PLF0E561MCO1 NICHICON
Document overview
- PDF pages: 2
Technical content
Page 1
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LF series
Radial Lead Type, Standard

Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence.
Adapted to the RoHS directive (2002/95/EC).
Specifications
| Item | Performance Characteristics |
| Category Temperature Range | –55 ~ +105°C |
| Rated Voltage Range | 2.5 ~ 16V |
| Rated Capacitance Range | 270 ~ 1000µF |
| Capacitance Tolerance | ±20% at 120Hz, 20°C |
| tan δ | Not more than value of Standard ratings at 120Hz, 20°C |
| ESR ( 1) | Not more than value of Standard ratings at 100kHz, 20°C |
| Leakage Current ( 2) | Not more than value of Standard ratings. After 2 minute's application of rated voltage. 20°C |
| Characteristics of Temperature Impedance Ratio | Z+105°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25 |
| Endurance | Capacitance change Within ± 20% of initial value ( 3) After 2000 hours' application of rated voltage tan δ 150% or less of the initial specified value at 105°C, capacitors meet the specified value ESR ( 1) 150% or less of the initial specified value for life characteristics listed at right. Leakage current ( 2) Initial specified value or less |
| Damp Heat | Capacitance change Within ± 20% of initial value ( 3) After 1000 hours' application of rated voltage tan δ 150% or less of the initial specified value at 60°C 90%RH, capacitors meet the specified value ESR ( 1) 150% or less of the initial specified value for life characteristics listed at right. Leakage current ( 2) Initial specified value or less |
| Resistance to Soldering Heat | To comply with recommended conditions for reflow soldering. Pre-heating shall be done Capacitance change Within ± 10% of initial value ( 3) at 150 ~ 200°C and for 60 ~ 180 sec. tan δ 130% or less of the initial specified value Peak temp. is 265°C, within 10 sec. ESR ( 1) 130% or less of the initial specified value Measurement for solder temperature profile shall Leakage current ( 2) Initial specified value or less be made at a point on the terminal nearest where the terminals protrude through the soldering side of PC board. |
| Marking | Navy blue print on the case top |
1 ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor. 2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the
temperature of 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 4V 560µF)
Dimensions

Silvered lead Wire


(mm)
| Size | φ8 × 9L | φ8 × 12L | φ10 × 13L |
| φD | 8.0 | 8.0 | 10.0 |
| L | 8.5 | 11.5 | 12.5 |
| P | 3.5 | 3.5 | 5.0 |
| φd | 0.6 | 0.6 | 0.6 |
Voltage
| V | 2.5 | 4 | 6.3 | 10 | 16 |
| Code | e | g | j | A | C |
Please refer to page 21 about the end seal configulation.
Dimension table in next page.
CAT.8100V
Page 2
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LF series
Standard ratings
| Rated Voltage (V) (code) | Rated Capacitance (µF) | Case Size φD×L (mm) | tan δ | Leakage Current (0.2CV)(µA) | ESR (mΩ) (at 100kHz 20˚C) | Rated ripple (mArms) | Part Number |
|---|---|---|---|---|---|---|---|
| 2.5 (0E) | 560 | 8 × 9 | 0.08 | 280 | 6 | 4800 | PLF0E561MCO1 |
| 680 | 8 × 12 | 0.08 | 340 | 6 | 5700 | PLF0E681MDO1 | |
| 820 | 8 × 9 | 0.08 | 410 | 7 | 5200 | PLF0E821MCO6 | |
| 820 | 8 × 12 | 0.08 | 410 | 6 | 6200 | PLF0E821MDO1 | |
| 1000 | 10 × 13 | 0.08 | 500 | 6 | 6500 | PLF0E102MDO1 | |
| 4 (0G) | 560 | 8 × 9 | 0.08 | 448 | 7 | 5200 | PLF0G561MCO6 |
| 560 | 8 × 12 | 0.08 | 448 | 7 | 5500 | PLF0G561MDO1 | |
| 680 | 8 × 12 | 0.08 | 544 | 6 | 6200 | PLF0G681MDO1 | |
| 820 | 10 × 13 | 0.08 | 656 | 6 | 6500 | PLF0G821MDO1 | |
| 6.3 (0J) | 470 | 8 × 9 | 0.08 | 592 | 7 | 5200 | PLF0J471MCO6 |
| 470 | 8 × 12 | 0.08 | 592 | 7 | 5500 | PLF0J471MDO1 | |
| 680 | 10 × 13 | 0.08 | 857 | 6 | 6300 | PLF0J681MDO1 | |
| 10 (1A) | 270 | 8 × 12 | 0.08 | 540 | 8 | 4900 | PLF1A271MDO1 |
| 470 | 10 × 13 | 0.08 | 940 | 7 | 5700 | PLF1A471MDO1 | |
| 16 (1C) | 270 | 8 × 12 | 0.08 | 864 | 9 | 4800 | PLF1C271MDO1 |
| 470 | 10 × 13 | 0.08 | 1504 | 9 | 5000 | PLF1C471MDO1 |
No marked, 1 will be put at 12th digit of type numbering system.
Rated Ripple (mArms) at 105°C 100kHz
: In this case, 6 will be put at 12th digit of type numbering system.
Taping specifications are given in page 24. Please refer to page 3 for the minimum order quantity.