PX1004 MURATA
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
www.RFM.com E-mail: info@rfm.com Page 1 of 5 ©2009 by RF Monolithics, Inc. PX1004 - 2/11/09
Electrical Characteristics
Characteristic Sym Notes Min Typ Max Units Nominal Center Frequency fC 1
82.200 MHz
Passband Insertion Loss at fc IL 34 . 0 d B 3 dB Passband BW3 1, 2 ±15 ±25 kHz Amplitude Ripple over fc ±15 kHz 1.0 dBP-P Group Delay Variation over fc ±10 kHz GDV 2.5 6.0 µsP-P Third-Order Intermod. for -20 dBm tones at fc ±60 & 120 kHz -95 dBm Rejection fc ±60 kHz 1, 2, 3 10 16 dBfc -880 kHz to fc -940 kHz 65 68 Ultimate 65 Operating Temperature Range TA 1- 2 0 +70 °C Impedance Matching to 50 Ω unbalanced External L-C Case Style SM13365-12 13.3 X 6.5 mm Nominal Footprint Lid Symbolization (YY=year, WW=week) See note 4 RFM PX1004 YYWW SM13365-12
- Designed for TDMA IS-54 / CDPD IF Applications Low Insertion Loss Excellent Selectivity Hermetic 13.3 X 6.5 mm Surface-Mount Case Unbalanced Input and Output Complies with Directive 2002/95/EC (RoHS) Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 °C Suitable for lead-free soldering - Max Soldering Profile 260°C for 30 s
82.2 MHz
- Unless noted otherwise, all specifications apply over the operating tem- perature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network ana- lyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. 9. ©Copyright 1999, RF Monolithics Inc. Caution: Electrostatic Sensitive Device. Observe precautions for handling. Notes: Electrical Connections Connection Terminals Port 1Hot 2 Port 1 Gnd Return 3 Port 2 Hot 8 Port 2 Gnd Return 9 Case Ground All Others Pb
www.RFM.com E-mail: info@rfm.com Page 2 of 5 ©2009 by RF Monolithics, Inc. PX1004 - 2/11/09
www.RFM.com E-mail: info@rfm.com Page 3 of 5 ©2009 by RF Monolithics, Inc. PX1004 - 2/11/09
www.RFM.com E-mail: info@rfm.com Page 4 of 5 ©2009 by RF Monolithics, Inc. PX1004 - 2/11/09 Tape and Reel Specifications Quantity Per Reel
100 Min
1000 Max
COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 7.0 mm Bo 13.8 mm Ko 2.0 mm Pitch 12.0 mm W 24.0 mm PIN #1 See Detail "A" 13.0 20.22.0 12.0 100 REF. "B" REF. 21.0 254 24.4
www.RFM.com E-mail: info@rfm.com Page 5 of 5 ©2009 by RF Monolithics, Inc. PX1004 - 2/11/09 SM13365-12 Case Case Dimensions Dimension mm Inches Min Nom Max Min Nom Max C 1.91 2.00 0.075 0.079 D 1.50 0.059 E 0.79 0.031 H 1.0 0.039 P 2.54 0.100 12-Terminal Ceramic Surface-Mount Case 13.3 x 6.5 mm Nominal Footprint Materials Solder Pad Termination Au plating 30 - 60 uInches (76.2-152 uM) over 80-200 uInches (203-508 uM) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phos- phorus) 100-200 uInches Thick Body Al 2O3 Ceramic Pb Free C H P (8 Places) E (10 Places) DB A 9 8 TOP VIEW BOTTOM VIEW 8 9 0.034 TYP. 0.100 TYP. (0.86) (2.54) 0.077 TYP. (1.96) 0.555 (14.10) 0.287 (7.29) 0.334 REF. (8.48)