R9110 HAMAMATSU

Document overview

  • PDF pages: 4

Technical content

Page 1

PDF page 1 diagram

High Sensitivity and Lower Dark Current

Wide Spectral Range with Low ENI, 8 mm × 6 mm Photocathode Size

PDF page 1 diagram

FEATURES

G Low Dark Current ...................................... 5 nA (after 30 minutes) G Wide Spectral Response .......................... 185 nm to 900 nm G High Cathode Sensitivity Luminous ................................................ 525 µA/lm Radiant at 450 nm .................................. 90 mA/W QE at 450 nm .......................................... 24.8 % G High Anode Sensitivity (at 1000 V) Luminous ................................................ 10 000 A/lm G High Signal to Noise Ratio

The R9110 is a 28 mm (1-1/8 inch) diameter, 9-stage, side-on type photomultiplier tube having an extended red multialkali photocathode same as the R3896. The R9110 features very low dark current, ex- tremely high quantum efficiency, high gain, good S/N ratio and wide spectral response from UV to near infrared. The R9110 is directly pin compatible with the R3896.

GENERAL

Parameter Description/Value Unit
Spectral Response 185 to 900 nm
Peak Wavelength 450 nm
Photocathode Material Minimum Effective Area Multialkali 8 6 — mm
Window Material × UV glass —
Dynode Secondary Emitting Surface Multialkali —
Structure Circular-cage —
Number of Stages 9 —
Direct Interelectrode Capacitances Anode to Last Dynode Approx. 4 pF
Anode to All Other Electrodes Approx. 6 pF
Base 11-pin base JEDEC No. B11-88 —
Weight Approx. 46 g
Operating Ambient Temperature -30 to +50 °C
Storage Temperature -30 to +50 °C
Suitable Socket E678-11A (Sold Separately) —
Suitable Socket Assembly E717-63 (Sold Separately) —
E717-74 (Sold Separately)

Figure 1: Typical Spectral Response and Equivalent Noise Input

PDF page 1 diagram

WAVELENGTH (nm)

Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2006 Hamamatsu Photonics K.K.

Page 2

PHOTOMULTIPLIER TUBE R9110

MAXIMUM RATINGS (Absolute Maximum Values at 25 °C)

Parameter Value Unit
Supply Voltage Between Anode and Cathode 1250 V
Between Anode and Last Dynode 250 V
Average Anode Current A 0.1 mA

CHARACTERISTlCS (at 25 °C)

Parameter Min. Typ. Max. Unit
Cathode Sensitivity Quantum Efficiency at 254 nm — 29.3 — %
at 450 nm — 24.8 — %
at 633 nm — 14.3 — %
at 852 nm — 0.73 — %
Luminous B 400 525 — µA/lm
Radiant at 254 nm — 60 — mA/W
at 450 nm — 90 — mA/W
at 633 nm — 73 — mA/W
at 852 nm — 5.0 — mA/W
Red/White Ratio C — 0.4 — —
Blue Sensitivity Index D — 15 — —
Anode Sensitivity Luminous E 4000 10 000 — A/lm
Gain E — 1.9 × 107 — —
Anode Dark Current F (After 30 min Storage in Darkness) — 5 15 nA
Time Response Anode Pulse Rise Time G — 2.2 — ns
Electron Transit Time H — 22 — ns
Transit Time Spread (TTS) I — 1.2 — ns
Anode Current Stability J Light Hysteresis — 0.1 — %
Voltage Hysteresis — 1.0 — %

NOTES

A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 volts between the cathode and all other electrodes connected together as anode. C:Red/White ratio is the quotient of the cathode current measured using a red filter(Toshiba R-68) interposed between the light source and the tube by the cathode current measured with the filter removed under the same conditions as Note B. D:The value is cathode output current when a blue filter(Corning CS 5-58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same condition as Note B.

E: Measured with the same light source as Note B and with the voltage distribution ratio shown in Table 1 below.

Table 1:Voltage Distribution Ratio

Electrodes K Dy1 Dy2 Dy3 Dy4 Dy5 Dy6 Dy7 Dy8 Dy9 P
Distribution Ratio 1 1 1 1 1 1 1 1 1 1

SuppIy Voltage: 1000 V, K: Cathode, Dy: Dynode, P: Anode

F: Measured with the same supply voltage and voltage distribution ratio as Note E after removal of light. G:The rise time is the time for the output pulse to rise from 10% to 90% of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse. H:The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitube. In measurement, the whole photocathode is illuminated. I: Also called transit time jitter. This is the fluctuation in electron transit time between individual pulses in the single photoelectron mode, and may be defined

as the FWHM of the frequency distribution of electron transit times J: Hysteresis is temporary instability in anode current after light and voltage are applied.

lmax. lmin.

Hysteresis =

100 (%) li

l max.

il l min.

TIME

5 6 7 (minutes)

0

TPMSB0002EA

(1)Light Hysteresis The tube is operated at 750 volts with an anode current of 1 microampere for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated by the previous light level for a minute to measure the variation. (2)Voltage Hysteresis The tube is operated at 300 volts with an anode current of 0.1 micro-ampere for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 volts. After a minute, the supply voltage is then reduced to the previous value and the tube is re-illuminated for a minute to measure the variation.

Page 3

VOLTAGE DISTRIBUTION RATIO

Electrodes

K Dy1 Dy2 Dy3 Dy4 Dy5 Dy6

Dy7 Dy8 Dy9 P

Distribution Ratio

1 1 1 1 1 1 1 1 1 1

K: Cathode, Dy: Dynode, P: Anode

NOTE: For a high speed pulse measurement, below voltage divider ratio is recommended.

PDF page 3 diagram

Figure 2: Anode Luminous Sensitivity and Gain Characteristics

PDF page 3 diagram

SUPPLY VOLTAGE (V)

Figure 3: Typical Time Response

PDF page 3 diagram

SUPPLY VOLTAGE (V)

Page 4

PHOTOMULTIPLIER TUBE R9110

Figure 4: Dimensional Outline and Basing Diagram (Unit: mm)

PDF page 4 diagram

Figure 6: D Type Socket Assembly (Unit: mm) Sold Separately

E717-63

PDF page 4 diagram

SOCKET

PDF page 4 diagram

SIGNAL OUTPUT RG-174/U(BLACK) POWER SUPPLY GND AWG22 (BLACK)

29.0 ± 0.3

0.7 31.0 ± 0.5 HOUSING (INSULATOR) POTTING COMPOUND

AWG22 (VIOLET)

TACCA0002EH

\* Hamamatsu also provides C4900 series compact high voltage power

Figure 5: Socket (Unit: mm) Sold Separately

E678-11A

PDF page 4 diagram
PDF page 4 diagram

TACCA0064EA

E717-74 HOUSING

PDF page 4 diagram

SOCKET PMT

PDF page 4 diagram
PDF page 4 diagram

: 330 kΩ : 10 nF

To supply +HV,connect the pin "G" to+HV, and the pin "K" to the GND.

TACCA0277EA

PDF page 4 diagram

supplies and C6270 series DP type socket assemblies which incor- porate a DC to DC converter type high voltage power supply.

WEB SITE www.hamamatsu.com

HAMAMATSU PHOTONICS K.K., Electron Tube Division 314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205

U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: infos@hamamatsu.fr United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: info@hamamatsu.co.uk

North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: info@hamamatsu.se Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: info@hamamatsu.it

TPMS1072E02

JUL. 2006. IP