DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 18
Technical content
Datasheet sections
Features
- Efficiency up to 88%
- High switching frequency minimizes input filter requirements and reduces output capacitance
- Proprietary “Double-Clamped” ZVS Buck-Boost Topology
- Proprietary isolated magnetic feedback
- Small footprint (0.57in2) enables PCB area savings
- Very low profile (0.265in)
- On/Off Control, positive logic
- Wide trim range +10/-20%
- Temperature Monitor (TM) & Overtemperature Protection (OTP)
- Input UVLO & OVLO and output OVP
- Overcurrent protection with auto restart
- Adjustable soft-start
- 2250VDC input to output isolation
- Surface Mountable 0.87” x 0.65” x 0.265” package
Applications
- Industrial and Networking Applications
- Space Constrained Systems
- Isolated Board Level Power
Package Information
- Surface Mountable 0.87” x 0.65” x 0.265” package
- Weight = 7.8 grams Device Output Voltage IOUT Max Set Range PI3109-01-HVIZ 5V 4 to 5.5V 10A PI3106-01-HVIZ 12V 9.6 to 13.2V 4.2A
24 Volt Rev 1.4 vicorpower.com Page 3 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Order Information Part Number VIN VOUT IOUT Max Package Transport Media PI3109-01-HVIZ 18 – 36V 5V 10A 0.87” x 0.65” x 0.265” TRAY PI3106-01-HVIZ 18 – 36V 12V 4.2A 0.87” x 0.65” x 0.265” TRAY Also Available PI3101-00-HVIZ 36 – 75V 3.3V 18A 0.87” x 0.65” x 0.265” TRAY PI3105-00-HVIZ 36 – 75V 12V 5A 0.87” x 0.65” x 0.265” TRAY PI3110-01-HVIZ 41 – 57V 18V 3.3A 0.87” x 0.65” x 0.265” TRAY PI3109-00-HVMZ 16 – 50V 5V 10A 0.87” x 0.65” x 0.265” TRAY PI3106-00-HVMZ 16 – 50V 12V 4.2A 0.87” x 0.65” x 0.265” TRAY PI3111-00-HVMZ 16 – 50V 15V 3.33 0.87” x 0.65” x 0.265” TRAY
24 Volt Rev 1.4 vicorpower.com Page 4 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Absolute Maximum Ratings Name Rating +IN to –IN Max Operating Voltage -1.0 to 36VDC (operating) +IN to –IN Max Peak Voltage 45VDC (non-operating, 100ms) ENABLE to –IN -0.3 to 6.0VDC TM to –IN -0.3 to 6.0VDC TRIM/SS to –IN -0.3 to 6.0VDC +OUT to –OUT See relevant model output section Continuous Output Current See relevant model output section Peak Output Current See relevant model output section Operating Junction Temperature -40 to 125°C Storage Temperature -50 to 125°C Case Temperature During Reflow 245°C
24 Volt Rev 1.4 vicorpower.com Page 5 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Functional Block Diagram TRIM/SS +OUT SGND -OUT -IN +IN ENABLE TM LFF RSS CSS INT VREF 1.22V RFB1 CFB1 CFB2 + Error Amp Driver DC Slow Current Limit Driver Synchronous Rectifier DC Output OVP DC Input UVP Input OVP DC DC Fast Current Limit Over Temp DC ENB Period Ramp DC Enable +DC On-Duty Ramp ZVS POWER TRAIN -DC Timing Logic FB FB ENB +5V EA Fault DC 120us delay 120us delay Fault Latch And Reset Logic Reset Fault RUN BIAS START BIAS Vcc Temp Sensor ZVS POWER TRAIN ZVS FB TRIM/SS +OUT SGND -OUT -IN +IN ENABLE TM LFF RSS CSS INT VREF 1.22V RFB1 CFB1 CFB2 + Error Amp Driver DC Slow Current Limit Driver Synchronous Rectifier DC Output OVP DC Input UVP Input OVP DC DC Fast Current Limit Over Temp DC ENB Period Ramp DC Enable +DC On-Duty Ramp ZVS POWER TRAIN -DC Timing Logic FB FB ENB +5V EA Fault DC 120us delay 120us delay Fault Latch And Reset Logic Reset Fault RUN BIAS START BIAS Vcc Temp Sensor ZVS POWER TRAIN ZVS FB
24 Volt Rev 1.4 vicorpower.com Page 6 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Package Pin-Out Pin Description U.S. PATS. LISTED ON PACKING MATERIALS & DATASHEETS MADE IN USA DC-DC Converter +IN -IN +OUT -OUT SGND TM TRIM/SS ENABLE Pin Name Description +IN Primary side positive input voltage terminals. –IN Primary side negative input voltage terminals. ENABLE Converter enable option, functions as 5V reference and on / off control pin. Pull low for off. TRIM/SS External soft start pin and trim function. Connect to SGND or ENABLE through resistor for trim up or trim down. TM Temperature measurement output pin. SGND Signal ground, primary side referenced. +OUT Isolated secondary DC output voltage positive terminals. –OUT Isolated secondary DC output voltage negative terminals.
24 Volt Rev 1.4 vicorpower.com Page 7 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Unless otherwise specified: 18V < VIN < 36V, 0A < IOUT < 10A, -40°C < TCASE < 100°C [1] [1] These parameters are not production tested but are guaranteed by design, characterization and correlation with statistical process control. Unless otherwise specified, ATE tests are completed at room temperature. [2] Current flow sourced by a pin has a negative sign. Parameter Symbol Conditions Min Typ Max Unit Input Specifications Input Voltage Range VIN 18 24 36 VDC Input dV/dt [1] VINDVDT VIN = 36V 1.0 V/µs Input Undervoltage Turn-on VUVON IO = 10A 16.2 17.0 17.8 VDC Input Undervoltage Turn-off VUVOFF IO = 10A 15.1 16.0 16.7 VDC Input Undervoltage Hysteresis VUVH IO = 10A 1.0 VDC Input Overvoltage Turn-on VOVON IO = 10A 37.8 40.0 41.7 VDC Input Overvoltage Turn-off VOVOFF IO = 10A 38.6 40.7 42.6 VDC Input Overvoltage Hysteresis VOVH IO = 10A 0.7 VDC Input Quiescent Current IQ VIN = 24V, ENABLE = 0V 2 mADC Input Idling Power PIDLE VIN = 24V, IOUT = 0A 2.8 W Input Standby Power PSBY VIN = 24V, ENABLE = 0V 0.048 W Input Current Full Load IIN TCASE = 100°C, IOUT = 10A, ηFL = 88.0% typical, VIN = 24V 2.36 ADC Input Reflected Ripple Current IINRR LIN = 0.47µH CIN = 100µF 63V electrolytic + 2 x 4.7µF 50V X7R ceramic 13 mApp Recommended Ext Input Capacitance CIN CIN = 100µF 50V electrolytic + 2 x 4.7µF 50V X7R ceramic CIN = Cbulk + Chf 109.4 µF Output Specifications Output Voltage Set Point VOUT IOUT = 5A 5.0 VDC Total Output Accuracy VOA -0ºC < TCASE < 100ºC -3 +3 % -40ºC < TCASE < 0ºC -4 +3 % Output Voltage Trim Range VOADJ -20 10 % Output Current Range IOUT 10 ADC Overcurrent Protection IOCP 10.8 15 20 ADC Efficiency – Full Load ηFL TCASE = 100ºC, VIN = 24V 86.0 88.0 % Efficiency – Half Load ηHL TCASE = 100ºC, VIN = 24V 83.5 85.5 % Output OVP Set Point VOVP 6 6.3 6.6 VDC Output Ripple Voltage VORPP COUT = 6 x 10µF 10V X7R DC-20MHz 140 mVpp Switching Frequency fSW 900 kHz Output Turn-on Delay Time tONDLY VIN = VUVON to ENABLE = 5V 80 ms Output Turn-off Delay Time tOFFDLY VIN = VUVOFF to ENABLE < 1.8V 10 µs Soft-Start Ramp Time tSS ENABLE = 5V to 90% VOUT CREF = 0 230 µs Maximum Load Capacitance COUT CREF = 0.39µF, COUT = Al Electrolytic 4700 µF Load Transient Deviation VODV IOUT = 25% step 0.1A/µS COUT = 6 x 10µF 10V X7R 120 mV Load Transient Recovery Time tOVR IOUT = 25% step 0.1A/µS COUT = 6 x 10µF 10V X7R VOUT - 1% 100 µs Maximum Output Power POUT 50 W Absolute Maximum Output Ratings Name Rating +OUT to –OUT -0.5V to 6.8VDC Continuous Output Current 10ADC Peak Output Current 20ADC
24 Volt Rev 1.4 vicorpower.com Page 8 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ [1] These parameters are not production tested but are guaranteed by design, characterization and correlation with statistical process control. Unless otherwise specified, ATE tests are completed at room temperature. [2] Current flow sourced by a pin has a negative sign. Parameter Symbol Conditions Min Typ Max Unit ENABLE DC Voltage Reference Output VERO 4.65 4.9 5.15 VDC Output Current Limit [2] IECL ENABLE = 3.3V -3.3 -2.6 -1.9 mADC Start Up Current Limit [2] IESL ENABLE = 1V -120 -90 -60 µA Module Enable Voltage VEME 1.95 2.5 3.05 VDC Module Disable Voltage VEMD 1.8 2.35 2.9 VDC Disable Hysteresis VEDH 150 mV Enable Delay Time tEE 10 µs Disable Delay Time tED 10 µs Maximum Capacitance CEC 1500 pF Maximum External Toggle Rate fEXT 1 Hz TRIM/SS Trim Voltage Reference VREF 1.232 VDC Internal Capacitance CREFI 10 nF External Capacitance CREF 0.39 µF Internal Resistance RREFI 10 kΩ TM (Temperature Monitor) Temperature Coefficient [1] TMTC 10 mV/ºK Temperature Full Range Accuracy [1] TMACC -5 5 ºK Drive Capability ITM -100 µA TM Output Setting VTM Ambient Temperature = 300ºK 3.00 V Thermal Specification Junction Temperature Shutdown [1] TMAX 130 135 140 ºC Junction-to-Case Thermal Impedance RΘJ-C 3 ºC/W Case-to-Ambient Thermal Impedance RΘC-A Mounted on 9in2 1oz. Cu 6 layer PCB 25°C 9.6 ºC/W Regulatory Specification IEC 60950-1:2005 (2nd Edition) EN 60950-1:2006 IEC 61000-4-2 UL60950-1:2007 CAN/CSA C22.2 NO. 60950-1-07 Recommended Input Fuse Rating IFUSE Fast acting LITTLEFUSE Nano2 Series Fuse 4 10 A
24 Volt Rev 1.4 vicorpower.com Page 11 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Unless otherwise specified: 18V < VIN < 36V, 0A < IOUT < 4.2A, -40°C < TCASE < 100°C [1] [1] These parameters are not production tested but are guaranteed by design, characterization and correlation with statistical process control. Unless otherwise specified, ATE tests are completed at room temperature. [2] Current flow sourced by a pin has a negative sign. Parameter Symbol Conditions Min Typ Max Unit Input Specifications Input Voltage Range VIN 18 24 36 VDC Input dV/dt [1] VINDVDT VIN = 36V 1.0 V/µs Input Undervoltage Turn-on VUVON IO = 4.2A 16.2 17.0 17.8 VDC Input Undervoltage Turn-off VUVOFF IO = 4.2A 15.1 15.9 16.7 VDC Input Undervoltage Hysteresis VUVH IO = 4.2A 1.1 VDC Input Overvoltage Turn-on VOVON IO = 4.2A 37.8 39.6 41.7 VDC Input Overvoltage Turn-off VOVOFF IO = 4.2A 38.6 40.6 42.6 VDC Input Overvoltage Hysteresis VOVH IO = 4.2A 1.0 VDC Input Quiescent Current IQ VIN = 24V, ENABLE = 0V 2 mADC Input Idling Power PIDLE VIN = 24V, IOUT = 0A 3.3 W Input Standby Power PSBY VIN = 24V, ENABLE = 0V 0.048 W Input Current Full Load IIN TCASE = 100°C, IOUT = 4.2A, ηFL = 88.2% typical, VIN = 24V 2.38 ADC Input Reflected Ripple Current IINRR LIN = 0.47µH CIN = 100µF 63V electrolytic + 2 x 4.7µF 50V X7R ceramic 13 mApp Recommended Ext Input Capacitance CIN CIN = 100µF 50V electrolytic + 2 x 4.7µF 50V X7R ceramic CIN = Cbulk + Chf 109.4 µF Output Specifications Output Voltage Set Point VOUT IOUT = 2.1A 12.0 VDC Total Output Accuracy VOA -0ºC < TCASE < 100ºC -3 +3 % -40ºC < TCASE < 0ºC -4 +3 % Output Voltage Trim Range VOADJ -20 10 % Output Current Range IOUT 4.2 ADC Overcurrent Protection IOCP 4.6 5.4 12 ADC Efficiency – Full Load ηFL TCASE = 100ºC, VIN = 24V 86.2 88.2 % Efficiency – Half Load ηHL TCASE = 100ºC, VIN = 24V 83.5 85.5 % Output OVP Set Point VOVP 13.8 14.5 15.3 VDC Output Ripple Voltage VORPP COUT = 6 x 2.2µF 16V X7R DC-20MHz 120 mVpp Switching Frequency fSW 900 kHz Output Turn-on Delay Time tONDLY VIN = VUVON to ENABLE = 5V 80 ms Output Turn-off Delay Time tOFFDLY VIN = VUVOFF to ENABLE < 1.8V 10 µs Soft-Start Ramp Time tSS ENABLE = 5V to 90% VOUT CREF = 0 230 µs Maximum Load Capacitance COUT CREF = 0.39µF, COUT = Al Electrolytic 2200 µF Load Transient Deviation VODV IOUT = 50% step 0.1A/µS COUT = 6 x 2.2µF 16V X7R 360 mV Load Transient Recovery Time tOVR IOUT = 50% step 0.1A/µS COUT = 6 x 2.2µF 16V X7R VOUT - 1% 100 µs Maximum Output Power POUT 50 W Absolute Maximum Output Ratings Name Rating +OUT to –OUT -0.5V to 16VDC Continuous Output Current 4.2ADC Peak Output Current 12ADC
24 Volt Rev 1.4 vicorpower.com Page 12 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ [1] These parameters are not production tested but are guaranteed by design, characterization and correlation with statistical process control. Unless otherwise specified, ATE tests are completed at room temperature. [2] Current flow sourced by a pin has a negative sign. Parameter Symbol Conditions Min Typ Max Unit ENABLE DC Voltage Reference Output VERO 4.65 4.9 5.15 VDC Output Current Limit [2] IECL ENABLE = 3.3V -3.3 -2.6 -1.9 mADC Start Up Current Limit [2] IESL ENABLE = 1V -120 -90 -60 µA Module Enable Voltage VEME 1.95 2.5 3.05 VDC Module Disable Voltage VEMD 1.8 2.35 2.9 VDC Disable Hysteresis VEDH 150 mV Enable Delay Time tEE 10 µs Disable Delay Time tED 10 µs Maximum Capacitance CEC 1500 pF Maximum External Toggle Rate fEXT 1 Hz TRIM/SS Trim Voltage Reference VREF 1.233 VDC Internal Capacitance CREFI 10 nF External Capacitance CREF 0.39 µF Internal Resistance RREFI 10 kΩ TM (Temperature Monitor) Temperature Coefficient [1] TMTC 10 mV/ºK Temperature Full Range Accuracy [1] TMACC -5 5 ºK Drive Capability ITM -100 µA TM Output Setting VTM Ambient Temperature = 300ºK 3.00 V Thermal Specification Junction Temperature Shutdown [1] TMAX 130 135 140 ºC Junction-to-Case Thermal Impedance RΘJ-C 3 ºC/W Case-to-Ambient Thermal Impedance RΘC-A Mounted on 9in2 1oz. Cu 6 layer PCB 25°C 9.18 ºC/W Regulatory Specification IEC 60950-1:2005 (2nd Edition) EN 60950-1:2006 IEC 61000-4-2 UL60950-1:2007 CAN/CSA C22.2 NO. 60950-1-07 Recommended Input Fuse Rating IFUSE Fast acting LITTLEFUSE Nano2 Series Fuse 4 10 A
24 Volt Rev 1.4 vicorpower.com Page 16 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ TM The TM pin serves as an output indicator of the internal package temperature which is within +/-5°K of the hottest junction temperature. Because of this, it is a good indicator of a thermal overload condition. The output is a scaled, buffered analog voltage which indicates the internal temperature in degrees Kelvin. Upon a thermal overload, the TM pin is pulled low, indicating a thermal fault has occurred. Upon restart of the converter, the TM pin reverts back to a buffered monitor. The thermal shutdown function of the PI31xx-01-HVIZ is a fault feature which interrupts power processing if a certain maximum temperature is exceeded. TM can be monitored by an external microcontroller or circuit configured as an adaptive fan speed controller so that air flow in the system can be conveniently regulated. SGND The PI31xx-01-HVIZ SGND pin is the “quiet” control circuitry return. It is basically an extension of the internal signal ground. To avoid contamination and potential ground loops, this ground should NOT be connected to -IN since it is already star connected inside the package. Connect signal logic to SGND. Output Power Pins +OUT And -OUT The output power terminals OUT(+) and OUT(-) deliver the maximum output current from the PI31xx-01-HVIZ through the J-lead output pins. This configuration allows for a low impedance output and should be connected to multi-layer PCB parallel planes for best performance. Due to the high switching frequency, output ripple and noise can be easily attenuated by adding just a few high quality X7R ceramic capacitors while retaining adequate transient response for most applications. The PI31xx-01-HVIZ does not require any feedback loop compensation nor does it require any opto-isolation. All isolation is contained within the package. This greatly simplifies the use of the converter and eliminates all outside influences of noise on the quality of the output voltage regulation and feedback loop. It is important for the user to minimize resistive connections from the load to the converter output and to keep stray inductance to a minimum for best regulation and transient response. The very small size footprint and height of the PI31xx-01-HVIZ allows the converter to be placed in the optimum location to allow for tight connections to the point of load. For those applications absolutely requiring very tight regulation, contact Picor Engineering at vicorpower.com for a remote sense application circuit which can be used.
24 Volt Rev 1.4 vicorpower.com Page 17 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Package Outline & Recommended PCB Land Pattern Figure 23 — Package Outline & Recommended PCB Land Pattern
24 Volt Rev 1.4 vicorpower.com Page 18 of 18 02/2015 800 927.9474 PI31xx-01-HVIZ Vicor’s comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. Vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. Information published by Vicor has been checked and is believed to be accurate at the time it was printed; however, Vicor assumes no responsibility for inaccuracies. Testing and other quality controls are used to the extent Vicor deems necessary to support Vicor’s product warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. Specifications are subject to change without notice. Vicor’s Standard Terms and Conditions All sales are subject to Vicor’s Standard Terms and Conditions of Sale, which are available on Vicor’s webpage or upon request. Product Warranty In Vicor’s standard terms and conditions of sale, Vicor warrants that its products are free from non-conformity to its Standard Specifications (the “Express Limited Warranty”). This warranty is extended only to the original Buyer for the period expiring two (2) years after the date of shipment and is not transferable. UNLESS OTHERWISE EXPRESSLY STATED IN A WRITTEN SALES AGREEMENT SIGNED BY A DULY AUTHORIZED VICOR SIGNATORY, VICOR DISCLAIMS ALL REPRESENTATIONS, LIABILITIES, AND WARRANTIES OF ANY KIND (WHETHER ARISING BY IMPLICATION OR BY OPERATION OF LAW) WITH RESPECT TO THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, INFRINGEMENT OF ANY PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY RIGHT, OR ANY OTHER MATTER. This warranty does not extend to products subjected to misuse, accident, or improper application, maintenance, or storage. Vicor shall not be liable for collateral or consequential damage. Vicor disclaims any and all liability arising out of the application or use of any product or circuit and assumes no liability for applications assistance or buyer product design. Buyers are responsible for their products and applications using Vicor products and components. Prior to using or distributing any products that include Vicor components, buyers should provide adequate design, testing and operating safeguards. Vicor will repair or replace defective products in accordance with its own best judgment. For service under this warranty, the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping instructions. Products returned without prior authorization will be returned to the buyer. The buyer will pay all charges incurred in returning the product to the factory. Vicor will pay all reshipment charges if the product was defective within the terms of this warranty. Life Support Policy VICOR’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF VICOR CORPORATION. As used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Per Vicor Terms and Conditions of Sale, the user of Vicor products and components in life support applications assumes all risks of such use and indemnifies Vicor against all liability and damages. Intellectual Property Notice Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending patent applications) relating to the products described in this data sheet. No license, whether express, implied, or arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Interested parties should contact Vicor’s Intellectual Property Department. The products described on this data sheet are protected by the following U.S. Patents Numbers: RE 40,072 Vicor Corporation
25 Frontage Road
Andover, MA 01810 USA Picor Corporation
51 Industrial Drive
North Smithfield, RI 02896 USA email Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com