SLC ITT

Document overview

  • PDF pages: 16

Technical content

Page 1

Engineering Quick Reference Selection Guide

2 Position 4 Position 5 Position
Contact Arrangement Plug Receptacle 1 2 2 1 Contact Cannon Plug Receptacle 2 2 1 3 3 1 5 4 4 5
Features Inline Feed Thru Inline PCB Inline
Clip Lock Clip Lock Clip Lock Snap Lock Snap Lock
Specifications CS-216 CS-216 CS-216 CS-206 CS-206
Plug 086-0066-000 w/Wedgelock 086-0058-000 Standard 086-0058-000 Standard Contact Cannon 098532-0000 (5 A) 098532-001 (13 A) 098532-0000 (5 A) 098532-001 (13 A)
Receptacle 086-0061-000 w/Wedgelock 083-0242-000 Contact Cannon 098531-0000 (5 A) 098531-0001 (13 A) 098530-0000 (5 A) 098530-0001 (13 A)
Terminals See page 14 See page 14 Contact Cannon See page 14 See page 14

How to Order

SLC 5 T 13 0 0

PDF page 1 diagram

Series Prefix

Size/Configuration

Connector Type

Contact Termination

Material/Finish Modifier

Mechanical Modifier

Series Prefix

Contact Termination

SLC - Snap-Lock Circular

5 - 5 A 13 - 13 A

Size/Configuration

Material/Finish Modifier

5-5 Cavity Housing

0 -Standard Assembly (Silicone Elastomer)

8-8 Cavity Housing 10-10 Cavity Housing

1 -Fluorosilicone Elastomer

15-15 Cavity Housing

Mechanical Modifier

Connector Type

0 -Standard Assembly

P - Plug, In-line (Cable-to-Cable)\* R - Receptacle, In-line (Cable-to-Cable) T - Receptacle, Snap-thru B - Receptacle, PCB

\*Note: In-line Plug mates with all 3 receptacle types (In-line, Snap-thru, and PCB.)

Page 2

Engineering Quick Reference Selection Guide

Plug

Receptacle

8 Position 10 Position 15 Position
Receptacle Plug 1 2 2 1 7 8 3 3 7 6 4 8 5 4 5 6 Receptacle Plug 3 4 4 3 2 2 1 10 5 5 10 1 9 9 6 6 8 7 7 8 3 4 4 12 3 2 11 12 13 5 13 15 11 14 5 2 1 10 9 15 8 14 6 8 10 1 6 9 7 7
PCB Inline Snap-thru PCB Inline Snap-thru Snap-thru
Snap Lock (Double) Snap Lock (Double) Snap Lock (Double) Snap Lock (Double) Snap Lock (Double) Snap Lock (Double) Snap Lock (Double)
CS-210 CS-210 CS-210 CS-206 CS-206 CS-210 CS-210
098532-0010 098532-0008 098532-0010 098532-0002 (5 A) 098532-0003 (13 A) 098532-0002 (5 A) 098532-0003 (13 A) 098532-0002 (5 A) 098532-0003 (13 A) 086-0060-000
- - 098533-0010 098531-0002 (5 A) 098531-0003 (13 A) 098530-0002 (5 A) 098530-0003 (13 A) 098533-0002 098533-0003 086-0059-000
See page 14 See page 14 See page 14 See page 14 See page 14 See page 14 See page 14

Page 3

The Snap Lock Environmental Series is environmentally sealed connector created for printed

PDF page 3 diagram

circuit board, black box, cable-to-cable or bulkhead applications.

PDF page 3 diagram

When your under-the-hood requirements call for tough performance, the SLC "snaps" into a tightly sealed connection that can withstand heat, shock and vibration. The connector is designed to preserve the integrity of the solid state package, while protecting against contaminants - even when unmated.

Gold, tin/lead plated stamped contacts add durability.

PDF page 3 diagram

A rugged, thermoplastic receptacle body maximizes performance by withstanding temperature variances from -40°C to +150°C (material rating).

The SLC series is available in 2, 5, 8, 10, 15 contact cavity configurations. It can also be adapted to robotics assembly. Should you requirement demand higher density configurations, consult Customer Service.

Product Features and Benefits

  • Current rating 5 A and 13 A versions
  • Superior environmental sealing
  • Material rating: -40°C to +150°C continuous
  • Low millivolt drop
  • Low contact resistance

operation at rated current

  • Small footprint on P.C. board and low profile
  • Available in sizes 2, 5, 8, 10, 15 contacts
  • Adaptable to robotics assembly
  • Crimp stamped gold, tin/lead plated contacts
  • Hand insertable/removable contacts

Performance Specifications

Contact Resistance 10mΩ maximum Insulation Resistance 20MΩ minimum (USCAR) Current Rating 5 A signal continuous at 150°C all contacts, 2 position

  • Latch with tactile and audible feedback
  • Increases durability and provides for minimum installation
  • Low installed cost
  • Requires less PCB space

13 A power continuous at 150°C all contacts, 5 position and 10 position only

Dielectric Withstanding Voltage 1000 Vrms AC at sea level Applicable Cannon Specification SLC (CS-206) SLCT 5 & 10 (210) SLCT8 (216) SLCT 15 (206) Material Rating Operating Temperature -40°C to +150°C

Crimp Contacts Semi-automatic or hand crimpable or fully automatic Wire Size 20 - 16 AWG

Wire Insulation Sealing Range 1,98 (.078) to 3,30 (.130) dia. Contact Insertion No tool required. Suitable for automation. Contact Extraction Rear Removable Contact Retention 20 lbs. Minimum per contact Wire Strip Length 5,59 (.220) to 5,33 (.210)

Materials and Finishes

Connector Housing High temperature thermoplastic Contacts Copper alloy Finish Engaging area: Gold over nickel Crimp/P.C. tail area: Tin/lead over nickel - standard offering Tin/Lead over nickel - Option #2 all over

Environmental Seal High temperature silicone elastomer

Page 4

Contact Cavity Arrangements - Mating Face View

Plug

2

1 2

1

7

3

8 3 6

1 2

5 4

4 5

2 Way

5 Way

8 Way

PDF page 4 diagram

3 4 2 5 1 10 9 6 8 7

10 Way

Receptacle

2

2 1

3 1

3 7 8

2 1

4

4 5

6 5

2 Way

5 Way

8 Way

PDF page 4 diagram

3 4 2 1 5 10 9 6 8 7

10 Way

15 Way

Page 5

Plug, In-line\* (Cable-to-Cable) (Type P) SLC-5, SLC-10

PDF page 5 diagram
PDF page 5 diagram

Front-Face View 5 Cavity Housing

In-line Plug\* (Mates with SLC types R, T, and B) Housing Size Rating

Part Number

5

5 A

098532-0011

5

13 A

098532-0001

10

5 A

098532-0002

10

13 A

098532-0003

Side View

Front-Face View

Plug Assembly

10 Cavity Housing

Description

A

ØB

SLC-5P5-00

27,81 (1.095)

18,03 (.710)

SLC-5P13-00

26,80 (1.055)

18,03 (.710)

SLC-10P5-00

34,92 (1.375)

24,15 (.990)

SLC-10P13-00

34,04 (1.340)

25,15 (.990)

\*Contact lead assemblies are customer terminated and installed. See page 14, part numbers 110238-0488, 110238-2003.

Page 6

Receptacle, In-line\* (Cable-to-Cable) (Type R) SLC-5, SLC-10

PDF page 6 diagram
PDF page 6 diagram
PDF page 6 diagram

Front-Face View 5 Cavity Housing

In-line Receptacle\* (Mates with SLC type P) Housing Size Rating

Part Number

5

5 A

098530-0000

5

13 A

098530-0001

10

5 A

098530-0002

10

13 A

098530-0003

PDF page 6 diagram
PDF page 6 diagram

Side View

Front-Face View

Receptacle Assembly

10 Cavity Housing

Description

A

ØB C Ref.

SLC-5R5-00

24,13 (.950)

18,03 (.710) 24,38 (.960)

SLC-5R13-00

23,75 (.935)

18,03 (.710) 24,38 (.960)

SLC-10R5-00

31,24 (1.230)

25,15 (.990) 31,62 (1.245)

SLC-10R13-00

30,86 (1.215)

25,15 (.990) 31.62 (1.245)

\*Contact lead assemblies are customer terminated and installed. See page 16, part numbers 110238-0446, 110238-2004.

Square Flange

PDF page 6 diagram
PDF page 6 diagram

Materials and Finishes Material: Thermoplastic

Housing Size Part Number

A

Color: Black

5

066-9504.000 23,37 (.920)

PDF page 6 diagram

B Max.

ØC

31,24 (1.230)

32,51 - 31,75 (1.280 - 1.250)

066-9504-001 28,45 (1.120)

36,32 (1.430)

25,40 - 24,64 (1.000 - .970)

10

Page 7

Receptacle, Snap-thru\* (Type T) SLC-5, SLC-10

PDF page 7 diagram
PDF page 7 diagram
PDF page 7 diagram
PDF page 7 diagram

Side View

Front-Face View

Front-Face View

10 Position

5 Position

PDF page 7 diagram

Panel Section View

Snap-thru Receptacle\* (Mates with SLC Type P) Housing Size Rating

Part Number Description

5

5 A 098533-0000 SLC-5T5-00

5

13 A 098533-0001 SLC-5T13-00

10

5 A 098533-0002 SLC-10T5-00

10

13 A 098533-0003 SLC-10T13-00

Panel Rear Face View

ØA

ØB

ØC

ØD

37,21 (1.465) 24,13 (.950)

25,60 (1.008) 15,62 (.615)

36,96 (1.455) 23,75 (.935)

25,48 (1.003) 15,34 (.605)

47,62 (1.875) 31,24 (1.230) 35,05 (1.380) 20,19 (.795) 47,37 (1.865) 30,86 (1.215) 34,92 (1.375) 19,94 (.785)

\*Contact lead assemblies are customer terminated and installed. See page 14, part numbers 110238-0446, 110238-2004.

Page 8

Receptacle, PCB\* (Type B) SLC-5, SLC-10

PDF page 8 diagram
PDF page 8 diagram
PDF page 8 diagram

Front-Face View 5 Cavity Housing

In-line Receptacle\* (Mates with SLC Type P) Size Rating Part Number

Description

5 5 A 098531-0000 SLC-5B5-00

5 13 A 098531-0001 SLC-5B13-00 10 5 A 098531-0002 SLC-10B5-00

10 13 A 098531-0003 SLC-10B13-00 \*PCB Contacts are factory installed.

Recommended PCB Layout

PDF page 8 diagram
PDF page 8 diagram

Front-Face View

Side View

10 Cavity Housing

In-Line Receptacle With PCB Contacts

A ØB

C Ref.

24,13 (.950)

18,03 (.710)

24,38 (.960)

23,75 (.935)

18,03 (.710)

24,38 (.960)

31,24 (1.230) 25,15 (.990)

31,62 (1.245)

30,86 (1.215) 25,15 (.990)

31,62 (1.245)

PDF page 8 diagram
PDF page 8 diagram

Page 9

Receptacle, Snap-thru SLCT-8

Part No.: 098533-0010 (mates with 098532-0008)

PDF page 9 diagram
PDF page 9 diagram
PDF page 9 diagram
PDF page 9 diagram

Receptacle, Feed-thru CLC-2

Part No.: 086-0057-000

13,85

PDF page 9 diagram
PDF page 9 diagram

SEALED INTERFACE

Note: In-line plug and receptacle available.

Plug, Feed-thru CLC-2

PDF page 9 diagram

Part No.: 086-0058-000 With Silicone Grommet Seal Part No.: 086-0058-001 With Silicone Grommet Seal Part No.: 086-0058-002 With Fluorosilicone Seal

PDF page 9 diagram
PDF page 9 diagram

13,20 (.520)

A B

PDF page 9 diagram
PDF page 9 diagram

Right Angle CLC and CLC Y-Splice, please contact Product Management.

Page 10

Plug, Snap-thru SLC-15

PDF page 10 diagram

Part Number: 086-0060-000

PDF page 10 diagram
PDF page 10 diagram

Receptacle, Snap-thru SLC-15

PDF page 10 diagram

Part Number: 086-0059-000

PDF page 10 diagram
PDF page 10 diagram

Consult factory for alternate layouts.

Page 11

Contacts, Stamped, 5 and 13 Amp

Socket (use in plugs)

Hooded Socket

Pin (use in receptacles)

PDF page 11 diagram
PDF page 11 diagram

Reeled

Hooded Socket

Description

Socket Part Number

Pin Part Number

5 A

110238-1016 (030-2480-007)

110238-0446 (030-2464-007)

13 A

110238-2004 (030-2464-003)

Accessories

Sealing Plugs

PDF page 11 diagram

Socket Part Number

Number of Contacts

110238-0488 (030-2480-000)

4,500

110238-2003 (030-2480-003)

4,000

Connector Clip

PDF page 11 diagram
PDF page 11 diagram

Material: Thermoplastic, Color: Natural

Material: Thermoplastic, Color: Natural

Part Number: 225-0093-000

Part Number: 225-0093-000 +125°C Rating

+125°C Rating

Mounting Hardware for use on In-line Receptacle (Cable-to-Cable) (Type R) Fits Ø6,35 (.250) hole x 0,51 (.020) thick panel.

Page 12

Extraction Tool

Contact Extraction Tool Part Number: 274-7068-001 Tip Part Number: 323-9519-000

A Standard CET - SLE/SLC is available for extraction of the individual crimp contacts. Insertion tool is not required.

Insertion / Extraction Instructions for Crimp Contacts

PDF page 12 diagram

Insertion Tool No insertion tool is required. The contact is easily snapped in from the rear of the connector manually.

  1. Move to the rear of the connector so that the contact cavities can be identified.

Extraction

PDF page 12 diagram
PDF page 12 diagram
  1. Open the CET - SLC Extraction
  1. Using a straight motion forward,

tool and place it over the insulation

insert the tool along the wire until it

of the wire.

bottoms against the connector. (Do not use a screwing motion - damage will result.)

PDF page 12 diagram
PDF page 12 diagram
  1. Insert a crimp terminated
  1. Continue the forward movement

assembly into a selected cavity.

until and audible snap can be felt and heard. Slight pull in the opposite direction will confirm complete insertion.

PDF page 12 diagram
PDF page 12 diagram
  1. While the extraction tool is in
  1. Remove the extraction tool.

place, simply pull the wire/contact

Extraction is complete.

assembly out.

Page 13

Hand Crimp Tool Operation

PDF page 13 diagram

Hand Crimp Tool - CCT - SLC / SLE Part Number: 995-0002-232

The CCT-SLC/SLE hand crimp tool is designed to crimp individual SLC/SLE contacts on wire sizes 16, 18, and 20 AWG. Each cycle is ratchet-controlled (The tool must be completely closed before it can be reopened) to assure a satisfactory crimp each time. Over and under crimps are eliminated.

This tool is for use when the requirement is for low to moderate volume quantities, and for on-site applications where semiautomatic tools cannot be practically used.

PDF page 13 diagram
PDF page 13 diagram
  1. Cycle the CCT - SLE / SLC hand tool to the open
  1. While pressing upward on the locator spring, insert

position.

the contact with tails upward completely into the locator.

PDF page 13 diagram
PDF page 13 diagram
  1. Partially (usually the first click) Cycle the hand tool 5. Insert the pre-stripped wire into the crimp area of assuring that the upward thrusting tails of the contact the contact and completely cycle the tool. has started engaging with the top jaw of the tool. (There is a slight tendency for the contact to roll out of vertical alignment.)
PDF page 13 diagram
PDF page 13 diagram
  1. The result will be a perfect termination.
  1. Note that there are no unterminated wire strands, and that some strand ends can be seen at the forward edge of the crimp. Also note the insulation is gripped by the smaller secondary crimp. Distortion is at a minimum, both axially and laterally - no sharp edges.
PDF page 13 diagram
  1. When correctly positioned the contact should be located beyond flush with the edge of the CCT - SLE / SLC and positioned in the concave polished split level crimp.
PDF page 13 diagram
  1. While pressing upward on the locator spring withdraw the crimp termination.

Wire Stripping

5 and 13 A Contact

B

A

Tolerance

5,33 (.210)

2,41 (.095)

Low

5,59 (.220)

3,30 (.130)

High

Page 14

Lease Automatic Tooling - North America\*

ABT-607 Pneumatic Crimper

PDF page 14 diagram

The ABT-607 is a pneumatic powered and controlled machine. It is designed for customers with moderate volume. This machine is designed to semiautomatically crimp stamped and formed contacts onto pre-stripped stranded or single conductor electrical wire. This machine will accommodate size 34 thru 12 AWG wire and is actuated by the use of a foot pedal.

ABT-500 UCCD

The ABT-500 Universal Cannon Crimp Die, is a

PDF page 14 diagram

flywheel driven, electronically controlled machine that is designed to semi-automatically crimp stamped and formed contacts on stranded or single conductor, prestripped wire. This machine will accommodate size 34 thru 12 WG wire. The machine is actuated by the use of a foot pedal.

ABT-620 UCCS

The ABT-620 Universal Cannon Crimper/Stripper is a pneumatic powered, microprocessor controlled machine. It is designed to semi-automatically strip insulation from stranded or single conductor electrical wire and attach a stamped and formed contact by crimping. The machine will accommodate 34 thru 12 AWG wire. Primary application of the machine is the termination of jacketed cable where the individual leads cannot be stripped by fully automated equipment. The ABT-620 UCCS operates automatically upon insertion of a wire or it can be switched over to foot pedal operation if desired.

\* For other geographical regions, contact Cannon for details.

Machine Crimp Rate: 800 per hour

Power Requirements: Pneumatic = 100 psi, 2 cu. ft. per min.

Machine Crimp Rate: 1300 per hour

Power Requirements: Electrical = 115VAC, 60Hz, 20A

Machine Crimp Rate: 1200+ per hour

Power Requirements: Electrical = 115VAC, 60Hz, 20A Pneumatic = 80 psi, 3 cu. ft. per min.

Page 15

Crimp Pot Cross Section

PDF page 15 diagram

Crimp Height and Width

Wire Gauge (AWG)

CRIMP POT

18

20

16

CROSS SECTION

D Ref.

C\* D Ref.

C\* D Ref.

C\*

Signal (5A)

.064\*

.082

.056\* .080

.054\* .080

Power (13A)

.066\*

.082

.062\* .080

.058\* .080

The wire crimp heights listed are only

\* Hand Tools are ± .002 and machines are ± .001

reference and valid for the correspondingly listed wire size, wire plating and wire stranding.

The wire crimp tensile values must be used to assure the performance of

Insulation Height and Width

crimped contacts.

Wire Gauge (AWG)

18

20

16

For wire crimp information not listed in

Width

Height Width

Height Width

Height

this table, please contact Cannon.

Max

Max\*\*

Max Max\*\*

Max Max\*\*

Signal (5A)

.110

.115\*\*

.105 .110\*\*

.105 .110\*\*

Power (13A)

.110

.115\*\*

.105 .110\*\*

.105 .110\*\*

\*\* Measurements are taken without crimping wire insulation.

Crimp Tensile Strength

Wire Trim Dimension

(.220 - .210)

(.130 - .095)

20

18

16

Wire Size (AWG)

20lbs.

25 lbs.

35 lbs.

Tensile Min (lbs)

Page 16

Test Parameters

SLC Products are designed to meet Cannon specifications CS-206, CS-210, and CS-216. Items of most general interest to users are designers are listed below.

Test Description Reference Paragraph Requirements
Environmental Sealing 3.2.3.5 3.2.3.6 3.2.3.7 3.2.3.8 3.2.3.9 3.2.3.2 Sand and Dust MIL-STD-202 Method 110 Test Condition A 5% salt spray 96 hours 10 cycles of 24 hours, 90-98% humidity Steam Cleaning/Pressure Wash 95°C, 375 Cycles 750 PSIG Solvent Resistance/Immersion (see 3.2.3.9) Thermal Shock 100 Cycles -40°C to +150°C ± 3°C
Contact Crimp Tensile Strength 3.2.2.1 The minimum tensile load required to separate the wire from the contact, either by pulling the wire out of the crimp joint or by breaking the wire within the crimp joint shall not be less than the applicable limits as specified. Wire breakage or contact damage not due to crimping at less than tensile loads shall not constitute a failure. Wire Size AWG Crimp Tensile Strength, Pounds Minimum 16 35 18 25 20 20
Insulation Resistance 3.2.1.1 Mated and wired connectors shall exhibit an insulation resistance greater than 100 megohms between all contacts. This limit shall apply after exposure to each environment including salt solution immersion. Tests shall be performed at 100 VDC ± 10%.
Dielectric Withstanding Voltage 3.2.1.2 Wired and mated connectors shall show no evidence of breakdown between adjacent contacts when tested at 1000 VDC ± 5%. Connectors shall meet this requirement after exposure to each environment. Current leakage shall be less than 1.0 milliamp.
Low Level Contact Resistance 3.2.1.4 The low level contact resistance of mated contacts shall be less than 10 milliohms when measured across the contacts and crimp joints. The test current shall be a maximum of 100 milliamps with an open circuit test voltage of 20 millivolts maximum.
Mechanical Shock 3.2.3.3 Connectors shall be subjected to three shocks in each direction applied along the three mutually perpendicular axes of the connector test specimen for a total of 12 shocks. Each shock shall consist of a terminal peak sawtooth pulse with a peak value of 100 g's and a duration of 6 milliseconds.
Vibration 3.2.3.4 Connectors shall be subjected to random vibration in accordance with MIL-STD-1344, Method 2005.1, test condition VI for 20 hours along each of the following three axes: Direction Grms Radial axis of connector (Y) 10.2 Longitudinal axis of connector (Z) 10.2 Electrical continuity of the connectors shall be monitored during the last 20 minutes sweep in each axis with a test current of 100 milliamps or less and a test voltage less than 2VDC. Electrical discontinuities in excess of 10 microseconds shall be cause of failure.
Durability 3.2.2.6 Connectors shall be subjected to 25 cycles of mating and unmating at room temperature. Following this test there shall be no evidence of damage to the contacts, contact plating, connector housing or seals which may prove detrimental to reliable performance of the connector.
Contact 3.2.2.2 Contacts shall not be displaced greater than 0.030 inches from the connector body when a force of 10 pounds is applied. When this test follows maintenance again the same contacts shall be tested.
Maintenance Aging 3.2.2.3 Consist of subjecting each wired receptacle to 5 cycles of removal and reinsertion of 20% of the contacts or a minimum of 5 per connector with approved tooling.
Mating and Separating Force 3.2.2.4 The maximum force required to mate the plug and receptacle shall be 10 pounds. The maximum force required to separate the plug and receptacle shall be 5 pounds. The rate of travel shall be one inch per minute.
Solvent Resistance Immersion 3.2.2.9 Connectors shall be subjected to the following fluids at the temperature and length of time specified. Following the fluid dip or immersion, the connectors shall be immersed to a depth of 2 to 12 inches in a 5% salt-water solution for 24 hours at room temperature. At the completion of the salt-water immersion test, while still immersed, the connectors shall meet the insulation resistance requirement specified herein. Fluid Method Temperature No. 2 Diesel Fluid Immersion (2) 140°F Methyl Alcohol Dip (1) Room Temperature Antifreeze - Prestone Immersion (2) 180°F - 50% Water/50% Immersion (2) 180°F Ethylene Glycol Degreaser - Gunk Dip (1) Room Temperature - Mineral Spirits Dip (1) Room Temperature Paint (Oil Base) Immersion (2) Room Temperature Lubricating Oil Immersion (2) 200°F (SAE 10 W40) Brake Fluid Dip (1) Room Temperature (Delco Supreme) Transmission Fluid Dip (1) Room Temperature fully submerged and pressurized @ 7 psi. (Dextron) (1) Dip: Connectors shall withstand a one second dip and a three minute air dry for a total of 80 cycles. (2) Immersion: Connectors shall withstand immersion for one hour.
Temperature Life 3.2.3.1 Connectors shall be subjected to a temperature of 150°C ± 3°C for a period of 1000 hours. At the end of the temperature soak period and after removal from the chamber, the connectors shall meet the insulation resistance and dielectric withstanding voltage requirements specified herein. Connectors shall be operated at rated current throughout the duration of the temperature life test. Upon removal from the chamber at the conclusion of the test, the connectors shall show no visual signs of damage, which may be detrimental to the performance of the connector.
Thermal Cycling 3.2.3.2 Connectors shall be subjected to 100 thermal cycles from -40°C to +150°C. One cycle shall consist of the transitions from room temperature to -40°C to +150°C, and from 150°C to room temperature. One cycle shall be accomplished in a three-hour period with a minimum stabilization period of 15 minutes at each temperature extreme. The chamber temperature transition rate shall be a minimum of 1.30°C per minute and a maximum of 6.00°C per minute.
PDF page 16 diagram