DATASHEET SEARCH SITE

Document overview

  • PDF pages: 5

Technical content

Page 1

Parameter Rating Units
Load Voltage 800 V P
Load Current 80 mA / mA rms DC
On-Resistance (max) 55
Input Control Current 2 mA

Features

  • 7mm Separation of Output Pins
  • 800VP Blocking Voltage
  • 5000Vrms Input/Output Isolation
  • Low Drive Power Requirements
  • Arc-Free With No Snubbing Circuits
  • No EMI/RFI Generation
  • Surface Mount Package
  • Flammability Rating UL 94 V-0

Applications

  • Meters (Watt-Hour, Water, Gas)
  • Industrial Controls
  • Instrumentation
  • Multiplexers
  • Data Acquisition
  • Electronic Switching
  • I/O Subsystems
  • Medical Equipment—Patient/Equipment Isolation

DS-PLB171-R02

Single-Pole, Normally Closed

OptoMOS® Relay

Description

Specially designed to provide 7mm of separation between the two output pins, IXYS Integrated Circuits Division's PLB171 is a single-pole, normally closed (1-Form-B) Solid State Relay that uses optically coupled MOSFET technology to provide an en hanced input-to-output isolation of 5000Vrms. Its optically coupled outputs, which use the patented OptoMOS architecture, are controlled by a highly efficient infrared LED.

The PLB171 is designed to replace, and offers superior reliability over, electromechanical relays. This device provides bounce-free switching in a compact surface-mount package.

Approvals

  • UL Certified Component: File E76270
  • EN/IEC 60950 Certified Component: TUV Certificate B 13 12 82667 003

Ordering Information

Part # Description
PLB171P 6-Pin (8-Pin Body) Flatpack (50/Tube)
PLB171PTR 6-Pin (8-Pin Body) Flatpack, Tape & Reel (1000/Reel)

Pin Configuration

PDF page 1 diagram

+ Control

– Control

Switching Characteristics of Normally Closed Devices

PDF page 1 diagram

Page 2

Absolute Maximum Ratings @ 25ºC

Parameter Ratings Units
Blocking Voltage 800 V P
Reverse Input Voltage 5 V
Input Control Current Peak (10ms) 50 mA
1 A
Input Power Dissipation 1 150 mW
Total Power Dissipation 2 800 mW
ESD, Human Body Model 8 kV
Isolation Voltage, Input to Output (60 Seconds) 5000 V rms
Operational Temperature -40 to +85 °C
Storage Temperature -40 to +125 °C

1 Derate linearly 1.33 mW / ºC 2 Derate linearly 6.67 mW / ºC

Electrical Characteristics @ 25ºC

Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied.

Typical values are characteristic of the device at +25°C, and are the result of engineering evaluations. They are provided for information purposes only, and are not part of the manufacturing testing requirements.

Parameter Conditions Symbol Min Typ Max Units
Output Characteristics
Load Current Continuous 1 Peak I=0mA F I L - - 80 mA / mA rms DC
I=0mA , t=10ms F I LPK - - ±250 mA P
On-Resistance 2 I=0mA, I= 10mA F L R ON - 58 90
I=0mA, I= 80mA F L - 38 55
Off-State Leakage Current I=5mA, V=800V F L P I LEAK - - 1 A
Switching Speeds Turn-On Turn-Off I=5mA, I=80mA F L (See Timing Diagram) t on - 0.42 5 ms
t off - 0.5 5
Output Capacitance I=2mA, V=20V , f=1MHz F L DC C OUT - 8 - pF
Input Characteristics
Input Control Current to Activate 3 I=80mA L I F - 0.2 2 mA
Input Control Current to Deactivate 3 I F 50 - - A
Input Voltage Drop I=5mA F V F 0.9 1.2 1.4 V
Reverse Input Current V=5V R I R - - 10 µA
Common Characteristics
Input to Output Capacitance V =0, f=1MHz IO C IO - 3 - pF

1 Load derates linearly from 80mA @ 25oC to 59mA @85oC. 2 Measurement taken within 1 second of on-time. 3 For applications requiring high temperature operation (greater than 60oC) a minimum LED drive current of 5mA is recommended.

Timing Diagram

PDF page 2 diagram

Page 3

PERFORMANCE DATA @25ºC (Unless Otherwise Noted)\*

Turn-On Time vs. LED Forward Current

LED Forward Voltage Drop

Turn-Off Time vs. LED Forward Current

vs. Temperature

(IL=80mA)

(IL=80mA)

PDF page 3 diagram
PDF page 3 diagram
PDF page 3 diagram

LED Forward Current (mA)

LED Forward Current (mA)

Temperature (ºC)

Turn-On Time vs. Temperature

LED Current to Activate

Turn-Off Time vs. Temperature

vs. Temperature

(IL=55mA)

(IL=55mA)

PDF page 3 diagram
PDF page 3 diagram
PDF page 3 diagram

Temperature (ºC)

Temperature (ºC)

Temperature (ºC)

Load Current vs. Load Voltage

Maximum Load Current

On-Resistance vs. Temperature

(IF=0mA)

vs. Temperature

(IF=0mA)

PDF page 3 diagram
PDF page 3 diagram

-4 -3 -2 -1 0 Load Voltage (V)

Temperature (ºC)

PDF page 3 diagram

1 2 3 4

Temperature (ºC)

Output Capacitance

Typical Leakage Current

Typical Blocking Voltage

vs. Load Voltage

vs. Temperature

vs. Temperature

(IF=2mA)

PDF page 3 diagram
PDF page 3 diagram
PDF page 3 diagram

Temperature (ºC)

Temperature (ºC)

Load Voltage (VDC)

\*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department.

Page 4

Manufacturing Information

Moisture Sensitivity

All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classifies its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below.

Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability.

This product carries a Moisture Sensitivity Level (MSL) classification as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.

Device Moisture Sensitivity Level (MSL) Classifi cation
PLB171P MSL 1

ESD Sensitivity

This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.

Soldering Profile

Provided in the table below is the Classification Temperature (TC) of this product and the maximum dwell time the body temperature of this device may be above (TC - 5)ºC. The classification temperature sets the Maximum Body Temperature allowed for this device during lead-free reflow processes. For through hole devices, and any other processes, the guidelines of J-STD-020 must be observed.

Device Classifi cation Temperature (T) c Dwell Time (t) p Max Refl ow Cycles
PLB171P 260ºC 30 seconds 3

Board Wash

IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. Board washing to reduce or remove flux residue following the solder reflow process is acceptable provided proper precautions are taken to prevent damage to the device. These precautions include, but are not limited to: using a low pressure wash and providing a follow up bake cycle sufficient to remove any moisture trapped within the device due to the washing process. Due to the variability of the wash parameters used to clean the board, determination of the bake temperature and duration necessary to remove the moisture trapped within the package is the responsibility of the

user (assembler). Cleaning or drying methods that employ ultrasonic energy may damage the device and should not be used. Additionally, the device must not be exposed to flux or solvents that are Chlorine- or Fluorine-based.

Page 5

Mechanical Dimensions

PLB171P

2.286 MAX

PDF page 5 diagram

(0.090) MAX See Note 3

7.620 ± 0.254 (0.300 ± 0.010)

(0.250 ± 0.005)

0.203 ± 0.025 (0.008 ± 0.001)

(0.100 ± 0.005)

PDF page 5 diagram

2.159 ± 0.025

Notes:

(0.085 ± 0.001)

Recommended PCB Land Pattern

Leadframe to package standoff MIN=0.000

7.62

MAX=0.102

(0.30)

(0.004)

8.70 (0.3425)

0.635 ± 0.127

1.55

2.54

(0.025 ± 0.005)

(0.0610)

(0.10) 0.65 (0.0255)

  1. Coplanarity = 0.102mm (0.004”) MAX 2. Leadframe thickness does not include solder plating (1000 microinches MAX)

Dimensions

  1. Sum of package height, standoff, and coplanarity

mm

shall not exceed 2.286mm (0.090”)

(inches)

PLB171PTR Tape & Reel

PDF page 5 diagram
PDF page 5 diagram

Dimensions

K1 = 2.00

mm

User Direction of Feed

(0.079)

(inches)

NOTES: 1. All dimensions carry tolerances of EIA Standard 481-2 2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2

For additional information please visit our website at: www.ixysic.com

IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.

The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.

Specification: DS-PLB171-R02 ©Copyright 2016, IXYS Integrated Circuits Division OptoMOS® is a registered trademark of IXYS Integrated Circuits Division All rights reserved. Printed in USA. 3/18/2016