R6925 HAMAMATSU

Document overview

  • PDF pages: 4

Technical content

Page 1

PHOTOMULTIPLIER TUBE

R6925

High Sensitivity Bialkali Photocathode

28mm (1-1/8 Inch) Diameter, 9-Stage, Side-On Type

FEATURES

Spectral Response ............................ 185 to 730 nm Cathode Sensitivity

Luminous ........................................70 µA/lm Typ.

Radiant at 410 nm .......................... 68mA/W Typ.

Anode Sensitivity (at 1000V)

Luminous ......................................... 500A/lm Typ. Radiant at 410 nm ................... 4.8 × 105A/W Typ.

APPLICATIONS

Fluorescence Spectrophotometers Emission Spectrophotometers Atomic Absorption Spectrophotometers

GENERAL

PDF page 1 diagram
PDF page 1 diagram

Figure 1: Typical Spectral Response

TPMSB0123EA

PDF page 1 diagram

WAVELENGTH (nm)

Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©1997 Hamamatsu Photonics K.K

Page 2

PHOTOMULTIPLIER TUBE R6925

MAXIMUM RATINGS (Absolute Maximum Values)

PDF page 2 diagram

CHARACTERISTICS (at 25°C)

Parameter Min. Typ. Max. Unit
Cathode sensitivity Quantum Efficiency at Peak Wavelength LuminousB Radiant at 410nm Red/White RatioC BlueD — 23 — (at 250nm) 40 70 — — 68 — — 0.02 — — 7 — % µ A/lm mA/W — µ A/lm-blue
Anode Sensitivity LuminousE Radiant at 410nm 200 500 — — 4.8 × 105 — A/lm A/W
Gain — 7.1 × 106 — —
Anode Dark CurrentF (After 30 minutes storage in the darkness) — 5 50 nA
ENI (Equivalent Noise Input)G — 2.2 × 10-16 — W
Time ResponseE Anode Pulse Rise TimeH Electron Transit TimeI Transit Time Spread (TTS)J — 2.2 — — 22 — — 1.2 — ns ns ns
Anode Current StabilityK Light Hysteresis Voltage Hysteresis — 0.1 — — 1.0 — % %

NOTES

A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 volts between the cathode and all other electrodes connected together as anode. C: Red/White ratio is the quotient of the cathode current measured us- ing a red filter(Toshiba R-68) interposed between the light source and the tube by the cathode current measured with the filter removed under the same conditions as Note B. D: The value is cathode output current when a blue filter(Corning CS-5- 58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same condition as Note B.

E: Measured with the same light source as Note B and with the voltage distribution ratio shown in Table 1 below.

Table 1: Voltage Distribution Ratio

Electrode K Dy1 Dy2 Dy3 Dy4 Dy5 Dy6 Dy7 Dy8 Dy9 P
Distribution Ratio 1 1 1 1 1 1 1 1 1 1

Supply Voltage=1000Vdc K:Cathode Dy:Dynode P:Anode

F: Measured with the same supply voltage and voltage distribution ratio as Note E after removal of light. G: ENI is an indication of the photon-limited signal-to-noise ratio. It re- fers to the amount of light in watts to produce a signal-to-noise ratio of unity in the output of a photomultiplier tube.

2q·ldb·G·∆f ENI = S

where q = Electronic charge (1.60 × 10-19 coulomb). ldb = Anode dark current(after 30 minutes storage) in am- peres. G = Gain. ∆f = Bandwidth of the system in hertz. 1 hertz is used. S = Anode radiant sensitivity in amperes per watt at the wavelength of peak response.

H: The rise time is the time for the output pulse to rise from 10% to 90% of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse.

Page 3

I: The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitude. In measurement, the whole photocathode is illuminated.

J: Also called transit time jitter. This is the fluctuation in electron transit time between individual pulses in the signal photoelectron mode, and may be defined as the FWHM of the frequency distribution of electron transit times.

K: Hysteresis is temporary instability in anode current after light and voltage are applied.

l max.

il

l min.

TIME

5 6 7 (minutes)

0

TPMSB0002EA

Figure 2: Typical Gain and Anode Luminous Sensitivity

TPMSB0124EB

PDF page 3 diagram

SUPPLY VOLTAGE (V)

Figure 4:

Typical ENI with Wavelength

TPMSB0125EA

PDF page 3 diagram

WAVELENGTH (nm)

lmax — lmin.

Hysteresis =

× 100(%) li

(1) Light Hysteresis The tube is operated at 750 volts with an anode current of 1 micro-am- pere for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated by the previous light level for a minute to measure the variation.

(2) Voltage Hysteresis The tube is operated at 300 volts with an anode current of 0.1 microampere for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 volts. After a minute, the supply voltage is then reduced to the previous value and the tube is re- illuminated for a minute to measure the variation.

Figure 3: Typical Time Response

TPMSB0004EB

PDF page 3 diagram

SUPPLY VOLTAGE (V)

Figure 5: Typical EADCI (Equivalent Anode Dark Current Input) vs. Supply Voltage

TPMSB0126EA

PDF page 3 diagram

SUPPLY VOLTAGE (V)

Page 4

PHOTOMULTIPLIER TUBE R6925

Unit: mm

Figure 6: Dimensional Outline and Basing Diagram

Figure 7: Socket E678-11A (Option)

PDF page 4 diagram

49

PDF page 4 diagram

DY6 DY5 6 DY7 5 7 4

DY8 8 3 9 DY9 2 10 P 1 11 DY1 K DIRECTION OF LIGHT

Bottom View (Basing Diagram)

TACCA0064EA

TPMSA0005EB

Figure 8: D Type Socket Assembly E717-21 (Option)

PDF page 4 diagram

SOCKET

PDF page 4 diagram
PDF page 4 diagram

\* Hamamatsu also provides compact high voltage power supplies and C956 se- ries DP type socket assemblies which incorporate a DC to DC converter type high voltage power supply.

SIGNAL OUTPUT RG-174/U (BLACK) POWER SUPPLY GND AWG22 (BLACK)

AWG22 (VIOLET)

TACCA0002EC

PDF page 4 diagram

HAMAMATSU PHOTONICS K.K., Electoron Tube Center 314-5, Shimokanzo, Toyooka-village, Iwata-gun, Shizuoka-ken, 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limted: Lough Point, 2 Gladbeck Way, Windmill Hill, Enfield, Middlesex EN2 7JA, United Kingdom, Telephone: (44)181-367-3560, Fax: (44)181-367-6384

North Europe: Hamamatsu Photonics Norden AB: Färögatan 7, S-164-40 Kista Sweden, Telephone: (46)8-703-29-50, Fax: (46)8-750-58-95

Cat. No. TPMS1034E01

Italy: Hamamatsu Photonics Italia: S.R.L.: Via Della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)2-935 81 733, Fax: (39)2-935 81 741

JUL. 1997 T Printed in Japan (1,500)