R9220 HAMAMATSU
Document overview
- PDF pages: 4
Technical content
Page 1

High QE Multialkali Photocathode
New Electro–Optical Design
28 mm (1-1/8 Inch) Diameter, 9-stage, Side-on Type
FEATURES
GHigh Cathode Sensitivity Luminous ................................................. 450 µA/lm (Typ.) Radiant at 450 nm (peak) ........................ 85 mA/W (Typ.) Quantum Efficiency at 260 nm (peak) .... 26.3 % (Typ.) GHigh Anode Sensitivity at 1000 V Luminous ................................................. 4500 A/lm (Typ.) Radiant at 450 nm (peak) ........................ 8.5 × 105 A/W (Typ.) GWide Spectral response ............................. 185 nm to 900 nm GHigh Signal to Noise Ratio GNewly Designed Electro Optical Structure
APPLICATIONS
GBiomedical Fluorescence Detection GLaser Scanning Detection GSpectroscopy GSemiconductor Inspection GEnvironmental Monitoring
Figure 1: Electro optical Structure
LIGHT

TPMSC0024EB

Figure 2: Typical Spectral Response

WAVELENGTH (nm)
Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2006 Hamamatsu Photonics K.K.
Page 2
PHOTOMULTIPLIER TUBE R9220
SPECIFICATIONS
GENERAL
| Parameter | Description/Value | Unit | |
|---|---|---|---|
| Spectral Response | 185 to 900 | nm | |
| Wavelength of Maximum Response | 450 | nm | |
| Photocathode | MateriaI | Multialkali | — |
| Minimum Effective Area | 8 × 24 | mm | |
| Window Material | UV glass | — | |
| Dynode | Structure | Circular-cage | — |
| Number of Stages | 9 | — | |
| Direct Interelectrode Capacitances | Anode to Last Dynode | 4 | pF |
| Anode to All Other Electrodes | 6 | pF | |
| Base | 11-pin base JEDEC No. B11-88 | — | |
| Weight | Approx. 45 | g | |
| Operating Ambient Temperature | -30 to +50 | °C | |
| Storage Temperature | -30 to +50 | °C | |
| SuitabIe Socket | E678–11A (Sold Separately) | — | |
| SuitabIe Socket Assembly | E717–63 (Sold Separately) | — | |
MAXIMUM RATINGS (Absolute Maximum Values)
| Parameter | Value | Unit | |
|---|---|---|---|
| Supply Voltage | Between Anode and Cathode | 1250 | V |
| Between Anode and Last Dynode | 250 | V | |
| Average Anode Current A | 0.1 | mA | |
CHARACTERISTlCS (at 25 °C)
| Parameter | Min. | Typ. | Max. | Unit | |||
|---|---|---|---|---|---|---|---|
| Cathode Sensitivity | Quantum Efficiency | at 260 nm | — | 26.3 | — | % | |
| at 450 nm | — | 23.4 | — | % | |||
| at 633 nm | — | 13.3 | — | % | |||
| Luminous B | 375 | 450 | — | µA/lm | |||
| Radiant | at 450 nm | — | 85 | — | mA/W | ||
| at 633 nm | — | 68 | — | mA/W | |||
| Red/White Ratio C | — | 0.4 | — | — | |||
| Blue Sensitivity Index D | — | 12.5 | — | — | |||
| Anode Sensitivity | Luminous E | 1000 | 4500 | — | A/lm | ||
| Radiant at 450 nm (peak) | 8.5 × 105 | A/W | |||||
| Gain E | — | 1.0 × 107 | — | — | |||
| Anode Dark Current F (After 30 min Storage in Darkness) | — | 10 | 50 | nA | |||
| Time Response | Anode Pulse Rise Time G | — | 2.2 | — | ns | ||
| Electron Transit Time H | — | 22 | — | ns | |||
| Transit Time Spread (TTS) I | — | 1.2 | — | ns | |||
| Anode Current Stability J | Light Hysteresis | — | 0.1 | — | % | ||
| Voltage Hysteresis | — | 1.0 | — | % | |||
NOTES
A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 volts between the cathode and all other electrodes connected together as anode. C: Red/White ratio is the quotient of the cathode current measured using a red filter (Toshiba R-68) interposed between the light source and the tube by the cathode current measured with the filter removed under the same conditions as Note B. D: The value is cathode output current when a blue filter (Corning CS 5-58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same condition as Note B.
E: Measured with the same light source as Note B and with the voltage distribution ratio shown in Table 1 below.
Table 1: Voltage Distribution Ratio
| Electrodes | K | Dy1 | Dy2 | Dy3 | Dy4 | Dy5 | Dy6 | Dy7 | Dy8 | Dy9 | P | |||||||||||
| Ratio | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | ||||||||||||
SuppIy Voltage: 1000 V, K: Cathode, Dy: Dynode, P: Anode
F: Measured with the same supply voltage and voltage distribution ratio as Note E after removal of light. G: The rise time is the time for the output pulse to rise from 10 % to 90 % of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse. H: The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitube. In measurement, the whole photocathode is illuminated. I : Also called transit time jitter. This is the fluctuation in electron transit time between individual pulses in the single photoelectron mode, and may be defined as the
FWHM of the frequency distribution of electron transit times. J: Hysteresis is temporary instability in anode current after light and voltage are applied.
lmax. – lmin.
× 100(%)
Hysteresis =
li
l max.
il l min. TIME
5 6 7 (minutes)
0
TPMSB0002EA
(1)Light Hysteresis The tube is operated at 750 volts with an anode current of 1 microampere for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated by the previous light level for a minute to measure the variation. (2)Voltage Hysteresis The tube is operated at 300 volts with an anode current of 0.1 micro-ampere for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 volts. After a minute, the supply voltage is then reduced to the previous value and the tube is re-illuminated for a minute to measure the variation.
Page 3
Figure 3: Typical Temperature Characteristics of Dark Current
(at 1000 V, after 30 minute storage in darkness)
TPMSB0202EB

TEMPERATURE (°C)
Figure 5: Typical Time Response

SUPPLY VOLTAGE (V)
Figure 4: Anode Luminous Sensitivity and Gain Characteristics
TPMSB0203EB

SUPPLY VOLTAGE (V)
Figure 6: Typical Temperature Coefficient of Anode Sensitivity

WAVELENGTH (nm)
Page 4
PHOTOMULTIPLIER TUBE R9220
Figure 7: Dimensional Outline and Basing Diagram (Unit: mm)

DY6

BOTTOM VIEW
(BASING DIAGRAM)
Figure 8: Socket (Unit: mm) Sold Separately
E678-11A
E717-63

Cross Section
TPMSA0001EA
TPMSA0009EB
Sold Separately
Figure 9: D-Type Socket Assembly (Unit: mm)



TACCA0064EA
\* Hamamatsu also provides C4900 series compact high voltage
power supplies and C6270 series DP type socket assemblies
which incorporate a DC to DC converter type high voltage
power supply.
\* PATENT PENDING: JAPAN 4, USA 4, EUROPE 4
SOCKET

SIGNAL OUTPUT RG-174/U(BLACK) POWER SUPPLY GND AWG22 (BLACK)

AWG22 (VIOLET)
TACCA0002EH

WEB SITE www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Electron Tube Division 314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: infos@hamamatsu.fr
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: info@hamamatsu.co.uk North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: info@hamamatsu.se
TPMS1071E02
Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: info@hamamatsu.it
JUL. 2006 IP