R2693 HAMAMATSU

Document overview

  • PDF pages: 4

Technical content

Page 1

PHOTOMULTlPLlER TUBES

R2693, R2693P

PDF page 1 diagram

Transmission Mode Low Noise Bialkali Photocathode

28mm (1-1/8 inch) Diameter, Side-on Type

PDF page 1 diagram

Figure 1: Electron Trajectories

LIGHT

PDF page 1 diagram

TPMSC0003EB

Figure 2: Typical Spatial Uniformity

Y-Axis

X-Axis

PDF page 1 diagram
PDF page 1 diagram

Y SPOTSIZE : 1mm DIA SUPPLY VOLTAGE : 1000V X WAVELENGTH : 400nm

DISTANCE FROM CENTER OF

DISTANCE FROM CENTER OF

PHOTOCATHODE (mm)

TPMSB0066EA

PHOTOCATHODE (mm)

Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. © 1993 Hamamatsu Photonics K.K.

Page 2

PHOTOMULTlPLlER TUBES R2693, R2693P

MAXIMUM RATINGS (Absolute Maximum Values)

Parameter Value Unit
Supply Voltage Between Anode and Cathode 1250 Vdc
Between Anode and Last Dynode 250 Vdc
Average Anode Current A 0.1 mA
Ambient Temperature –80 to +50
CHARACTERISTlCS (at 25 ) R2693 for General Purpose R2693P for Photon Counting
Parameter Min. Typ. Max. Min. Typ. Max. Unit
Cathode Sensitivity Quantum Efficiency at 375nm 20.5 20.5 %
Luminous B 30 50 30 50 A/lm
Radiant at 375nm (Peak) 62 62 mA/W
Blue C 7.0 7.0 A/lm-b
Anode Sensitivity Luminous D 100 300 100 300 A/lm
Radiant at 375nm 3.7 105 3.7 105 A/W
Gain D 6 106 6 106
Anode Dark Current E (After 30min. storage in darkness) 0.5 5.0 0.1 2.0 nA
Anode Dark Counts E 15 50 cps
ENI(Equivalent Noise Input) F 8.6 10-17 3.9 10-17 W
D Time Response Anode Pulse Rise Time G 1.2 1.2 ns
Electron Transit Time H 18 18 ns
Transit Time Spread (FWHM) J 1.0 1.0 ns
Anode Current K Stability Current Hysteresis 0.5 0.5 %
Voltage Hysteresis 1.0 1.0 %

NOTES

A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 volts between the cathode and all other electrodes connected together as anode. C:The value is cathode output current when a blue filter(Corning CS-5-58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same condition as Note B. D:Measured with the same light source as Note B and with the voltage distribution ratio shown in Table 1 below.

Table 1:Voltage Distribution Ratio

Electrodes K Dy1 Dy2 Dy3• • • •Dy9 P
Ratio 1 1 1• • • • • • • • 1 1

R2693

Electrodes K Dy1 Dy2 Dy3• • • •Dy9 P
Ratio 2.5 1.5 1• • • • • • • • 1 1

R2693P

SuppIy Voltage : 1000Vdc, K : Cathode,Dy : Dynode, P : Anode

E: Measured with the same supply voltage and voltage distribution ratio as Note D after removal of light. F: ENI is an indication of the photon-limited signal-to-noise ratio. It refers to the amount of light in watts to produce a signal-to-noise ratio of unity in the output of a photomultiplier tube.

2q.ldb.G. f ENI = S

where q = Electronic charge (1.60 10-19 coulomb). ldb = Anode dark current(after 30 minutes storage) in amperes. G = Gain. f = Bandwidth of the system in hertz. 1 hertz is used. S = Anode radiant sensitivity in amperes per watt at the wavelength of peak response.

G:The rise time is the time for the output pulse to rise from 10% to 90% of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse. H:The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitube. In measurement, the whole photocathode is illuminated. J: Also called transit time jitter. This is the fluctuation in electron transit time between individual pulses in the single photoelectron mode, and may be defined as the FWHM of the frequency distribution of electron transit times. K: Hysteresis is temporary instability in anode current after light and

voltage are applied.

lmax. lmin.

Hysteresis =

100(%) li

l max.

il

l min.

TIME

5 6 7 (minutes)

0

TPMSB0002EA

(1)Current Hysteresis The tube is operated at 750 volts with an anode current of 1 microampere for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated by the previous light level for a minute to measure the variation. (2)Voltage Hysteresis The tube is operated at 300 volts with an anode current of 0.1 micro -ampere for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 volts. After a minute, the supply voltage is then reduced to the previous value and the tube is re-illuminated for a minute to measure the variation.

Page 3

Figure 3: Typical Spectral Response

TPMSB0060EA

PDF page 3 diagram

WAVELENGTH (nm)

Figure 5: Typical Gain and Anode Dark Current (R2693)

PDF page 3 diagram

SUPPLY VOLTAGE(V)

Figure 7: Typical Temperature Coefficient

of Anode Sensitivity

TPMSB0064EA

PDF page 3 diagram

WAVELENGTH (nm)

Figure 4: Typical Time Response

PDF page 3 diagram

SUPPLY VOLTAGE (V)

Figure 6: Typical Single Photoelectron Pulse Height

Distribution (R2693P)

TPMSB0063EA 1.0

+ SIGNAL DARK WAVELENGTH OF INCIDENT LIGHT : 400nm SUPPLY VOLTAGE : 1000vdc SIGNAL+DARK COUNTS : 5364cps DARK COUNTS : 15cps AMBIENT TEMPERATURE : + 25 DARK
0 200 400 600 800 10 CHANNEL NUMBER(ch)

0.8

0.6

0.4

0.2

0 0

1000

DISCRIMINATION LEVEL

Figure 8: Typical Temperature Characteristics

of Dark Current(R2693)

(at 1000V, after 30minutes storage)

PDF page 3 diagram

TEMPERATURE (°C)

Page 4

PHOTOMULTlPLlER TUBES R2693, R2693P

Figure 9: Dimensional Outline and Basing Diagram (Unit: mm)

PDF page 4 diagram

Figure 10: Optional Accessories (Unit: mm)

Socket E678-11A

DY6 DY7

DY5 6 5 7

DY4

DY8

4 8

DY3 3

9 DY9

2 10 P

DY2 1 11 K DY1 DIRECTION OF LIGHT

BOTTOM VIEW

(BASING DIAGRAM)

TPMSA0007EA

D Type Socket Assembly E717-21

PDF page 4 diagram

SOCKET

PDF page 4 diagram
PDF page 4 diagram

SIGNAL OUTPUT RG-174/U

POWER SUPPLY GND

PDF page 4 diagram

TACCA0008EB

Hamamatsu also provides C4900 series compact high voltage power supplies and C6270 series DP type socket assemblies which incorporate a DC to DC converter type high voltage power supply.

HAMAMATSU PHOTONICS K.K., Electoron Tube Center

R1 to R10 : 330k C1 to C3 : 0.01 F

TACCA0002ED

PDF page 4 diagram

314-5, Shimokanzo, Toyooka-village, Iwata-gun, Shizuoka-ken, 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limted: Lough Point, 2 Gladbeck Way, Windmill Hill, Enfield, Middlesex EN2 7JA, United Kingdom, Telephone: (44)181-367-3560, Fax: (44)181-367-6384

TPMS1014E01

North Europe: Hamamatsu Photonics Norden AB: Färögatan 7, S-164-40 Kista Sweden, Telephone: (46)8-703-29-50, Fax: (46)8-750-58-95 Italy: Hamamatsu Photonics Italia: S.R.L.: Via Della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)2-935 81 733, Fax: (39)2-935 81 741

MAR. 1993