SLA7062

SLA7062 ALLEGRO

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

28210.10 UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Combining low-power CMOS logic with high-current, high-voltage power FET outputs, the Series SLA7060M translator/drivers provide complete control and drive for a two-phase unipolar stepper motor with internal fixed off time and pulse-width modulation (PWM) control of the output current in a power multi-chip module (PMCM™). There are no phase-sequence tables, high-frequency control lines, or complex interfaces to program. The CMOS logic section provides the sequencing logic, direction, control, synchronous/asynchronous PWM operation, and a “sleep” function. The minimum CLOCK input is an ideal fit for applications where a complex µP is unavailable or overburdened. TTL or LSTTL may require the use of appropriate pull-up resistors to ensure a proper input-logic high. For PWM current control, the maximum output current is determined by the user’s selection of a reference voltage and sensing resistor. The NMOS outputs are capable of sinking up to 1, 2, or 3 A (depending on device) and withstanding 46 V in the off state. Clamp diodes provide protection against inductive transients. Special power-up sequencing is not required. Half-, quarter-, eighth-, and sixteenth-step operation are externally selectable for the SLA7060/61/62M. Half-step excitation alternates between the one-phase and two-phase modes (AB-B-AB-A-AB-B-AB- A), providing an eight-step sequence. The Series SLA7060M is supplied in a 21-pin single in-line power- tab package with leads formed for vertical mounting (suffix LF2102). The tab is at ground potential and needs no insulation. For high-current or high-frequency applications, external heat sinking may be required. This device is rated for continuous operation between -20°C and +85°C.

FEATURES

Internal Sequencer for Microstepping Operation PWM Constant-Current Motor Drive Cost-Effective, Multi-Chip Solution

100 V, Avalanche-Rated NMOS

Low rDS(on) NMOS Outputs Advanced, Improved Body Diodes Inputs Compatible with 3.3 V or 5 V Control Signals Sleep Mode Internal Clamp Diodes Always order by complete part number, e.g., SLA7060MLF2102 . ABSOLUTE MAXIMUM RATINGS Output Current, IO Logic Input Voltage Range, Reference Input Voltage Range, Package Power Dissipation, Operating Temperature Range, Storage Temperature Range, * Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified current rating or junction temperature. † Internal filtering provides protection against transients during the first 1 µs of the current-sense pulse. SLA7060M THRU SLA7062M PRELIMINARY INFORMATION (subject to change without notice) September 24, 2003

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000 SLA7060M THRU SLA7062M UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Functional block diagram Copyright © 2003 Allegro MicroSystems, Inc. Recommended operating conditions

www.allegromicro.com Electrical characteristics: unless otherwise noted at TA = +25°C, VBB = 24 V, VDD = 5.0 V. Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units Output drivers Driver Supply Volt. Range VBB Operating V Drain-Source Breakdown V(BR)DS VBB = 44 V, ID = 1 mA 100 V Output On Resistance rDS(on) SLA7060M, IO = 1.0 A 700 850 mΩ SLA7061M, IO = 2.0 A 250 400 mΩ SLA7062M, IO = 3.0 A 180 240 mΩ Body Diode Forward Volt. VF SLA7060M, IF = 1.0 A 0.85 1.1 V SLA7061M, IF = 2.0 A 0.95 TBD V SLA7062M, IF = 3.0 A 0.95 TBD V Driver Supply Current IBB mA VREF > 2.0 V (sleep mode) 100 µA Control logic Logic Supply Volt. Range VDD Operating 3.0 5.0 5.5 V Logic Input Voltage VIH 0.75VDD V VIL 0.25VDD V Logic Input Current IIH ±1.0 µA IIL CLOCK, RESET, CW/CCW, and SYNC. ±1.0 µA M1 and M2 -25 -50 -75 µA Max. Clock Frequency fclk 250* kHz PWM Off Time toff 70 to 100%Itripmax µs 38 to 64%Itripmax 9.0 µs 9 to 30%Itripmax 7.0 µs PWM Min. On Time ton(min) 1.8 µs Ref. Input Voltage Range VREF Operating 1.5 V Sleep mode 2.0 VDD V Ref. Input Current IREF ±10 µA Monitor Output Voltage VMoH VDD - 1.25 V VMoL 1.25 V Monitor Output Current IMo ±3.0 mA Sense Voltage VS Trip point at 100% IO 0.95VREF VREF 1.05VREF V Sense Input Current ISENSE ±10 µA Propagation Delay Time tPLH Clock rising edge to output on 2.0 µs tPHL Clock rising edge to output off 1.5 µs Logic Supply Current IDD 4.0 mA Typical values are given for circuit design information only. *Operation at a clock frequency greater than the specified minimum value is possible but not warranted.

Worcester, Massachusetts 01615-0036 (508) 853-5000 SLA7060M THRU SLA7062M UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Logic input timing

www.allegromicro.com Typical MOSFET characteristics TL [°C] TL [°C] TL [°C] SLA7060M SLA7061M SLA7062M

Worcester, Massachusetts 01615-0036 (508) 853-5000 SLA7060M THRU SLA7062M UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Typical body diode characteristics TL [°C] TL [°C] TL [°C] SLA7060M SLA7061M SLA7062M

input to the DACs and advances the motor one increment. take effect until the rising edge of the clock input. then re-enabled and the cycle repeats. step command to allow the internal circuitry to stabilize. Table 1. Step Modes

Table 2. Step Sequencing

• Home state; MO output high. † MO output high.

www.allegromicro.com Half-step output current waveshapes. For illustra- tive purposes, phase A\\ or B\\ current (unipolar drive) is shown as negative current. Quarter-step output current waveshapes. For illustrative purposes, phase A\\ or B\\ current (unipolar drive) is shown as negative current.

Worcester, Massachusetts 01615-0036 (508) 853-5000 SLA7060M THRU SLA7062M UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Eighth-step output current waveshapes. For illustrative purposes, phase A\\ or B\\ current (unipolar drive) is shown as negative current. Sixteenth-step output current waveshapes. For illustrative purposes, phase A\\ or B\\ current (unipolar drive) is shown as negative current.

www.allegromicro.com Applications information Layout. The printed wirting board should use a heavy ground plane. For optimum electrical and thermal performance, the driver should be soldered directly into the board. The driver supply terminal, VBB, should be decoupled with an electrolytic capacitor (>47 µF is recommended) placed as close to the device as possible. To avoid problems due to capacitive coupling of the high dv/dt switching transients, route the high-level, output traces away from the sensitive, low-level logic traces. Always drive the logic inputs with a low source impedance to increase noise immunity. Grounding. A star ground system located close to the driver is recommended. The logic supply return and the driver supply return should be connected together at only a single point — the star ground. Logic supply voltage, VDD. Transients at this terminal should be held to less than 0.5 V to avoid malfunctioning operation. Both VBB and VDD may be turned on or off separately. Logic inputs. Unused logic inputs (CW/CCW, M1, M2, RESET, or SYNC) must be connected to either ground or the logic supply voltage. Current sensing. To minimize inaccuracies caused by ground-trace IR drops in sensing the output current level, the current-sense resistors, RS, should have an independent ground return to the star ground of the device. This path should be as short as possible. For low-value sense resistors, the IR drops in the printed wiring board sense resistor’s traces can be significant and should be taken into account. The use of sockets should be avoided as they can introduce variation in RS due to their contact resistance. PWM current control. The maximum value of current limiting (ITRIP) is set by the selection of RS and the voltage at the REF input with a transconductance function ap- proximated by: ITRIP = VREF/RS The required VREF should not be less than 0.1 V. If it is, RS should be increased for a proportionate increase in VREF. Typical application RS = 0.1 Ω to 2 Ω R1 = 10 kΩ R2 = 5.1 kΩ R3 = 10 kΩ CA = 100 µF, 50 V CB = 10 µF, 10 V C1 = 0.1 µF

Worcester, Massachusetts 01615-0036 (508) 853-5000 SLA7060M THRU SLA7062M UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Applications Information (cont’d) Continuous Discontinuous mode mode Normalized FET on resistance Sync. signal generator Reference voltage. In the Typical Application shown, resistors R1 and R2 set the reference voltage as: VREF = (VDD x R2)/(R1 + R2) The trimming of R2 allows for the resistor tolerances and REF input current. The sum of R1+R2 should be less than 50 kΩ to minimize the effect of IREF. Minimum output current. The Series SLA7060M uses fixed off-time PWM current control. Due to internal logic and switching delays, the actual load current peak will be slightly higher than the calculated ITRIP value (especially for low-inductance loads). These delays, plus the mini- mum recommended VREF, limit the minimum value the current-control circuitry can regulate. An application with this device should maintain continuous PWM control in order to obtain optimum torque out of the motor. The boundary of the load current (IO(min)) between continuous and discontinuous operation is: IO(min) = [(VM + VSD)/Rm] x [(1/etoff/[Rm x Lm]) - 1] where VM = load supply voltage VF = body diode forward voltage Rm = motor winding resistance toff = PWM off time Lm = motor winding inductance To produce zero current in a motor, the REF input should be pulled above 2 V, turning off all drivers. Synchronous operation mode. If an external signal is not available to control the synchronous operation mode, a simple circuit can keep the SYNC input low while the CLOCK input is active; the SYNC input will go high (synchronous operation) when the CLOCK input stays low (“hold”). The RC time constant determines the sync trransition timing. NOTE –The use of this function except at 0, 70.7, or 100%Itripmax (half-step positions 0 through 8) is not recommended. Temperature effects on FET outputs. Analyzing safe, reliable operation includes a concern for the relation- ship of NMOS on resistance to junction temperature. Device package power calculations must include the increase in on resistance (producing higher on voltages) Io=0.5A Io=0.7A Io=1.0A 0.2 0.4 0.6 0.8 1.2 1.4 1.6 -50 -25 100 125 150 Junction temperature in C Vds(on) (V)

www.allegromicro.com Applications Information (cont’d) Allowable avalanche energy Waveforms during avalanche breakdown caused by increased operating junction temperatures. The figure provides a normalized on-resistance curve, and all thermal calculations should consider increases from the given +25°C limits, which may be caused by internal heating during normal operation. These power MOSFET outputs feature an excellent combination of fast switching, ruggedized device design, low on resistance, and cost effectiveness. Avalanche energy capability. There is a surge voltage expected when the output MOSFET turns off, and this voltage may exceed the MOSFET breakdown voltage (V(BR)DS). However, the MOSFETs are avalanche type and as long as the energy (E(AV)), which is imposed on the MOSFET by the surge voltage, is less than the maximum allowable value, it is considered to be within its safe operating area. Note that the maximum allowable ava- lanche energy is reduced as a function of temperature. In application, the avalanche energy (E(AV)) dissipated by the MOSFET is approximated as E(AV) = VDS(AV) x 0.5 x ID x t Output circuit for avalanche energy calculations Lead temperature TL [°C) at GND pin (#11) close to the package SLA7062M SLA7061M SLA7060M

Worcester, Massachusetts 01615-0036 (508) 853-5000 SLA7060M THRU SLA7062M UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Terminal list Terminal Pin Name Terminal Description 1, 2 OUTA Driver outputs for phase A 3, 4 OUTA\\ Driver outputs for phase A\\ SENSEA Phase A current sense VDD Logic power supply, VDD REF Current set & “sleep” control RESET Logic control input CW/CCW Forward/reverse logic control input CLOCK Step clock input GND Supply negative return Step mode logic control input Step mode logic control input MO Monitor logic output SYNC Synchronous PWM control input VBB Driver power supply, VBB SENSEB Phase B current sense 18, 19 OUTB\\ Driver outputs for phase B\\ 20, 21 OUTB Driver outputs for phase B The products described herein are manufactured in Japan by Sanken Electric Co., Ltd. for sale by Allegro MicroSystems, Inc. Sanken and Allegro reserve the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Therefore, the user is cautioned to verify that the information in this publication is current before placing any order. When using the products described herein, the applicability and suitability of such products for the intended purpose shall be reviewed at the users responsibility. Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to society due to device failure or malfunction. Sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Their use in any application requiring radiation hardness assurance (e.g., aerospace equipment) is not supported. When considering the use of Sanken products in applications where higher reliability is required (transportation equipment and its control systems or equipment, fire- or burglar-alarm systems, various safety devices, etc.), contact a Sanken sales representative to discuss and obtain written confirmation of your specifications. The use of Sanken products without the written consent of Sanken in applications where extremely high reliability is required (aerospace equipment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited. The information included herein is believed to be accurate and reliable. Application and operation examples described in this publication are given for reference only and Sanken and Allegro assume no responsibility for any infringement of industrial property rights, intellectual property rights, or any other rights of Sanken or Allegro or any third party that may result from its use.

www.allegromicro.com NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Recommended mounting hardware torque: 0.490 - 0.822 Nm. 4. Recommended use of metal-oxide-filled, alkyl-degenerated oil-base silicone grease: Dow Corning SC102, Toshiba YG6260, Shin-Etsu G746, or equivalent. SLA706xMLF2102 Dimensions in millimeters

Worcester, Massachusetts 01615-0036 (508) 853-5000 SLA7060M THRU SLA7062M UNIPOLAR STEPPER-MOTOR TRANSLATOR/DRIVERS Packing information 20 sticks/tubes in Y direction; 3 layers of sticks/tubes in Z direction = 1080 devices per box. 18 devices per stick/tube. A rubber stopper is provided at each end of the stick/tube.