SP4633 ZARLINK

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

This product is obsolete. This information is available for your convenience only. For more information on Zarlink’s obsolete products and replacement product lists, please visit http://products.zarlink.com/obsolete_products/

The SP4633 464 prescaler is one of GPS’ range of high speed dividers for consumer frequency synthesis and measurement systems. It has a low supply current, giving reduced dissipation and operating temperatures in an 8-pin plastic DIL package. Spurious radiation has been reduced from all stages. The SP4633 incorporates a two-stage preamplifier which gives good low frequency sensitivity and prevents self-oscillation.

FEATURES

■ Does Not Self Oscillate ■ Low Supply Current ■ Low Radiation ■ Input Wideband Amplifier ■ High Input Sensitivity ■ High Input Impedance ■ Balanced ECL Outputs ■ Electrostatic Protection † † ESD precautions must be observed SP4633 1GHz4464 NON SELF OSCILLATING PRESCALER Fig 1. Pin connections - top view DP8 3058-2.2 Fig. 2 SP4633 block diagram INPUT 15V1 OUTPUT SP4633 VCC DIFFERENTIAL INPUT OUTPUT 500 500 464 17V 2·5V p-p 255°C to 1150°C 0°C to180°C ABSOLUTE MAXIMUM RATINGS Supply voltage, VCC Input voltage Storage temperature Operating temperature range

ORDERING INFORMATION

ELECTRICAL CHARACTERISTICS

These characteristics are guaranteed over the following conditions (unless otherwise stated): TAMB = 0°C to 170°C, VCC = 4·5V to 5·5V (Test circuit see Fig. 3) 15V 180° HYBRID COUPLER 180 0·1 µ OUTPUT 180100n 100n 15p 15p A 50 Ω SIGNAL GENERATOR B C D 50 Ω SAMPLING SCOPE SP4633 Fig. 3 Test circuit 12p 15V 1n 180 0·1 µ OUTPUT 180100n 100n 15p 15p 100p

1 TURN

50Ω SOURCE Fig. 4 Application circuit SP4633 Characteristic Supply current, ICC Input sensitivity 50MHz to 400MHz 600MHz 800MHz 1000MHz Input overload Input impedance Output voltage, no load Output voltage with load as Fig. 3 Output impedance Output imbalance Conditions Value Typ. Max.Min. Units 7·5 mA mV mV mV mV mV Ω pF V p-p V p-p V V kΩ kΩ V 2,3 2,3 2,3 6,7 300 0·8 0·8 0·55 0·55 1·5 0·5 0·5 0·1 Pin V CC = 15V RMS sinewave (50Ω system) 50MHz to 1GHz operating frequency See Fig. 6 fIN = 1GHz, VCC = 15V NOTE The difference between the maximum input sensitivity and minimum overload voltage is the guaranteed dynamic range. Input signal levels should be maintained within these limits at all frequencies.

0 200 400 600 800 1000 1200 FREQUENCY (MHz) VIN (mV RMS INTO 50Ω ) TYPICAL DEVICE SPECIFICATION LIMIT Fig. 5 Typical input sensitivity j0.5 j0.2 2j0.2 2j0.5 2j1 2j2 10.50.2 2j5 2 5 1000 200 400600 800 Fig. 6 Typical input impedance (frequencies in MHz) S11 ZO = 50Ω

GEC PLESSEY SEMICONDUCTORS Cheney Manor, Swindon, Wiltshire SN2 2QW, United Kingdom. Tel: (0793) 518000 Fax: (0793) 518411 GEC PLESSEY SEMICONDUCTORS P.O. Box 660017

1500 Green Hills Road,

Scotts Valley, California 95067-0017, United States of America. Tel: (408) 438 2900 Fax: (408) 438 5576 CUSTOMER SERVICE CENTRES

  • FRANCE & BENELUX Les Ulis Cedex Tel: (1) 64 46 23 45 Tx: 602858F Fax : (1) 64 46 06 07
  • GERMANY Munich Tel: (089) 3609 06-0 Tx: 523980 Fax : (089) 3609 06-55
  • ITALY Milan Tel: (02) 66040867 Fax: (02) 66040993
  • JAPAN Tokyo Tel: (03) 3296-0281 Fax: (03) 3296-0228
  • NORTH AMERICA Integrated Circuits and Microwave Products Scotts Valley, USA Tel (408) 438 2900 Fax: (408) 438 7023. Hybrid Products, Farmingdale, USA Tel (516) 293 8686 Fax: (516) 293 0061.
  • SOUTH EAST ASIA Singapore Tel: (65) 3827708 Fax: (65) 3828872
  • SWEDEN Stockholm, Tel: 46 8 702 97 70 Fax: 46 8 640 47 36
  • UNITED KINGDOM & SCANDINAVIA Swindon Tel: (0793) 518510 Tx: 444410 Fax : (0793) 518582 These are supported by Agents and Distributors in major countries world-wide.  GEC Plessey Semiconductors 1993 Publication No. DS3058 Issue No. 2.2 May 1996 This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior knowledge the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request.