µA VOH High-level output voltage IO = –4 mA 0.8 × VIO VIO V VOL Low-level output voltage IO = +4 mA 0 0.2 × VIO V CIN Input Capacitance 3 pF POWER SUPPLIES Operating voltage, VDD 3 3.3 3.6 V Operating voltage, VIO 1.65 3.3 3.6 VDD = 3.3 V, VIO = 3.3 V, RST = 0, No Clocks 100 µA Supply current, IDD, power down SRC4193 only, VDD = 3.3 V, VIO = 3.3 V, 5 mAPDN Bit = 0, No Clocks Supply current, IDD, dynamic VDD = 3.3 V, VIO = 3.3 V, fSIN = fSOUT = 192 kHz 66 mA VDD = 3.3 V, VIO = 3.3 V, RST = 0, No Clocks 100 Supply current, IIO, power down µASRC4193 only, VDD = 3.3 V, VIO = 3.3 V, 21PDN Bit = 0, No Clocks Supply current, IIO, dynamic VDD = 3.3 V, VIO = 3.3 V, fSIN = fSOUT = 192 kHz 2 mA VDD = 3.3 V, VIO = 3.3 V, RST = 0, No Clocks 660 µW Total power dissipation, PD, power down SRC4193 only, VDD = 3.3 V, VIO = 3.3 V, 16.6 mWPDN Bit = 0, No Clocks Total power dissipation, PD, dynamic VDD = 3.3 V, VIO = 3.3 V, fSIN = fSOUT = 192 kHz 225 mW

6.6 Switching Characteristics

over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT REFERENCE CLOCK TIMING fSMIN = min (fSIN, fSOUT), 128 ×RCKI frequency 50 MHzfSMAX = max (fSIN, fSOUT) fSMIN 1/(128tRCKIP RCKI period 20 ns×fSMIN) 0.4 ×tRCKIH RCKI pulsewidth high nstRCKIP 0.4 ×tRCKIL RCKI pulsewidth low nstRCKIP RESET TIMING tRSTL RST pulse width low 500 ns Delay following RST rising edge SRC4193 only 500 µs INPUT SERIAL PORT TIMING tLRIS LRCKI to BCKI setup time 10 ns tSIH BCKI pulsewidth high 10 ns

6 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Product Folder Links: SRC4192 SRC4193

6.7 Typical Characteristics

At TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. Figure 1. FFT With 1-kHz Input Tone at 0 dBFS Figure 2. FFT With 1-kHz Input Tone at –60 dBFS

At TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. Figure 3. FFT With 1-kHz Input Tone at 0 dBFS Figure 4. FFT With 1-kHz Input Tone at –60 dBFS Figure 5. FFT With 1-kHz Input Tone at 0 dBFS Figure 6. FFT With 1-kHz Input Tone at –60 dBFS Figure 7. FFT With 1-kHz Input Tone at 0 dBFS Figure 8. FFT With 1-kHz Input Tone at –60 dBFS

8 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

At TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. Figure 15. FFT With 1-kHz Input Tone at 0 dBFS Figure 16. FFT With 1-kHz Input Tone at –60 dBFS Figure 17. FFT With 1-kHz Input Tone at 0 dBFS Figure 18. FFT With 1-kHz Input Tone at –60 dBFS Figure 19. FFT With 1-kHz Input Tone at 0 dBFS Figure 20. FFT With 1-kHz Input Tone at –60 dBFS

10 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

At TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. Figure 27. FFT With 1-kHz Input Tone at 0 dBFS Figure 28. FFT With 1-kHz Input Tone at –60 dBFS Figure 29. FFT With 1-kHz Input Tone at 0 dBFS Figure 30. FFT With 1-kHz Input Tone at –60 dBFS Figure 31. FFT With 1-kHz Input Tone at 0 dBFS Figure 32. FFT With 1-kHz Input Tone at –60 dBFS

12 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

At TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. Figure 39. THD+N vs Input Amplitude fIN = 1 kHz Figure 40. THD+N vs Input Amplitude fIN = 1 kHz Figure 41. THD+N vs Input Amplitude fIN = 1 kHz Figure 42. THD+N vs Input Amplitude fIN = 1 kHz Figure 43. THD+N vs Input Amplitude fIN = 1 kHz Figure 44. THD+N vs Input Amplitude fIN = 1 kHz

14 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

At TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. Figure 51. Linearity With fIN = 200 Hz Figure 52. Linearity With fIN = 200 Hz Figure 53. Linearity With fIN = 200 Hz Figure 54. Linearity With fIN = 200 Hz Figure 55. Linearity With fIN = 200 Hz Figure 56. Frequency Response With 0-dBFS Input

16 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

At TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V, unless otherwise noted. Figure 57. Pass Band Ripple Figure 58. Pass Band Ripple

SRC4192,SRC4193 SBFS022C –JUNE 2003–REVISED OCTOBER 2015 www.ti.com

7 Detailed Description

7.1 Overview

The SRC4192 and SRC4193 devices are asynchronous, sample-rate converters (ASRC) designed for professional audio applications. Operation at input and output sampling frequencies up to 212 kHz is supported, with an input and output sampling ratio range of 16:1 to 1:16. Excellent dynamic range and Total Harmonic Distortion + Noise (THD+N) are achieved by employing high-performance, linear-phase digital filtering with image rejection better than 140 dB. Digital filtering options allow for lower group-delay processing. These include a low group-delay option for the interpolation and resampler function, as well as a direct down-sampling option for the decimation function (SRC4193 device only). The audio input and output ports support standard audio data formats, as well as a TDM interface mode. Word lengths of 24-, 20-, 18-, and 16-bits are supported. Both ports may operate in slave mode, deriving their word and bit clocks from external input and output devices. Alternatively, one port may operate in master mode while the other remains in slave mode. In master mode, the LRCK and BCK clocks are derived from the reference clock input, RCKI. The flexible configuration of the input and output ports allows connection to a wide variety of audio data converters, interface devices, digital signal processors, and programmable logic. A bypass mode is included, which allows audio data to be passed directly from the input port to the output port, bypassing the ASRC function. The bypass option is useful for passing through encoded or compressed audio data, or nonaudio control or status data. A soft mute function is available on both the SRC4192 and SRC4193 devices. Digital output attenuation is available only for the SRC4193 device. Both soft mute and digital attenuation functions provide artifact-free operation, while allowing muting or level adjustment of the audio output signal. The mute attenuation is typically –144 dB, while the digital attenuation control is adjustable from 0 dB to –127.5 dB in 0.5-dB steps. The SRC4193 device includes a three-wire SPI port to access on-chip control registers for configuration of internal functions. The port can be easily interfaced to microprocessors or digital signal processors with synchronous serial port peripherals. Functional Block Diagram shows a functional block diagram of the SRC4192 and SRC4193 devices. Audio data is received at the input port, clocked by either the audio data source in slave mode, or by the SRC419x in master mode. The output-port data is clocked by either the audio data source in slave mode, or by the SRC419x in master mode. The input data is passed through interpolation filters which up-sample the data, which is then passed on to the resampler. The rate estimator compares the input and output sampling frequencies by comparing LRCKI, LRCKO, and a reference clock. The results include an offset for the FIFO pointer and the coefficients needed for re-sampling function. The output of the resampler is passed on to either the decimation filter or direct down-sampler function. The decimation filter performs down-sampling and anti-alias filtering functions, and is required when the output sampling frequency is lower than the input-sampling frequency. The direct down-sampler function does not provide any filtering, and may be used in cases when aliasing is not an issue. This includes the case when the output sampling frequency is equal to or greater than the input sampling frequency. The advantage of direct down-sampling is a significant reduction in the group delay associated with the decimation filter, allowing lower latency sample rate conversion. The direct down-sampler function is available only for the SRC4193 device.

18 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Product Folder Links: SRC4192 SRC4193

MODE [2:0] IFMT [2:0 OFMT [1:0] OWL [1:0] MUTE BYPAS LGRP RST Control Logic (SRC4192) Rate Estimator LRCKI LRCKO REFCLK RDY RATIO (SRC4193 only) MUTE BYPASS RST CS CCLK CDA T A SPI and Control Logic (SRC4193) LRCKO BCKO SDOUT TDMI Audio Output Port Mux RCKI REFCLKReference Clock LRCKI BCKI SDIN Audio Input Port Interpolation Filters 16fSINfSIN fSOUT VDD DGND VIO DGND Re-Sampler 16fSOUT Decimation Filters fSOUT Direct Down-Sampler (SRC4193 only) Power SRC4192,SRC4193 www.ti.com SBFS022C –JUNE 2003–REVISED OCTOBER 2015

7.2 Functional Block Diagram

7.3 Feature Description

7.3.1 Input Port Operation

The audio input port is a three-wire synchronous serial interface that can operate in either slave or master mode. The SDIN input (pin 4) is the serial audio data input. Audio data is input at this pin in one of three standard audio data formats: Philips I2S, Left-Justified, or Right-Justified. The audio data word length may be up to 24-bits for I2S and Left-Justified formats, while the Right-Justified format supports 16-, 18-, 20-, or 24-bit data. The data formats are shown in Figure 59, while critical timing parameters are shown in Figure 60 and listed in Electrical Characteristics. Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 19 Product Folder Links: SRC4192 SRC4193

Figure 59. Input Data Formats Figure 60. Input Port Timing operates at a fixed rate of 64fS. sampling frequency. The LRCKI duty cycle is fixed to 50% for master mode operation. Control Register 3 are used to select the data format.

20 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Table 1. Input Port Data Format Selection

7.3.2 Output Port Operation

The audio output port is a four-wire synchronous serial interface that can operate in either Slave or Master mode. Figure 61. Output Data Formats

Figure 62. Output Port Timing regarding TDM mode operation is included in Application and Implementation. master mode. The LRCKO pulse width is fixed to 32 BCKO cycles for the TDM format in master mode. Table 2. Output Port Data Format Selection

7.3.3 Soft Mute Function

artifact-free muting of the audio output port.

7.3.4 Digital Attenuation (SRC4193 Only)

using Control Registers 4 and 5, corresponding to the left and right channels, respectively.

22 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Set CS = 1 here to write one register or buffer location. Keep CS = 0 to enable auto-increment mode. Byte 1: All 8 bits are Don’t Care. Set to 0 or 1. Bytes 2 through N: Register Data. All Bytes are written MSB first.

7.3.5 Ready Output

7.3.6 Ratio Output (SRC4193 Only)

an indicator or flag output for an LED or host device.

7.3.7 Serial Peripheral Interface (SPI) Port: SRC4193 Only

which are also listed in Electrical Characteristics. Figure 63. SPI Port Protocol Figure 64. SPI Port Timing

register addressed in Byte 0. program a single control register. Bringing the CS input high after the third byte will write just one register.

7.4 Device Functional Modes

7.4.1 Reset and Power Down Operation

shows the reset timing for the SRC419x device. the SPI port of the SRC4193 device. the control registers is maintained through the power-down and power-up transition. Figure 65. Reset Pulse Width Requirement

7.4.2 Audio Port Modes

device, the audio port mode is selected using the MODE0 (pin 26), MODE1 (pin 27), and MODE2 (pin 28) inputs. setting for the SRC4193 device is both input and output ports set to slave mode. reference clock input (RCKI). Only one port can be set to master mode at any given time, as indicated in Table 3. Table 3. Setting the Serial Port Modes

24 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Table 3. Setting the Serial Port Modes (continued)

7.4.3 Bypass Mode

Register 1. The BYPAS pin and control bit should be set to 0 for normal operation.

7.5 Register Maps

7.5.1 Control Register Map (SRC4193 Device Only)

Table 4. SRC4193 Device Control Register Map

1 PDN TRACK 0 MUTE BYPAS MODE2 MODE1 MODE0

3 OWL1 OWL0 OFMT1 OFMT0 0 IFMT2 IFMT1 IFMT0

4 AL7 AL6 AL5 AL4 AL3 AL2 AL1 AL0

5 AR7 AR6 AR5 AR4 AR3 AR2 AR1 AR0

7.5.1.1 System Control Register

Table 5. System Control Register Field Descriptions

7 PDN Power Down

6 TRACK Digital Attenuation Tracking

1 = Tracking On: Left channel attenuation setting is used for both channels.

5 Reserved

4 MUTE Output Soft Mute

3 BYPAS Bypass Mode

output port, bypassing the ARSC function.

7.5.1.2 Filter Control Register

Figure 66. Filter Control Register Table 6. Filter Control Register Field Descriptions

1 DFLT Decimation Filtering / Direct Down-Sampling

The DFLT bit enables or disables the direct down-sampling function.

0 LGRP Low Group Delay

buffer before the ASRC starts processing the audio data.

26 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

7.5.1.3 Audio Data Format Register

Figure 67. Audio Data Format Register Table 7. Audio Data Format Register Field Descriptions

3 Reserved

7.5.1.4 Digital Attenuation Register – Left Channel

Figure 68. Digital Attenuation Register – Left Channel Table 8. Digital Attenuation Register – Left Channel Field Descriptions 7-0 ALx Register defaults to 00HEX, or 0 dB (unity gain).

7.5.1.5 Digital Attenuation Register – Right Channel

Figure 69. Digital Attenuation Register – Right Channel Table 9. Digital Attenuation Register – Right Channel Field Descriptions 7-0 ARx Register defaults to 00HEX, or 0 dB (unity gain). for the Right Channel attenuation.

8 Application and Implementation

validate and test their design implementation to confirm system functionality.

8.1 Application Information

designing the SRC4192 and SRC4193 devices into the end equipment.

8.1.1 Interfacing to Digital Audio Receivers and Transmitters

transmitters to address these applications. SRC4193 device to be set to 3.3 V for interface compatibility. Figure 70. Interfacing the SRC4193 to the DIR1703 Digital Audio Interface Receiver device are set to 3.3 V for compatibility.

28 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

One Sub-Frame contains 64 bits, with 32 bits per channel. For each channel, the audio data is left justified, MSB first format, with the word length determined by the OWL[1:0] pins/bits. Figure 71. Interfacing the SRC4193 to the DIT4096/4192 Digital Audio Interface Transmitter device, to ensure that the transmitter is synchronized to the output port data of the SRC419x device.

8.1.2 TDM Applications

frame format, while Figure 73 shows TDM input timing parameters, which are listed in Electrical Characteristics. Figure 72. TDM Frame Format

Figure 73. Input Timing for TDM Mode

  • fBCKO = Output Port Bit Clock (BCKO), 27.648-MHz maximum
  • fs = Output Port Sampling (or LRCKO) Frequency, 216-kHz maximum. (1) This relationship holds true for both slave and master modes. Figure 74 and Figure 75 show typical connection schemes for TDM mode. Although the TMS320C671x DSP device family is shown as the audio processing engine in these figures, other TI digital signal processors with a multi-channel buffered serial port (McBSPTM) may also function with this arrangement. Interfacing to processors from other manufacturers is also possible. Refer to Figure 62 in this data sheet, along with the equivalent serial port timing diagrams shown in the DSP data sheet, to determine compatibility.

Figure 74. TDM Interface where all Devices are Slaves

30 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Figure 75. TDM Interface where one Device is Master to Multiple Slaves

8.2 Typical Application

be placed as close to the IC package as possible. Figure 76. Typical Connection Diagram for the SRC4192

Figure 77. Typical Connection Diagram for the SRC4193

8.2.1 Design Requirements

  • Control: Hardware, I2C, or SPI
  • Audio input: PCM serial data
  • Audio output: PCM serial data
  • Reference clock

8.2.2 Detailed Design Procedure

8.2.2.1 Control Method

communicate over a 3 wire SPI.

8.2.2.2 Audio Input and Output

or 1:16 is the max ratio supported between the input and output audio sampling rates.

32 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

8.2.3 Application Curves

Figure 78. FFT With 1-kHz Input Tone at 0 dBFS Figure 79. FFT With 1-kHz Input Tone at 0 dBFS

9 Power Supply Recommendations

the VIO and VDD supplies of the SRC4192 device must be set to 3.3 V.

10 Layout

10.1 Layout Guidelines

10.1.1 Reference Clock

clock input frequency is 50 MHz. Figure 80. Reference Clock Input Connections and Timing Requirements

SRC4192,SRC4193 SBFS022C –JUNE 2003–REVISED OCTOBER 2015 www.ti.com Layout Guidelines (continued)

10.1.2 Pin Compatibility With the Analog Devices AD1896 (SRC4192 Only)

The SRC4192 device is pin-and function-compatible with the AD1896 device when observing the guidelines indicated in the following paragraphs.

10.1.2.1 Crystal Oscillator

The SRC4192 does not have an on-chip crystal oscillator. An external reference clock is required at the RCKI input (pin 2).

10.1.2.2 Reference Clock Frequency

The reference clock input frequency for the SRC4192 must be no higher than 30 MHz, to match the master clock frequency specification of the AD1896 device. In addition, the SRC4192 device does not support the 768fS reference clock rate.

10.1.2.3 Master Mode Maximum Sampling Frequency

When the input or output ports are set to master mode, the maximum sampling frequency must be limited to 96 kHz to support the AD1896 device specification. This is despite the fact that the SRC4192 device supports a maximum sampling frequency of 212 kHz in master mode. The user should consider building an option into their design to support the higher sampling frequency of the SRC4192 device.

10.1.2.4 Matched Phase Mode

Because of the internal architecture of the SRC4192 device, it does not require or support the matched phase mode of the AD1896 device. Given multiple SRC4192 devices, if all reference clock (RCKI) inputs are driven from the same clock source, the devices will be phase-matched.

34 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

Product Folder Links: SRC4192 SRC4193

10.2 Layout Example

lower main PCB-ground plane with multiple vias. Figure 81. SRC4192 Layout Example

lower main PCB-ground plane with multiple vias. Figure 82. SRC4193 Layout Example

36 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated

11 Device and Documentation Support

11.1 Documentation Support

11.1.1 Related Documentation

11.2 Related Links

resources, tools and software, and quick access to sample or buy. Table 10. Related Links

11.3 Community Resources

solve problems with fellow engineers. contact information for technical support.

11.4 Trademarks

E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners.

11.5 Electrostatic Discharge Caution

during storage or handling to prevent electrostatic damage to the MOS gates.

11.6 Glossary

This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

www.ti.com 10-Nov-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) SRC4192IDB Active Production SSOP (DB) | 28 50 | TUBE Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4192I SRC4192IDB.A Active Production SSOP (DB) | 28 50 | TUBE Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4192I SRC4192IDBR Active Production SSOP (DB) | 28 2000 | LARGE T&R Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4192I SRC4192IDBR.A Active Production SSOP (DB) | 28 2000 | LARGE T&R Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4192I SRC4192IDBRG4 Active Production SSOP (DB) | 28 2000 | LARGE T&R Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4192I SRC4193IDB Active Production SSOP (DB) | 28 50 | TUBE Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4193I SRC4193IDB.A Active Production SSOP (DB) | 28 50 | TUBE Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4193I SRC4193IDBR Active Production SSOP (DB) | 28 2000 | LARGE T&R Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4193I SRC4193IDBR.A Active Production SSOP (DB) | 28 2000 | LARGE T&R Yes NIPDAU Level-1-260C-UNLIM -40 to 85 SRC4193I (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative Addendum-Page 1

www.ti.com 10-Nov-2025 and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 22-Aug-2026 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION www.ti.com 22-Aug-2026 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SRC4192IDBR SSOP DB 28 2000 350.0 350.0 43.0 SRC4193IDBR SSOP DB 28 2000 350.0 350.0 43.0 Pack Materials-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 22-Aug-2026 TUBE L - Tube length T - Tube height W - Tube width B - Alignment groove width *All dimensions are nominal Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm) SRC4192IDB DB SSOP 28 50 530 10.5 4000 4.1 SRC4192IDB DB SSOP 28 50 530 10.5 4000 4.1 SRC4192IDB.A DB SSOP 28 50 530 10.5 4000 4.1 SRC4192IDB.A DB SSOP 28 50 530 10.5 4000 4.1 SRC4192IDBR DB SSOP 28 2000 530 10.5 4000 4.1 SRC4192IDBR.A DB SSOP 28 2000 530 10.5 4000 4.1 SRC4192IDBRG4 DB SSOP 28 2000 530 10.5 4000 4.1 SRC4193IDB DB SSOP 28 50 530 10.5 4000 4.1 SRC4193IDB DB SSOP 28 50 530 10.5 4000 4.1 SRC4193IDB.A DB SSOP 28 50 530 10.5 4000 4.1 SRC4193IDB.A DB SSOP 28 50 530 10.5 4000 4.1 SRC4193IDBR DB SSOP 28 2000 530 10.5 4000 4.1 SRC4193IDBR.A DB SSOP 28 2000 530 10.5 4000 4.1 Pack Materials-Page 3

www.ti.com PACKAGE OUTLINE C 26X 0.65 8.45 28X 0.38 0.22 8.2

7.4 TYP

0.05 MIN

0.25 GAGE PLANE 0 -8

2 MAX

B 5.6 5.0 NOTE 4 A 10.5 9.9 NOTE 3 0.95 0.55 (0.15) TYP SSOP - 2 mm max heightDB0028A SMALL OUTLINE PACKAGE 4214853/B 03/2018

0.15 C A B

0.1 C NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side. 5. Reference JEDEC registration MO-150. A 15 DETAIL A TYPICAL SCALE 1.500

www.ti.com EXAMPLE BOARD LAYOUT

0.07 MAX

0.07 MIN

28X (1.85) 28X (0.45) 26X (0.65) (7) (R0.05) TYP SSOP - 2 mm max heightDB0028A SMALL OUTLINE PACKAGE 4214853/B 03/2018 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE: 10X SYMM SYMM 14 15 15.000 METALSOLDER MASK OPENING METAL UNDER SOLDER MASK SOLDER MASK OPENING EXPOSED METALEXPOSED METAL SOLDER MASK DETAILS NON-SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED

www.ti.com EXAMPLE STENCIL DESIGN 28X (1.85) 28X (0.45) 26X (0.65) (7) (R0.05) TYP SSOP - 2 mm max heightDB0028A SMALL OUTLINE PACKAGE 4214853/B 03/2018 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE: 10X SYMM SYMM 14 15

IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2026, Texas Instruments Incorporated Last updated 10/2025