DATASHEET SEARCH SITE
Document overview
- PDF pages: 2
Technical content
Page 1
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LV series
Radial Lead Type, Long Life Assurance

High voltage (to 100V), Low ESR, High ripple current.
Long life of 3000 hours at 105°C.
Radial lead type:
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2002/95/EC).
LV
LF
LX High Temperature
High Voltage Long Life
Specifications
| Item | Performance Characteristics |
| Category Temperature Range | –55 to +105°C |
| Rated Voltage Range | 16 to 100V |
| Rated Capacitance Range | 6.8 to 470µF |
| Capacitance Tolerance | ±20% at 120Hz, 20°C |
| Tangent of loss angle (tan δ) | Less than or equal to the specified value at 120Hz, 20°C |
| ESR ( 1) | Less than or equal to the specified value at 100kHz, 20°C |
| Leakage Current ( 2) | Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C |
| Temperature Characteristics (Max.Impedance Ratio) | Z+105°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25 |
| Endurance | Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 3000 hours at 105°C. Leakage current ( 2) Less than or equal to the initial specified value |
| Damp Heat (Steady State) | Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 1000 hours at 60°C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value |
| Resistance to Soldering Heat | After soldering the capacitor under the soldering conditions Capacitance change Within ± 10% of the initial capacitance value ( 3) prescribed here as preheat at 150 to 200°C for 60 to 180 seconds tan δ 130% or less than the initial specified value and peak temperature at 265°C for 10 seconds or less, the ESR ( 1) 130% or less than the initial specified value capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing Leakage current ( 2) Less than or equal to the initial specified value the soldering side. |
| Marking | Navy blue print on the case top |
1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Tinned lead Wire
Resin coated Case
Capacitance

(mm)
| Size | φ8 × 9L | φ8 × 12L | φ10 × 13L |
| φD | 8.0 | 8.0 | 10.0 |
| L | 8.5 | 11.5 | 12.5 |
| P | 3.5 | 3.5 | 5.0 |
| φd | 0.6 | 0.6 | 0.6 |
Voltage
Type numbering system (Example : 35V 82µF)
1 2 3 4 5 6 7 8 9 10 11 12

| V | 16 | 2 | 0 25 | 35 | 50 63 | 80 | 100 |
| Code | C | D | E | V | H J | K | 2A |
Please refer to page 20 about the end seal configulation.
Dimension table in next page.
CAT.8100A-1
Page 2
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LVseries
Standard Ratings
| Rated Voltage (V) code | Surge Voltage (V) | Rated Capacitance (µF) | Case Size φD × L (mm) | tan δ | Leakage Current (µA) | ESR (mΩ) (at 100kHz 20°C) | Rated Ripple (mArms) | Part Number |
|---|---|---|---|---|---|---|---|---|
| 16 (1C) | 18.4 | 220 | 8 × 9 | 0.12 | 704 | 26 | 2100 | PLV1C221MCL1 |
| 270 | 8 × 12 | 0.12 | 864 | 24 | 2500 | PLV1C271MDL1 | ||
| 470 | 10 × 13 | 0.12 | 1504 | 23 | 2900 | PLV1C471MDL1 | ||
| 20 (1D) | 23.0 | 150 | 8 × 9 | 0.12 | 600 | 27 | 2000 | PLV1D151MCL1 |
| 220 | 8 × 12 | 0.12 | 880 | 25 | 2400 | PLV1D221MDL1 | ||
| 330 | 10 × 13 | 0.12 | 1320 | 24 | 2800 | PLV1D331MDL1 | ||
| 25 (1E) | 28.7 | 120 | 8 × 9 | 0.12 | 600 | 28 | 2000 | PLV1E121MCL1 |
| 150 | 8 × 12 | 0.12 | 750 | 26 | 2400 | PLV1E151MDL1 | ||
| 270 | 10 × 13 | 0.12 | 1350 | 25 | 2800 | PLV1E271MDL1 | ||
| 35 (1V) | 40.2 | 56 | 8 × 9 | 0.12 | 392 | 29 | 1900 | PLV1V560MCL1 |
| 82 | 8 × 12 | 0.12 | 574 | 27 | 2300 | PLV1V820MDL1 | ||
| 150 | 10 × 13 | 0.12 | 1050 | 26 | 2700 | PLV1V151MDL1 | ||
| 50 (1H) | 57.5 | 33 | 8 × 9 | 0.12 | 330 | 32 | 1900 | PLV1H330MCL1 |
| 39 | 8 × 12 | 0.12 | 390 | 29 | 2200 | PLV1H390MDL1 | ||
| 68 | 10 × 13 | 0.12 | 680 | 28 | 2600 | PLV1H680MDL1 | ||
| 63 (1J) | 72.4 | 22 | 8 × 9 | 0.12 | 277 | 35 | 1800 | PLV1J220MCL1 |
| 27 | 8 × 12 | 0.12 | 340 | 33 | 2100 | PLV1J270MDL1 | ||
| 47 | 10 × 13 | 0.12 | 592 | 29 | 2600 | PLV1J470MDL1 | ||
| 80 (1K) | 92 | 10 | 8 × 9 | 0.12 | 160 | 40 | 1700 | PLV1K100MCL1 |
| 12 | 8 × 12 | 0.12 | 192 | 38 | 1900 | PLV1K120MDL1 | ||
| 22 | 10 × 13 | 0.12 | 352 | 35 | 2300 | PLV1K220MDL1 | ||
| 100 (2A) | 115 | 6 .8 | 8 × 9 | 0.12 | 136 | 45 | 1600 | PLV2A6R8MCL1 |
| 10 | 8 × 12 | 0.12 | 200 | 42 | 1800 | PLV2A100MDL1 | ||
| 18 | 10 × 13 | 0.12 | 360 | 38 | 2200 | PLV2A180MDL1 |
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 20, 21, 22. Please refer to page 3 for the minimum order quantity.