R3788 HAMAMATSU
Document overview
- PDF pages: 4
Technical content
Page 1
PHOTOMULTlPLlER TUBES
R3788, R4332

High Sensitivity, Bialkali Photocathode
28mm (1-1/8 Inch) Diameter, 9-Stage, Side-On Type

Figure 1: Typical Spectral Response
TPMSB0081EA

WAVELENGTH (nm)
Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. © 1994 Hamamatsu Photonics K.K.
Page 2
PHOTOMULTlPLlER TUBES R3788, R4332
MAXIMUM RATINGS (Absolute Maximum Values)

CHARACTERISTlCS (at 25 )
R3788
Parameter
Typ. Min.
Cathode Sensitivity
30
Quantum Efficiency at Peak Wavelength
(at 250nm) 100 120
Luminous B Radiant at 194nm
31
210nm
50
420nm
90 0.01
Red/White Ratio C Blue D
10
Anode Sensitivity Luminous E
500 1200
Radiant at 194nm
3.1 105
210nm
5.0 105
420nm
9.0 105
Gain E
1.0 107
5
Anode Dark Current F (After 30minutes Storage in the darkness)
ENI(Equivalent Noise Input) G
1.4 10-16
Time Response E
2.2
Anode Pulse Rise Time H
22
Electron Transit Time I Transit Time Spread (TTS) J
1.2
Anode Current Stability K Light Hysteresis
0.1
Voltage Hysteresis
1.0
NOTES
A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 volts between the cathode and all other electrodes connected together as anode. Red/White ratio is the quotient of the cathode current measured using a C: red filter(Toshiba R-68) interposed between the light source and the tube by the cathode current measured with the filter removed under the same conditions as Note B. D:The value is cathode output current when a blue filter(Corning CS-5-58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same condition as Note B.
E: Measured with the same light source as Note B and with the voltage distribution ratio shown in Table 1 below.
Table 1:Voltage Distribution Ratio
Electrodes
K Dy1 Dy2 Dy3 Dy4 Dy5 Dy6 Dy7 Dy8 Dy9 P
Distribution Ratio SuppIy Voltage : 1000Vdc K : Cathode, Dy : Dynode, P : Anode
R4332
Unit
Typ.
Max. Min.
Max.
40
%
(at 210nm) 100 120
A/lm
60
mA/W
68
mA/W
90
mA/W
0.01 10
A/lm-b
500 1200
A/lm
6.0 105
A/W
6.8 105
A/W
9.0 105
A/W
1.0 107
50
5 50
nA
1.4 10-16
W
2.2
ns
22
ns
1.2
ns
0.1
%
1.0
%
F: Measured with the same supply voltage and voltage distribution ratio as Note E after removal of light. G:ENI is an indication of the photon-limited signal-to-noise ratio. It refers to the amount of light in watts to produce a signal-to-noise ratio of unity in the output of a photomultiplier tube. ENI = 2q.ldb.G. f S
where q = Electronic charge (1.60 10-19 coulomb). ldb = Anode dark current(after 30 minutes storage) in amperes. G = Gain. f = Bandwidth of the system in hertz. 1 hertz is used. S = Anode radiant sensitivity in amperes per watt at the wavelength of peak response. H:The rise time is the time for the output pulse to rise from 10% to 90% of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse.
Page 3
I: The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitude. In measurement, the whole photocathode is illuminated.
J: Also called transit time jitter. This is the fluctuation in electron transit time between individual pulses in the signal photoelectron mode, and may be defined as the FWHM of the frequency distribution of electron transit times.
K: Hysteresis is temporary instability in anode current after light and voltage are applied.
l max.
il l min. TIME
5 6 7 (minutes)
0
TPMSB0002EA
Figure 2: Anode Luminous Sensitivity and
Gain Characteristics
TPMSB0032EB

SUPPLY VOLTAGE (V)
Figure 4: Typical ENI with Wavelength
TPMSB0082EA

WAVELENGTH (nm)
lmax lmin.
Hysteresis =
100(%) li
(1)Current Hysteresis The tube is operated at 750 volts with an anode current of 1 micro-ampere for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated by the previous light level for a minute to measure the variation.
(2)Voltage Hysteresis The tube is operated at 300 volts with an anode current of 0.1 micro-ampere for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 volts. After a minute, the supply voltage is then reduced to the previous value and the tube is re-illuminated for a minute to measure the variation.
Figure 3: Typical Time Response
TPMSB0004EB

SUPPLY VOLTAGE (V)
Figure 5: Typical EADCI (Equivalent Anode Dark Current Input)
vs. Supply Voltage
TPMSB0034EA

SUPPLY VOLTAGE (V)
Page 4
PHOTOMULTlPLlER TUBES R3788, R4332
Unit : mm
Figure 6: Dimensional Outline and Basing Diagram
Figure 7: Socket E678-11A (Option)


DY6 DY5 6 DY7 5 7 4
DY8 8 3 9 DY9 2 10 P 1 11 DY1 K DIRECTION OF LIGHT
BOTTOM VIEW
(BASING DIAGRAM)
TACCA0008EB
TPMSA0005EB
Figure 8: D Type Socket Assembly E717-21 (Option)

SOCKET

SIGNAL OUTPUT RG-174/U
POWER SUPPLY GND

R to R10 : 330k C1 to C3: 0.01 F
TACCA0002ED
Hamamatsu also provides C4900 series compact high voltage power supplies and C6270 se- ries DP type socket assemblies which incorporate a DC to DC converter type high voltage power supply.

HAMAMATSU PHOTONICS K.K., Electoron Tube Center 314-5, Shimokanzo, Toyooka-village, Iwata-gun, Shizuoka-ken, 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limted: Lough Point, 2 Gladbeck Way, Windmill Hill, Enfield, Middlesex EN2 7JA, United Kingdom, Telephone: (44)181-367-3560, Fax: (44)181-367-6384
TPMS1021E01
North Europe: Hamamatsu Photonics Norden AB: Färögatan 7, S-164-40 Kista Sweden, Telephone: (46)8-703-29-50, Fax: (46)8-750-58-95
FEB. 1994
Italy: Hamamatsu Photonics Italia: S.R.L.: Via Della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)2-935 81 733, Fax: (39)2-935 81 741