RM914 SKYWORKS

Document overview

  • PDF pages: 16

Technical content

Page 1

The RM914 Advanced Mobile Phone Service (AMPS) Power Amplifier is a fully matched 6-pin surface mount module designed for mobile units operating in the 824-849 MHz cellular bandwidth. This device can be driven to power output levels beyond 31 dBm for high efficiency FM mode operation. A single GaAs Microwave Monolithic Integrated Circuit (MMIC) contains all active circuitry in the module. The MMIC contains on-board bias circuitry as well as input and interstage matching circuits. The output match is realized off-chip and within the module package to optimize efficiency and power performance into a 50 Ω load. This device is manufactured with Skyworks’s GaAs HBT process that provides for all positive

voltage DC supply operation while maintaining high efficiency. Primary bias to the RM914 can be supplied directly from a three cell nickel-cadmium, single cell lithium-ion, or other suitable battery with output in the 3-4 volt range. Power down is accomplished by setting the voltage on the low current reference pin to zero volts. No external supply side switch is needed as typical “off” leakage is a few microamperes with full primary voltage supplied from the battery.

Functional Block Diagram

Distinguishing Features

  • Low voltage positive bias supply (3 to 4 Volts, typical)
  • High efficiency
  • Large dynamic range
  • 6-pin package (6mm x 6mm x 1.5 mm)
  • Power down control

Applications

  • Analog cellular (AMPS)
  • Wireless local loop (WLL)
PDF page 1 diagram

Data Sheet © 2001, 2002 Skyworks Solutions, Inc., All Rights Reserved.

Page 2

Electrical Specifications

Electrical Specifications

The following tables list the electrical characteristics of the RM914 Power Amplifier. Table 1 lists the absolute maximum rating for continuous operation. Table 2 lists the recommended operating

conditions for achieving the electrical performance listed in Table 3. Table 3 lists the electrical performance of the RM914 Power Amplifier over the recommended operating conditions.

Table 1. Absolute Maximum Ratings(1)

Parameter Symbol Minimum Nominal Maximum Unit
RF Input Power Pin — 3.0 6.0 dBm
Supply Voltage Vcc — 3.4 6.0 Volts
Reference Voltage Vref — 3.0 3.3 Volts
Case Operating Temperature Tc –30 25 +110 °C
Storage Temperature Tstg –55 — +125 °C
NOTE(S): No damage assuming only one parameter is set at limit at a time with all other parameters set at or below nominal value.

Table 2. Recommended Operating Conditions

Parameter Symbol Minimum Nominal Maximum Unit
Supply Voltage Vcc 3.2 3.4 4.2 Volts
Reference Voltage Vref 2.9 3.0 3.1 Volts
Operating Frequency Fo 824.0 836.5 849.0 MHz
Operating Temperature To –30 +25 +85 °C

Page 3

Electrical Specifications

Table 3. Electrical Specifications for AMPS Nominal Operating Conditions(1)

PDF page 3 diagram

Table 4. Electrical Specifications Limits for AMPS Recommended Operating Conditions(1)

PDF page 3 diagram

Page 4

Characterization Data

Characterization Data

The following charts illustrate the characteristics of a typical RM914 Power Amplifier tested in the evaluation board described in the following section. The amplifier was selected by characterizing a

group of devices and choosing a part with average electrical performance at both nominal and worst case (limit) conditions. Figures 1 through 2 illustrate the analog characteristics of the

RM914.

Figure 1. Analog Gain vs. Output Power

PDF page 4 diagram

Legend

824 MHz @ –30 °C

824 MHz @ +25 °C

824 MHz @ +85 °C

‹

‹

‹

837 MHz @ –30 °C

837 MHz @ +25 °C

837 MHz @ +85 °C

„

„

„

849 MHz @ –30 °C

849 MHz @ +25 °C

849 MHz @ +85 °C

Œ

Œ

Œ

Page 5

Characterization Data

Figure 2. Analog Power Added Efficiency vs. Output Power

PDF page 5 diagram

Figure 3. Analog Second Order Harmonic Suppression Magnitude

PDF page 5 diagram

Legend

824 MHz @ –30 °C

824 MHz @ +25 °C

824 MHz @ +85 °C

‹

‹

‹

837 MHz @ –30 °C

837 MHz @ +25 °C

837 MHz @ +85 °C

„

„

„

849 MHz @ –30 °C

849 MHz @ +25 °C

849 MHz @ +85 °C

Œ

Œ

Œ

Page 6

Characterization Data

Figure 4. Analog Third Order Harmonic Suppression Magnitude

PDF page 6 diagram

Legend

824 MHz @ –30 °C

824 MHz @ +25 °C

824 MHz @ +85 °C

‹

‹

‹

837 MHz @ –30 °C

837 MHz @ +25 °C

837 MHz @ +85 °C

„

„

„

849 MHz @ –30 °C

849 MHz @ +25 °C

849 MHz @ +85 °C

Œ

Œ

Œ

Page 7

Characterization Data

Figure 5. Analog Gain vs. Output Power

PDF page 7 diagram

Figure 6. Analog Second Harmonic Suppression Magnitude

PDF page 7 diagram

Page 8

Characterization Data

Figure 7. Analog Third Order Harmonic Suppression Magnitude

PDF page 8 diagram

Figure 8. Noise Figure Variation Over Recommended Operating Conditions

PDF page 8 diagram

Page 9

Characterization Data

Figure 9. Voltage Standing Wave Ratio Variation Over Recommended Operating Conditions

PDF page 9 diagram

Page 10

Evaluation Board Description

Evaluation Board Description

The evaluation board is a platform for testing and interfacing design circuitry. To accommodate the interface testing of the RM914, the evaluation board schematic and diagrams are included for preliminary analysis and design. Figure 10 shows the basic schematic of the board for the 824 MHz to 849 MHz range. Figure 11 illustrates the board layout.

Figure 10. Evaluation Board Schematic

PDF page 10 diagram

Figure 11. Evaluation Board Assembly Diagram

PDF page 10 diagram
PDF page 10 diagram
REF DESIGNATIONS VALUES QTY
C1 100 pF 1
C2 4.7 uF 1
C3 39 pF 1
C4 1000 pF 1

100637_004

Page 11

Package Dimensions and Pin Descriptions

Package Dimensions and Pin Descriptions

The RM914 is a multi-layer laminate base, overmold encapsulated modular package designed for surface mount solder attachment to a printed circuit board. Figure 12 is a mechanical drawing of

the pad layout for this package and Figure 13 illustrates typical case markings. The pin numbering convention starts with pin 1 in the upper left, as indicated in Figure 12, and increments

counter-clockwise around the package. Table 5 describes each pin function.

Figure 12. RM914 Package Drawing

PDF page 11 diagram

Page 12

Package Dimensions and Pin Descriptions

Table 5. Pin Description

Pin # Function
1 VCC1(1)
2 RF Input
3 VREF
4 VCC2(1)
5 RF Output
6 GND
7 GND(2)
NOTE(S): (1) All supply pins may be connected together at the supply. (2) Package underside is GND.

Figure 13. Typical Case Markings

PDF page 12 diagram

Page 13

Package and Handling Information

Package and Handling Information

Because of its sensitivity to moisture absorption, this device package is baked and vacuum packed prior to shipment. Instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly.

The RM914 is capable of withstanding an MSL 3/225 °C solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is attached in a reflow oven, the temperature ramp rate should not exceed 5 °C per second; maximum temperature should not exceed 225 °C. If the part is manually attached, precaution should be taken to insure that the part is not subjected to temperatures exceeding 225 °C for more than 10 seconds. For details on both attachment techniques, precautions, and handling procedures recommended by Conexant, please refer to Application Note: PCB Design and SMT

Assembly/Rework, Document Number 101752. Additional information on standard SMT reflow profiles can also be found in the JEDEC Standard J–STD–020A.

Production quantities of this product are shipped in the standard tape-and-reel format. For packaging details, refer to Application Note: Tape and Reel, Document Number 101568.

Page 14

Electrostatic Discharge Sensitivity

Electrostatic Discharge Sensitivity

The RM914 is a Class I device. Figure 14 lists the Electrostatic Discharge (ESD) immunity level for each pin of the RM914 product. The numbers in Figure 14 specify the ESD threshold level for each pin where the I-V curve between the pin and ground starts to show degradation. The ESD testing was performed in compliance with MIL-STD-883E Method 3015.7 using the Human Body Model. Since 2000 volts represents the maximum measurement limit of the test equipment used, pins marked > 2000 V pass 2000V ESD stress.

Figure 14. ESD Sensitivity Areas

PDF page 14 diagram

Various failure criteria can be utilized when performing ESD testing. Many vendors employ relaxed ESD failure standards which fail devices only after “the pin fails the electrical specification limits” or “the pin becomes completely non-functional”. Skyworks employs the most stringent criteria and fails devices as soon as the pin begins to show any degradation on a curve tracer. To avoid ESD damage, latent or visible, it is very important the Class-1 ESD handling precautions listed in Table 6 be used in the product assembly and test areas follow.

Table 6. Precautions for GaAs ICs with ESD Thresholds Greater Than 200V But Less Than 2000V

Personnel Grounding Wrist Straps Conductive Smocks, Gloves and Finger Cots Antistatic ID Badges Facility Relative Humidity Control and Air Ionizers Dissipative Floors (less than 109 Ω to GND)
Protective Workstation Dissipative Table Tops Protective Test Equipment (Properly Grounded) Grounded Tip Soldering Irons Conductive Solder Suckers Static Sensors Protective Packaging & Transportation Bags and Pouches (Faraday Shield) Protective Tote Boxes (Conductive Static Shielding) Protective Trays Grounded Carts Protective Work Order Holders

Page 15

Ordering Information

Model Number Manufacturing Part Number Product Revision Package Operating Temperature
RM914 RM914-13 13 6x6LM-6 –30 °C to +85 °C

Revision History

Revision Level Date Description
A September 2000 Initial Release
B December 2000 Add Solder Reflow, Temperature Guidelines Revised data Table 1, Table 4; Revised Figure 13
C August 2001 Revise: Table 3, Leakage Current.
D March 22, 2002 Revise: Tables 3 and 4. Add: Reference Documents

References

Application Note: Tape and Reel, Document Number 101568.

Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752

JEDEC Standard J–STD–020A

© 2002, Skyworks Solutions, Inc. All Rights Reserved.

Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products. These materials are provided by Skyworks as a service to its customers and may be used for informational purposes only. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its products, specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its products and product descriptions.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as may be provided in Skyworks' Terms and Conditions of Sale for such products, Skyworks assumes no liability whatsoever.

THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF SKYWORKS™ PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE

MATERIALS.

Skyworks™ products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks' customers using or selling Skyworks™ products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.

The following are trademarks of Skyworks Solutions, Inc.: Skyworks™, the Skyworks symbol, and "Breakthrough Simplicity"™. Product names or services listed in this publication are for identification purposes only, and may be trademarks of third parties. Thirdparty brands and names are the property of their respective owners.

Additional information, posted at www.skyworksinc.com, is incorporated by reference.

Page 16

PDF page 16 diagram

General Information: Skyworks Solutions, Inc. 4311 Jamboree Rd. Newport Beach, CA. 92660-3007 www.skyworksinc.com