PLX1V390MCL1_V01 NICHICON
Document overview
- PDF pages: 2
Technical content
Page 1
| CONDUCTIVE POLYMER ALUMINUM SOLID ELEC | TROLYTIC CAPACITORS |
|---|---|
| LXRadial Lead Type, Long Life Assurance series High reliability, High voltage (to 50V). Low ESR, High ripple current. Long life of 3000 hours at 125°C. LX Radial lead type: Lead free flow soldering condition correspondence. Adapted to the RoHS directive (2011/65/EU). Higher Temperature | |
LV
Specifications
| Item | Performance Characteristics |
| Category Temperature Range | –55 to +125°C |
| Rated Voltage Range | 16 to 50V |
| Rated Capacitance Range | 22 to 390µF |
| Capacitance Tolerance | ± 20% at 120Hz, 20°C |
| Tangent of loss angle (tan δ) | Less than or equal to the specified value at 120Hz, 20°C |
| ESR ( 1) | Less than or equal to the specified value at 100kHz, 20°C |
| Leakage Current ( 2) | Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C |
| Temperature Characteristics (Max.Impedance Ratio) | Z+125°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25 |
| Endurance | Capacitance change Within ± 20% of initial value ( 3) The specifications listed at below shall be met when the tan δ 150% or less of the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less of the initial specified value applied for 3000 hours at 125°C. Leakage current ( 2) Less than or equal to the initial specified value |
| Damp Heat (Steady State) | Capacitance change Within ± 20% of initial value ( 3) The specifications listed at below shall be met when the tan δ 150% or less of the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less of the initial specified value applied for 1000 hours at 60°C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value |
| Resistance to Soldering Heat Marking | After soldering the capacitor under the soldering conditions Capacitance change Within ± 10% of the initial capacitance value ( 3) prescribed here as preheat at 150 to 200°C for 60 to 180 seconds tan δ 130% or less than the initial specified value and peak temperature at 265°C for 10 seconds or less, the ESR ( 1) 130% or less than the initial specified value capacitor shall meet the specifications listed at below, provided Leakage current ( 2) Less than or equal to the initial specified value that its temperature profile is measured at both of terminal ends facing the soldering side. Navy blue print on the case top |
1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Resin coated Case

(mm)
| Size | φ8 × 9L | φ8 × 12L |
| φD | 8.0 | 8.0 |
| L | 8.5 | 11.5 |
| P | 3.5 | 3.5 |
| φd | 0.6 | 0.6 |
φ10 × 13L 10.0
Voltage
12.5 V 16 20 25 35
5.0
Code C D E V
0.6
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
Type numbering system (Example : 35V 39µF)
1 2 3 4 5 6 7 8 9 10 11 12

50 H
CAT.8100D
Page 2
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LXseries
Standard Ratings
| Rated Voltage (V)(code) | Surge Voltage (V) | Rated Capacitance (µF) | Case Size φD × L (mm) | tan δ | Leakage Current (µA) | ESR (mΩ) (at 100kHz 20°C) | Rated Ripple (mArms) | Part Number | |
|---|---|---|---|---|---|---|---|---|---|
| 16 (1C) | 18.4 | 150 | 8 × 9 | 0.12 | 480 | 26 | 2100 | 810 | PLX1C151MCL1 |
| 220 | 8 × 12 | 0.12 | 704 | 25 | 2400 | 930 | PLX1C221MDL1 | ||
| 390 | 10 × 13 | 0.12 | 1248 | 23 | 2900 | 1130 | PLX1C391MDL1 | ||
| 20 (1D) | 23.0 | 120 | 8 × 9 | 0.12 | 480 | 27 | 2000 | 800 | PLX1D121MCL1 |
| 150 | 8 × 12 | 0.12 | 600 | 26 | 2300 | 910 | PLX1D151MDL1 | ||
| 270 | 10 × 13 | 0.12 | 1080 | 24 | 2800 | 1110 | PLX1D271MDL1 | ||
| 25 (1E) | 28.7 | 82 | 8 × 9 | 0.12 | 410 | 28 | 2000 | 780 | PLX1E820MCL1 |
| 120 | 8 × 12 | 0.12 | 600 | 27 | 2300 | 890 | PLX1E121MDL1 | ||
| 180 | 10 × 13 | 0.12 | 900 | 25 | 2800 | 1080 | PLX1E181MDL1 | ||
| 35 (1V) | 40.2 | 39 | 8 × 9 | 0.12 | 273 | 33 | 1800 | 720 | PLX1V390MCL1 |
| 56 | 8 × 12 | 0.12 | 392 | 31 | 2100 | 830 | PLX1V560MDL1 | ||
| 100 | 10 × 13 | 0.12 | 700 | 28 | 2700 | 1040 | PLX1V101MDL1 | ||
| 50 (1H) | 57.5 | 22 | 8 × 9 | 0.12 | 220 | 35 | 1800 | 700 | PLX1H220MCL1 |
| 27 | 8 × 12 | 0.12 | 270 | 33 | 2000 | 810 | PLX1H270MDL1 | ||
| 47 | 10 × 13 | 0.12 | 470 | 29 | 2600 | 1020 | PLX1H470MDL1 | ||
Ambient temperature of a capacitor
Rated ripple current (mArms) at 105°C 100kHz
Please refer to page 20, 21, 22 about the formed or taped product spec. Please refer to page 3 for the minimum order quantity.