Download PDFDATASHEET SEARCH SITE
Document overview
- PDF pages: 3
Technical content
Page 1
Low-profile with High Operation Force (Snap-in Type)
SKPE Series
High operation force best suitable for automotive use.
Detector
Push
Slide
Rotary
Encoders
Power
Dual-in-line Package Type
TACT Switch TM
Product Line
| Product No. | Operating force | Operating direction | Travel （mm） | Rating （max.） | Rating （min.） | Operating life （5mA 5V DC） | Initial contact resistance | Rubber color | Minimum order unit（pcs.） |
|---|---|---|---|---|---|---|---|---|---|
| SKPEADA010 | 1.18N | Vertical | 1.3 | 5mA 12V DC | 10BA 1V DC | 50,000cycles | 1kΩ max. | Light blue | 1,000 |
| SKPEAAA010 | 2.45N | Green | |||||||
| SKPEABA010 | 2.94N | Blue |
Custom- Products
Dimensions
Unit:mm
| Style | PC board mounting hole dimensions （Viewed from switch mounting face） |
| 6.6 2.5 6.3 Rubber dome 0.2 5 3.3 1 2 3.5 6.5 1 5.8 | 6.5 2-ø1.3 holes |
Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type
Note Using a 1.6mm thick PC board is recommended.
Refer to P.306 for soldering conditions.
Page 2
List of Varieties
Detector
Slide
Rotary
Encoders
Power
Dual-in-line Package Type
TACT Switch TM
Custom- Products
Sharp Feeling
Feeling Snap-in
Surface Mount Type Radial
D ：Depth. The most outer dimension excluding terminal portion. H ：Height. The minimum dimension if there are variances.
- TACT SwitchTM Soldering Conditions … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … 306
- TACT SwitchTM Cautions … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … 307
- Product Line of Knob for TACT SwitchTM… … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … 308
Page 3
Soldering Conditions
Condition for Reflow Available for Surface Mount Type. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA（K）or CC（T）at solder joints（copper foil surface）. A heat resistive tape
Detector
should be used to fix thermocouple.
- Temperature profile
Push
Temperature (˚C )
Slide
Rotary
180
Encoders
150
Power
Dual-in-line Package Type
TACT Switch TM
Custom- Products
Note 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended.
Sharp Feeling
Manual Soldering（Except SKRT Series）
Conditions for Auto-dip
Soft
| Items | Condition |
|---|---|
| Soldering temperature | 350℃max. |
| Duration of soldering | 3s max. |
| Capacity of soldering iron | 60W max. |
Available for Snap-in Type and Radial Type Feeling （Except SKHJ, SKHL, SKQJ, SKQK, SKEG series） Snap-in
| Items | Condition |
|---|---|
| Flux built-up | Mounting surface should not be exposed to fluk |
| Preheating temperature | Ambient temperature of the soldered surface of PC board. 100℃max. |
| Preheating time | 60s max. |
| Soldering temperature | 260℃max. |
| Duration of immersion | 5s max. |
| Number of soldering | 2times max. |
Type Surface Mount Type Radial Type
Notes 1. Consult with us for availability of TACT SwitchTM washing. 2. Prevent flux penetration from the top side of the TACT SwitchTM. 3. Switch terminals and a PC board should not be coated with flux prior to soldering. 4. The second soldering should be done after the switch is stable with normal temperature. 5. Use the flux with a specific gravity of min 0.81. （EC-19S-8 by TAMURA Corporation, or equivalents.）