SFF101 GWSEMI
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
10.0 AMP SUPER FAST RECTIFIERS
FEATURES
- Low forward voltage drop * High current capability * High reliability * High surge current capability * Good for switching mode application * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any VOLTAGE RANGE 50 to 600 Volts CURRENT
10.0 Amperes
Dimensions in inches and (millimeters) +PIN 1 PIN 2 CASE ITO-220A(FULLY INSULATED) .412 .248 .122 (3.1) .189 (4.8) .158 .610 .550 .100 (2.54) .060 .035 .108 (10.5) (6.3) (4.0) (15.5) (14.0)(1.5) (0.9) (2.75) MAX. MAX. MAX. MIN. MAX. MAX. 3.4 MAX. HOLE THRU f MAX. MAX. .114(2.9) .098(2.5) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current SFF101 SFF102 SFF103 SFF104 SFF105 SFF106 SFF107 UNITS 50 100 150 200 300 400 600 V 50 100 150 200 300 400 600 V 35 70 105 140 210 280 420 V at Tc=100 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 10.0A Maximum DC Reverse Current Tc=25 C at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) 10.0 125 500 -65 +150 A A nS PF NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 35 50 Operating and Storage Temperature Range TJ, TSTG C 3.0Typical Thermal Resistance R JC C/W V1.0 1.3 1.7 A A 116
0.1 1.0 .01 RATING AND CHARACTERISTIC CURVES (SFF101 THRU SFF107) FIG.3-TYPICAL FORWARD FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC CHARACTERISTICS FIG.2-TYPICAL FORWARD CURRENT AVERAGE FORWARD CURRENT,(A) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT FIG.6-TYPICAL JUNCTION CAPACITANCE REVERSE VOLTAGE,(V) JUNCTION CAPACITANCE,(pF) INSTANTANEOUS FORWARD CURRENT,(A) FORWARD VOLTAGE,(V) Pulse Width 300us 1% Duty Cycle 175 150 125 100 (+) (+) 25Vdc (approx.) ( ) ( ) NONINDUCTIVE NONINDUCTIVE W W PULSE GENERATOR (NOTE 2) OSCILLISCOPE (NOTE 1) NON- INDUCTIVE W NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. +0.5A -0.25A -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm trr .01 .05 .1 .5 1 5 10 50 100 D.U.T. 3.0 Single Phase Half Wave 60Hz Resistive Or Inductive Load DERATING CURVE SFF105~SFF106 SFF107 SFF101~SFF104 Tj=25 C 100 125 NUMBER OF CYCLES AT 60Hz 1 10 5 50 100 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 0 25 50 75 100 125 150 175 PEAK FORWARD SURGE CURRENT,(A) 0.1 1.0 .01 FIG.4-TYPICAL REVERSE CHARACTERISTICS 3.0 Tj=100 C Tj=25 C PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) 20 40 60 80 100 120 140 REVERSE LEAKAGE CURRENT, ( A) 117 CASE TEMPERATURE,( C)