R2949 HAMAMATSU
Document overview
- PDF pages: 4
Technical content
Page 1
PHOTOMULTIPLIER TUBE
R2949
(Low Dark Counts Type of R928)
Modified R928, 8 × 6mm Photocathode Area Size
Low Dark Counts, Extended Red Multialkali, High Sensitivity
For Photon Counting Applications

FEATURES
Low Dark Counts ................................................. 300cps (at 25°C) Low Dark Current ............................................. 2nA (after 30min.) Wide Spectral Response ........................................ 185 to 900 nm High Cathode Sensitivity Luminous ...................................................................... 200µA/lm Radiant at 400nm ........................................................... 68mA/W High Anode Sensitivity (at 1000V) Luminous ...................................................................... 2000A/lm Radiant at 400nm .................................................... 6.8 × 105A/W Low Drift and Hysteresis
The R2949 is a 28mm (1-1/8 inch) diameter, 9-stage, side-on type photomultiplier tube having the same extended red multialkali photocathode as the R928. The R2949 features very low dark counts, extremely high quantum efficiency, high gain, good S/N ratio and wide spectral response from UV to near infrared. The R2949 is well suited for use in various low-level photometries such as general single photon counting applications and fluorescence life time measurement. The R2949 is directly interchangeable with the R928.
GENERAL
Figure 1: Typical Spectral Response
| Parameter | Description/Value | Unit | |
|---|---|---|---|
| Spectral Response | 185 to 900 | nm | |
| Wavelength of Maximum Response | 400 | nm | |
| Photocathode | Material | Multialkali | — |
| Minimum Useful Size | 8 × 6 | mm | |
| Window Material | UV glass | — | |
| Dynode | Secondary Emitting Surface | Multialkali | — |
| Structure | Circular-cage | — | |
| Number of Stages | 9 | — | |
| Direct Interelectrode Capacitances | Anode to Last Dynode | Approx. 4 | pF |
| Anode to All Other Electrodes | Approx. 6 | pF | |
| Base | 11-pin base JEDEC No. B11-88 | — | |
| Weight | Approx. 45 | g | |
| Suitable Socket (Option) | E678-11A | — | |
| Suitable Socket Assembly (Option) | E717-21 | — | |
TPMSB0155EA 100
CATHODE RADIANT SENSITIVITY
10
QUANTUM EFFICIENCY
1
0.1
0.01 200 400 600 800 1000
WAVELENGTH (nm)
Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. © 1998 Hamamatsu Photonics K.K.
Page 2
PHOTOMULTIPLIER TUBE R2949
MAXIMUM RATINGS (Absolute Maximum Values at 25°C)
| Parameter | Value | Unit | |
|---|---|---|---|
| Supply Voltage | Between Anode and Cathode | 1250 | Vdc |
| Between Anode and Last Dynode | 250 | Vdc | |
| Average Anode Current A | 0.1 | mA | |
| Ambient Temperature | -80 to +50 | °C | |
CHARACTERISTICS (at 25°C)
| Parameter | Min. | Typ. | Max. | Unit | ||
|---|---|---|---|---|---|---|
| Cathode Sensitivity | Quantum Efficiency | at 255nm | — | 25.3 | — | % |
| Luminous B | 140 | 200 | — | µA/lm | ||
| Radiant | at 194nm | — | 18 | — | mA/W | |
| at 254nm | — | 52 | — | mA/W | ||
| at 400nm | — | 68 | — | mA/W | ||
| at 633nm | — | 41 | — | mA/W | ||
| at 852nm | — | 3.5 | — | mA/W | ||
| Red/White Ratio C with R-68 Filter | 0.1 | 0.3 | — | — | ||
| Blue D | — | 7.5 | — | µA/lm-b | ||
| Anode Sensitivity | Luminous E | 1000 | 2000 | — | A/lm | |
| Radiant | at 194nm | — | 1.8 × 105 | — | A/W | |
| at 254nm | — | 5.2 × 105 | — | A/W | ||
| at 400nm | — | 6.8 × 105 | — | A/W | ||
| at 633nm | — | 4.1 × 105 | — | A/W | ||
| at 852nm | — | 3.5 × 104 | — | A/W | ||
| Gain E | — | 1.0 × 107 | — | — | ||
| Anode Dark Counts F | at +25°C | — | 300 | 500 | cps | |
| at -20°C | — | 3 | — | cps | ||
| Anode Dark Current F | — | 2 | 25 | nA | ||
| ENI (Equivalent Noise Input) G | — | 1.2 × 10-16 | — | W | ||
| Time Response E | Anode Pulse Rise Time H | — | 2.2 | — | ns | |
| Electron Transit Time J | — | 22 | — | ns | ||
| Anode Current Stability K | Current Hysteresis | — | 0.1 | — | % | |
| Voltage Hysteresis | — | 1.0 | — | % | ||
Table 1: Voltage Distribution Ratio
| Electrodes | K | Dy1 | Dy2 | Dy3 | Dy4 | Dy5 | Dy6 | Dy7 | Dy8 | Dy9 | P | |||||||||||
| Distribution Ratio | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | ||||||||||||
Supply Voltage= 1000Vdc
K: Cathode, Dy: Dynode, P: Anode
NOTES
A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 volts between the cathode and all other electrodes connected together as anode. C: Red/white ratio is the quotient of the cathode current measured using a red filter interposed between the light source and the tube by the cathode current measured with the filter removed under the same conditions as Note B. D: The value is cathode output current when a blue filter (Corning CS 5-58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same conditions as Note B.
E: Measured with the same light source as Note B and with the anode-to-cathode supply voltage and voltage distribution ratio shown in Table 1. F: Measured with the same supply voltage and the voltage distribution ratio as Note E after 30 minute storage in the darkness. G: ENI is an indication of the photon limited signal-to-noise ratio. It refers to the amount of light in watts to produce a signal-to-noise ratio of unity in the output of a photomultiplier tube.
2q•ldb•G•∆f ENI = S
where q = Electronic charge (1.60 × 10-19 coulomb) ldb = Anode dark current (after 30 minute storage) in darkness) in amperes G = Gain ∆f = Bandwidth of the system in hertz. 1 hertz is used. S = Anode radiant sensitivity in amperes per watt at the wavelength of peak response.
H: The rise time is the time for the output pulse to rise from 10% to 90% of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse. J: The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitude. In measurement, the whole photocathode is illuminated. K. Hysteresis is temporary instability in anode current after light and voltage are applied.
Imax.
Ii Imin. TIME
0 5 6 7 (MINUTES)
Imax. - Imin. Hysteresis = × 100 (%)
Ij
(1) Current Hysteresis The tube is operated at 750 volts with an anode current of 1 microampere for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated at the previous light level for a minute to measure the variation.
(2)Voltage Hysteresis The tube is operated at 300 volts with an anode current of 0.1 microampere for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 volts. After a minute, the supply voltage is reduced to the previous value and the tube is re-illuminated for a minute to measure the variation.
Page 3
Figure 2: Anode Sensitivity and Gain Characteristics
TPMSB0156EA

SUPPLY VOLTAGE (V)
Figure 4: Typical Temperature Coefficient of Anode
Sensitivity
TPMSB0158EA

TEMPERATURE (°C)
Figure 3: Typical Time Response
TPMSB0157EA

SUPPLY VOLTAGE (V)
Figure 5: Typical Temperature Characteristic of Dark
Counts
TPMSB0159EA

10000
TEMPERATURE (°C)
Page 4
PHOTOMULTIPLIER TUBE R2949
Figure 6: Single Photon Pulse Height Distribution
Figure 7: Dimensional Outline and Basing Diagram
(Unit: mm)


7.5 × 103
5.0 × 103
2.5 × 103
PULSE HEIGHT (Channel)
\* The supply voltage is set at gain to be 1 × 106
Figure 8: Optional Accessories (Unit: mm)
D Type Socket Assembly E717-21
E678-11A (Socket)

SOCKET


SIGNAL GND SIGNAL OUTPUT RG-174/U
POWER SUPPLY GND AWG22 (BLACK)


TACCA0064EA
\* Hamamatsu also provides C4900 series modular type high voltage power supplies and C6270 series DP type socket assemblies which incorporate a DC to DC converter type high voltage power supply.
HAMAMATSU PHOTONICS K.K., Electoron Tube Center
AWG22 (VIOLET)
TACCA0002ED
Warning-Personal Safety Hazards
Electrical Shock — Operating voltage
applied to this device presents shock hazard.
314-5, Shimokanzo, Toyooka-village, Iwata-gun, Shizuoka-ken, 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limted: Lough Point, 2 Gladbeck Way, Windmill Hill, Enfield, Middlesex EN2 7JA, United Kingdom, Telephone: (44)181-367-3560, Fax: (44)181-367-6384
North Europe: Hamamatsu Photonics Norden AB: Färögatan 7, S-164-40 Kista Sweden, Telephone: (46)8-703-29-50, Fax: (46)8-750-58-95 Italy: Hamamatsu Photonics Italia: S.R.L.: Via Della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)2-935 81 733, Fax: (39)2-935 81 741
TPMS1045E01 JUN. 1998