S8380 HAMAMATSU

Document overview

  • PDF pages: 4

Technical content

Page 1

PDF page 1 diagram

S8380/S8381 series are designed to have higher sensitivity in the infrared and soft X-ray regions when compared to standard NMOS linear image sensors. The peak sensitivity wavelength is in the near IR region (λp=750 nm). The photodiodes of S8380 series have a height of 2.5 mm and are arrayed in a row at a spacing of 50 µm. The photodiodes of S8381 series also have a height of 2.5 mm but are arrayed at a spacing of 25 µm. The photodiodes are available in 3 different pixel quantities for each series, 128 (S8380-128Q), 256 (S8380-256Q, S8381-256Q) and 512 (S8380-512Q, S8381-512Q) and 1024 (S8381-1024Q). Quartz glass is the standard window material.

PDF page 1 diagram

25 µm (S8381 series) Pixel height: 2.5 mm l High UV sensitivity with good stability l Low dark current and high saturation charge allow a long integration time and a wide dynamic range at room temperature l Excellent output linearity and sensitivity spatial uniformity l Lower power consumption: 1 mW Max. l Start pulse and clock pulses are CMOS logic compatible Figure 1 Equivalent circuit

Figure 2 Active area structure

PDF page 1 diagram
PDF page 1 diagram
PDF page 1 diagram
Symbol Value
Vφ 15
P 1
Topr -40 to +65
Tstg -40 to +85
PDF page 1 diagram

Page 2

I Shape specifications

PDF page 2 diagram
PDF page 2 diagram
S8380-128Q S8380-256Q S8380-512Q S8381-256Q S8381-512Q S8381-1024Q
128 256 512 256 512 1024
31.75 40.6 31.75 40.6
22 22
Quartz Quartz
3.0 3.5 3.0 3.5

\*3: Fiber optic plate is available.

I Specifications (Ta=25 °C)

PDF page 2 diagram
PDF page 2 diagram
Symbol S8380 series S8381 series
Min. Typ. Max. Min. Typ. Max.
- - 50 - - 25 -
- - 2.5 - - 2.5 -
λ 200 to 1000 200 to 1000
λp - 750 - - 750 -
ID - 0.2 0.6 - 0.1 0.3
Cph - 20 - - 10 -
Esat - 90 - - 90 -
Qsat - 50 - - 25 -
PRNU - - ±3 - - ±3
PDF page 2 diagram
PDF page 2 diagram
PDF page 2 diagram
PDF page 2 diagram
PDF page 2 diagram

Page 3

PDF page 3 diagram

Page 4

I Recommended operating conditions

Terminal Input or output Description
φ1, φ2 (CM Input OS logic compatible) Pulses for operating the MOS shift register. The video data rate is equal to the clock pulse frequency since the video output signal is obtained synchronously with the rise of φ2 pulse.
φst (CM Input OS logic compatible) Pulse for starting the MOS shift register operation. The time interval between start pulses is equal to the signal accumulation time.
Vss - Connected to the anode of each photodiode. This should be grounded.
Vscg Input Used for restricting blooming. This should be grounded.
Vscd Input Used for restricting blooming. This should be biased at a voltage equal to the video bias voltage.
Active video Output Video output signal. Connects to photodiode cathodes when the address is on. A positive voltage should be applied to the video line in order to use photodiodes with a reverse voltage. When the amplitude of φ1 and φ2 is 5 V, a video bias voltage of 2 V is recommended.
Dummy video Output This has the same structure as the active video, but is not connected to photodiodes, so only spike noise is output. This should be biased at a voltage equal to the active video or left as an open-circuit when not needed.
Vsub - Connected to the silicon substrate. This should be grounded.
End of scan (CM Output OS logic compatible) This should be pulled up at 5 V by using a 10 kΩ resistor. This is a negative going pulse that appears synchronously with the φ2 timing right after the last photodiode is addressed.
NC - Should be grounded.

Figure 5 Spectral response (typical example)

(Ta=25 ˚C)

PDF page 4 diagram

WAVELENGTH (nm)

KMPDB0161EA

Figure 7 Timing chart for driver circuit

PDF page 4 diagram

V s (H) st V s (L) V 1 (H) 1 V 1 (L) V 2 (H) 2 V 2 (L)

ACTIVE VIDEO OUTPUT

END OF SCAN

Figure 6 Output charge vs. exposure

PDF page 4 diagram

EXPOSURE (lx · s)

KMPDB0162EB

Figure 8 Video bias voltage margin

PDF page 4 diagram

CLOCK PULSE AMPLITUDE (V)

KMPDB0043EA

Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2005 Hamamatsu Photonics K.K.

HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10

United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741

Cat. No. KMPD1045E01 Oct. 2005 DN