DATASHEET SEARCH SITE
Document overview
- PDF pages: 18
Technical content
Page 1
PI3101
Cool-PowerTM Series
36-75V Input, 3.3V / 18A / 60W Output
Very High Density Isolated DC-DC Converter (400W/in3)
Description
The Cool-PowerTM PI3101 is a very high density isolated DC-DC converter implementing a high efficiency soft-switching power architecture. The PI3101 operates over a wide range input of 36V to 75Vdc, delivering ~60W of output power (3.3Vout @ 18A), yielding an unprecedented power density of 400W/in3. The PI3101 is available in a space saving surface mountable 0.87” x 0.65” x 0.265” package, achieving ~50% space reduction versus conventional solutions.
The switching frequency of 900kHz allows for small input and output filter components which further reduces the total size and cost of the overall system solution. The output voltage is sensed and fed back to the internal controller using a proprietary isolated magnetic feedback scheme which allows for high bandwidth and good common mode noise immunity. The PI3101 requires no external feedback compensation and offers a total solution with a minimum number of external components. A rich feature set is offered, including output voltage trim capability, output over-voltage protection, adjustable soft-start, over-current protection with auto-restart, over and under input voltage lockout and a
temperature monitoring and protection function that provides an analog voltage proportional to the die temperature as shut down and alarm capabilities.

PI3101-00-HVIZ
36-75Vin, 3.3Vout, 18A Very High Density Isolated DC-DC Converter
Features
Efficiency up to 87% High switching frequency minimizes input filter requirements and reduces output capacitance Proprietary “Double-Clamped” ZVS Buck-Boost Topology Proprietary isolated magnetic feedback Small footprint (0.57 in2) enables PCB area savings Very low profile (0.265 in) Wide input voltage range operation (36-75Vdc) On/Off Control, positive logic +10/-10% Trim Temperature Monitor (TM) & Over-Temperature Protection (OTP) Input UVLO & OVLO and output OVP Over current protection with auto restart Adjustable soft-start 2250V input to output isolation
Applications
Power Over Ethernet (PoE) Communications Telecom Systems Network Power
Package Information
Surface Mountable 0.87” x 0.65” x 0.265” package
Typical Application Schematic Diagram

Figure 1 Picor PI3101 Shown With System Fuse, Filter, Decoupling And Extended Soft Start
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 1 of 18
Page 2
Pin Description And Maximum Ratings

TRIM/SS
ENABLE
Figure 2 Picor PI3101-00-HVIZ Pin Out
Pin Description
| Pin Name | Description |
|---|---|
| +IN | Primary side positive input voltage terminals. |
| -IN | Primary side negative input voltage terminals. |
| ENABLE | Converter enable option, functions as 5V reference and on/off control pin. Pull low for off. |
| TRIM/SS | External soft start pin and trim function. Connect to SGND or ENABLE through resistor for trim up or trim down. |
| TM | Temperature measurement output pin. |
| SGND | Signal ground, primary side referenced. |
| +OUT | Isolated secondary DC output voltage positive terminals. |
| -OUT | Isolated secondary DC output voltage negative terminals. |
Absolute Maximum Ratings
| +IN to -IN Max Operating Voltage | -1.0 to 75Vdc (operating) |
|---|---|
| +IN to -IN Max Peak Voltage | 100Vdc (non-operating, 100ms) |
| ENABLE to –IN | -0.3 to 6.0Vdc |
| TM to –IN | -0.3 to 6.0Vdc |
| TRIM/SS to –IN | -0.3 to 6.0Vdc |
| +OUT to –OUT | -0.5 to 6.0Vdc |
| Isolation Voltage (+IN/-IN to +OUT/-OUT) | 2250Vdc |
| Isolation Capacitance (+IN/-IN to +OUT/-OUT) | 330pF |
| Continuous Output Current | 18A DC (Tcase < 100°C) |
| Peak Output Current | 34Adc (11mm heatsink, 600LFM) |
| Operating Junction Temperature | -40 to 125°C |
| Storage Temperature | -40 to 125°C |
| Case Temperature During Reflow | 245°C |
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 2 of 18
Page 3
Functional Block Diagram

Figure 3 PI3101 Functional Block Diagram
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 3 of 18
Page 4
Electrical Specifications
Unless otherwise specified: 36V < VIN < 75V, 0A < IOUT < 18A, -40C < TCASE < 100C(1)
| Parameter | Symbol | Min | Typ | Max | Units | Conditions |
|---|---|---|---|---|---|---|
| Input Specifications | ||||||
| Input Voltage Range | V IN | 36 | 48 | 75 | Vdc | |
| Input dv/dt (1) | V INDVDT | 1.0 | V/µs | V = 75V IN | ||
| Input Under-Voltage Turn-on | V UVON | 32.5 | 34 | 35 | Vdc | I = 1.8A O |
| Input Under-Voltage Turn-off | V UVOFF | 30.5 | 32 | 33 | Vdc | I = 1.8A O |
| Input Under-Voltage Hysteresis | V UVH | 2 | Vdc | I = 1.8A O | ||
| Input Over-Voltage Turn-on | V OVON | 75.7 | 78 | 81 | Vdc | I = 1.8A O |
| Input Over-Voltage Turn-off | V OVOFF | 77.7 | 80 | 82.3 | Vdc | I = 1.8A O |
| Input Over-Voltage Hysteresis | V OVH | 2 | I = 1.8A O | |||
| Input Quiescent Current | I Q | 2.5 | mAdc | V = 48V, ENABLE = 0V IN | ||
| Input Idling Power | P IDLE | 4.0 | W | V = 48V, I = 0A IN OUT | ||
| Input Standby Power | P SBY | 0.225 | W | V = 48V, ENABLE = 0V IN | ||
| Input Current Full Load | I IN | 1.4 | Adc | T = 100C I = 18A = CASE OUT FL 86.5% typical V =48V IN | ||
| Input Reflected Ripple Current | I INRR | 10 | mApp | L = 2µH C = 47µF 100V IN IN electrolytic + 2x1µF 100V X7R ceramic | ||
| Recommended Ext Input Capacitance | C IN | 49 | µF | C = 47µF 100V electrolytic + IN 2x1µF 100V X7R ceramic C = Cbulk + Chf IN | ||
| Output Specifications | ||||||
| Output Voltage Set Point | V OUT | 3.3 | Vdc | I = 9A OUT | ||
| Total Output Accuracy | V OA | -3 | +3 | % | ||
| Line Regulation | V RLI | 0.25 | % | V = 36V-75V, I = 18A IN OUT | ||
| Load Regulation | V RLO | 1.5 | % | V = 48V, I = 0-18A IN OUT | ||
| Output Voltage Trim Range | V OADJ | -10% | 10% | % | ||
| Output Current Range | I OUT | 18 | Adc | |||
| Over Current Protection | I OCP | 18.8 | 26 | 33 | Adc | |
| Efficiency – Full Load | FL | 84.5 | 86.5 | % | T = 100C, V =48V CASE IN | |
| Efficiency – Half Load | HL | 84.5 | % | T = 100C, V =48V CASE IN | ||
| Output OVP Set Point | V OVP | 4.1 | Vdc | |||
| Output Ripple Voltage | V ORPP | 75 | mVpp | C = 12x10µF 10V X7R DC- OUT 20MHz using PI3101-EVAL1 | ||
| Switching Frequency | f SW | 900 | kHz | |||
| Output Turn-on Delay Time | t ONDLY | 80 | ms | V = V to ENABLE = 5V IN UVON | ||
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 4 of 18
Page 5
Electrical Specifications (continued) Unless otherwise specified: 36V < VIN < 75V, 0A < IOUT < 18A, -40C < TCASE < 100C(1)
| Parameter | Symbol | Min | Typ | Max | Units | Conditions |
|---|---|---|---|---|---|---|
| Output Specifications (continued) | ||||||
| Output Turn-off Delay Time | t OFFDLY | 10 | µs | V = V to ENABLE < 1.8V IN UVOFF | ||
| Soft-Start Ramp Time | t SS | 380 | µs | ENABLE = 5V to 90% Vout C = 0 SS | ||
| Maximum Load Capacitance | C OUT | 10 | mF | V = 75V, 18A resistive load IN C = 1µF SS | ||
| Load Transient Deviation | V ODV | 90 | 110 | mV | I = 25% step 0.1A/µS OUT C = 12x10µF 10V X7R OUT | |
| Load Transient Recovery Time | t OVR | 120 | µs | I = 25% step 0.1A/µS OUT C = 12x10µF 10V X7R OUT V - 1% OUT | ||
| Maximum Output Power | P OUT | 60 | W | |||
| Auxiliary Control Pins | ||||||
| ENABLE | ||||||
| DC Voltage Reference Output | V ERO | 4.65 | 4.9 | 5.15 | Vdc | |
| Output Current Limit (2) | I ECL | -3.3 | -2.6 | -1.9 | mAdc | ENABLE = 3.3V |
| Start Up Current Limit (2) | I ESL | -120 | -90 | -60 | µA | ENABLE = 1V |
| Module Enable Voltage | V EME | 1.95 | 2.5 | 3.05 | Vdc | |
| Module Disable Voltage | V EMD | 1.8 | 2.35 | 2.9 | Vdc | |
| Disable Hysteresis | V EDH | 150 | mV | |||
| Enable Delay Time | t EE | 10 | µs | |||
| Disable Delay Time | t ED | 10 | µs | |||
| Maximum Capacitance | C EC | 1500 | pF | |||
| Maximum External Toggle Rate | f EXT | 1 | Hz | |||
| TRIM/SS | ||||||
| Trim Voltage Reference | V REF | 1.22 | Vdc | |||
| Internal Capacitance | C REFI | 100 | nF | |||
| External Capacitance | C REF | 1 | µF | |||
| Internal Resistance | R REFI | 10 | k | |||
| TM (Temperature Monitor) | ||||||
| Temperature Coefficient | TM TC | 10 | mV/°K | |||
| Temperature Full Range Accuracy | TM ACC | -5 | 5 | °K | ||
| Drive Capability | I TM | -100 | µA | |||
| TM Output Setting | V TM | 3.00 | V | Ambient Temperature = 300°K | ||
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 5 of 18
Page 6
Electrical Specifications (continued) Unless otherwise specified: 36V < VIN < 75V, 0A < IOUT < 18A, -40C < TCASE < 100C(1)

Mechanical Specifications
| Parameter | Symbol | Min | Typ | Max | Units | Conditions |
|---|---|---|---|---|---|---|
| Mechanical Parameters | ||||||
| PI3101 Package Weight | M PKG | 7.2 | g | No heat sink | ||
| PI3101 Package Length | L PKG | 2.2 | cm | No heat sink | ||
| 0.87 | ins | No heat sink | ||||
| PI3101 Package Width | W PKG | 1.65 | cm | No heat sink | ||
| 0.65 | ins | No heat sink | ||||
| PI3101 Package Height | H PKG | 0.673 | cm | No heat sink | ||
| 0.265 | ins | No heat sink | ||||
Note (1): These parameters are not production tested but are guaranteed by design, characterization and correlation with statistical process control. Unless otherwise specified, ATE tests are completed at room temperature.
Note (2): Current flow sourced by a pin has a negative sign.
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 6 of 18
Page 7
Functional Description:
Input Power Pins IN(+) and IN(-):
The input power pins on the PI3101 are connected to the input power source which can range from 36V to 75V DC. Under surge conditions, the PI3101 can withstand up to 100V DC for 100ms without incurring damage. The user should take care to avoid driving the input rails above the specified ratings. Since the PI3101 is designed with high reliability in mind, the input pins are continuously monitored. If the applied voltage exceeds the input over-voltage trip point (typically 80V) the conversion process shall be terminated immediately. The converter initiates softstart automatically within 80ms after the input voltage is reduced back to the appropriate value.
The input pins do not have reverse polarity protection. If the PI3101 is operated in an environment where reverse polarity is a concern, the user should consider using a polarity protection device such as a suitably rated diode. To avoid the high losses of using a diode, the user should consider the much higher efficiency Picor family of intelligent Cool-ORingTM solutions that can be used in reverse polarity applications. Information is available at picorpower.com. The PI3101 will draw nearly zero current until the input voltage reaches the internal start up threshold. If the ENABLE pin is not pulled low by external circuitry, the output voltage will begin rising to its
final value of 3.3V about 80ms after the input UV lockout releases. This will occur automatically even if the ENABLE pin is floating. To help keep the source impedance low, the input to the PI3101 should be bypassed with (2) 1uF 100V ceramic capacitors of X7R dielectric in parallel with a low Q 47uF 100V electrolytic capacitor. To reduce EMI and reflected ripple current, a series inductor of 2 to 4.7uH can be added. The input traces to the module should be low impedance configured in such a manner as to keep stray inductance minimized. ENABLE Pin: The ENABLE pin serves as a multi-function pin for the PI3101. During normal operation, it outputs the on-board 4.9V regulator which can be used for
trimming the module up. The ENABLE pin can also be used as a remote enable pin either from the secondary via an optocoupler and some external isolated bias supply or from the primary side through a small signal transistor, FET or any device that sinks 3.3mA, minimum. If the ENABLE pin is lower than 2.35V typical, the converter will be held off or shut down if already operating. A third feature is
offered in that during a fault condition such as output OVP, input UV or OV, or output current limit, the ENABLE pin is pulled low internally. This can be used as a signal to the user that a fault has occurred. Whenever the ENABLE pin is pulled low, the TRIM/SS pin follows, resetting the internal and external soft-start circuitry. All faults will pull ENABLE low including over temperature. If increased turn on delay is desired, the ENABLE pin can be bypassed with a small capacitor up to a maximum of 1500pF. TRIM/SS Pin: The TRIM/SS pin serves as another multi-purpose pin. First, it is used as the reference for the internal error amplifier. Connecting a resistor from TRIM/SS
to SGND allows the reference to be margined down by as much as 10%. Connecting a resistor from TRIM/SS to ENABLE will allow the reference and output voltage to be margined up by 10%. If the user wishes a longer start up time, a small ceramic capacitor can be added to TRIM/SS to increase it. It is critical to connect any device between TRIM/SS and SGND and not -IN, otherwise high frequency noise will be introduced to the reference and possibly cause erratic operation. TM Pin: The TM pin serves as an output indicator of the internal package temperature which is within approximately +/- 5 K of the hottest junction temperature. Because of this, it is a good indicator of
a thermal overload condition. The output is a scaled, buffered analog voltage which indicates the internal temperature in degrees Kelvin. Upon a thermal overload, the TM pin is pulled low, indicating a thermal fault has occurred. Upon restart of the converter, the TM pin reverts back to a buffered monitor. The thermal shutdown function of the PI3101 is a fault feature which interrupts power processing if a certain maximum temperature is exceeded. TM can be monitored by an external microcontroller or circuit configured as an adaptive fan speed controller so that air flow in the system can be conveniently regulated. SGND Pin: The PI3101 SGND pin is the “quiet” control circuitry
return. It is basically an extension of the internal signal ground. To avoid contamination and potential ground loops, this ground should NOT be connected to -IN since it is already star connected inside the package. Connect signal logic to SGND, not -IN.
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 7 of 18
Page 8
Output Power Pins +OUT And -OUT:
The output power terminals OUT(+) and OUT(-) deliver the 18A maximum output current from the PI3101 through the J-lead output pins. This configuration allows for a low impedance output and should be connected to multi-layer PCB parallel planes for best performance. Due to the high switching frequency, output ripple and noise can be easily attenuated by adding just a few high quality X7R ceramic capacitors while retaining adequate transient response for most applications. The PI3101 does not require any feedback loop compensation nor does it require any opto-isolation. All isolation is contained within the package. This greatly simplifies the use of the converter and
eliminates all outside influences of noise on the quality of the output voltage regulation and feedback loop. It is important for the user to minimize resistive connections from the load to the converter output and to keep stray inductance to a minimum for best regulation and transient response. The very small size footprint and height of the PI3101 allows the converter to be placed in the optimum location to allow for tight connections to the point of load. For those applications absolutely requiring very tight regulation, contact Picor Engineering at picorpower.com for a remote sense application circuit which can be used.
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 8 of 18
Page 9
Typical Performance Characteristics:

Figure 4 Conversion Efficiency (Tcase = 100C)


Figure 6 Power Dissipation Vs Temp (No Heat Sink)

PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 9 of 18
Page 10
Typical Performance Characteristics:


Figure 10 RC-A (No Heat Sink Longitudinal Flow)


Figure 11 RC-A ( Heat Sinks Longitudinal Flow)

Figure 12 Thermal Image VIN = 48V IO = 18A Flow = 600LFM Longitudinal No Heat Sink Temp = 25°C
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 10 of 18
Page 11
Typical Performance Characteristics:

Figure 13 RC-A (No Heat Sink Transverse Flow)


106.3°C
100
80
60
40
Figure 15 Thermal Image VIN = 48V IO = 18A Flow = 600LFM X-Flow No Heat Sink Temp = 25°C

Figure 16 Output Ripple
(VIN = 48V IO = 18A COUT = 12X10µF X7R Ceramic)

Figure 17 Transient Response 0.1A/µs (VIN = 48V IOUT = 4.5-9A COUT = 12X10µF X7R Ceramic)

Figure 18 Transient Response 0.1A/µs (VIN = 48V IOUT = 9-4.5A COUT = 12X10µF X7R Ceramic)
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 11 of 18
Page 12
Typical Performance Characteristics:

Figure 19 Transient Response 0.1A/µs (VIN = 48V IOUT = 9-13.5A COUT = 12X10µF X7R Ceramic)

Figure 20 Transient Response 0.1A/µs (VIN = 48V IOUT = 9-13.5A COUT = 12X10µF X7R Ceramic)

Figure 21 Output OVP Forced Via TRIM Pin (VIN = 48V IOUT = 9A COUT = 12X10µF X7R Ceramic)

Figure 22 Start Up VIN Vs VOUT (VIN = 36V IOUT = 9A COUT = 12X10µF X7R Ceramic)

Figure 23 Start Up VIN Vs VOUT (VIN = 48V IOUT = 18A COUT = 12X10µF X7R Ceramic)

Figure 24 Start Up VIN Vs VOUT (VIN = 75V IOUT = 9A COUT = 12X10µF X7R Ceramic)
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 12 of 18
Page 13
Typical Performance Characteristics:

Figure 25 Start Up VIN Vs VOUT (VIN = 75V IOUT = 18A COUT = 12X10µF X7R Ceramic)

Figure 26 Start Up ENABLE Vs VOUT (VIN = 36V IOUT = 18A COUT = 12X10µF X7R Ceramic)

Figure 27 Shut Down ENABLE Vs VOUT (VIN = 36V IOUT = 18A COUT = 12X10µF X7R Ceramic)

Figure 28 Shut Down VIN Vs VOUT (VIN = 48V IOUT = 18A COUT = 12X10µF X7R Ceramic)

Figure 29 Start Up ENABLE Vs VOUT Trim Down 10% (VIN = 36V IOUT = 18A COUT = 12X10µF X7R Ceramic)

Figure 30 Start Up ENABLE Vs VOUT Trim Up 10% (VIN = 36V IOUT = 18A COUT = 12X10µF X7R Ceramic)
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 13 of 18
Page 14
Typical Performance Characteristics:

Figure 31 Start Up ENABLE Vs VOUT (VIN = 36V IOUT = 18A Resistive COUT = 4mF CSS = 0.1µF)

Figure 32 Start Up ENABLE Vs VOUT (VIN = 75V IOUT = 18A Resistive COUT = 4mF CSS = 0.1µF)

Figure 33 Start Up ENABLE Vs IOUT Short Circuit (VIN = 48V Shorting Bar Across +OUT To -OUT)

Figure 34 Forced Over Temperature
(VIN = 75V TCASE = 135°C IOUT = 27A)
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 14 of 18
Page 15
Package Outline & Recommended PCB Land Pattern

Figure 35
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 15 of 18
Page 16
Ordering Information And Available Options:
Available Options – Heat Sinks:
At present, Picor offers four different heat sink options to accommodate the customers space and cooling needs. Heat sinks are available in two sizes, one with 6.3mm fins and the other with 11mm fins. Each of those heat sinks can be ordered with a specific air flow direction in mind, both X-Flow and longitudinal are supported.

| Part Number | Package |
|---|---|
| PI3101-00-HVIZ | 0.87”(w) x 0.65”(l) x 0.265”(h) |
| 32784 | Transverse Fins Heatsink 11 mm * |
| 32786 | Transverse Fins Heatsink 6.3mm * |
| 32783 | Longitudinal Fins Heatsink 11 mm * |
| 32785 | Longitudinal Fins Heatsink 6.3 mm * |
\* Assorted spring loaded push pins (not provided) are available to accommodate various PCB thicknesses. Please visit www.vicorpower.com for ordering information and details.
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 16 of 18
Page 17
Ordering Information And Available Options:
Available Options – PI3101-EVAL1 Evaluation Board:
If you wish to evaluate the electrical and thermal performance of the PI3101, Picor can make available the PI3101-EVAL1 Evaluation Board. It comes with a fully populated high density isolated DC-DC power supply and a comprehensive user manual. For details contact Picor Applications Engineering or visit our website at www.picorpower.com.
Figure 37 Picor PI3101-EVAL1 Evaluation Board (Actual Size)
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 17 of 18
Page 18
Warranty
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor shall not be liable for collateral or consequential damage. This warranty is extended to the original purchaser only.
EXCEPT FOR THE FOREGOING EXPRESS WARRANTY, VICOR MAKES NO WARRANTY, EXPRESS OR LIMITED, INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Vicor will repair or replace defective products in accordance with its own best judgment. For service under this warranty, the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping instructions. Products returned without prior authorization will be returned to the buyer. The buyer will pay all charges incurred in returning the product to the factory. Vicor will pay all reshipment charges if the product was defective within the terms of this warranty.
Information published by Vicor has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Vicor reserves the right to make changes to any products without further notice to improve reliability, function, or design. Vicor does not assume any liability arising out of the application or use of any product or circuit; neither does it convey any license under its patent rights nor the rights of others. Vicor general policy does not recommend the use of its components in life support applications wherein a failure or malfunction may directly threaten life or injury. Per Vicor Terms and Conditions of Sale, the user of
Vicor components in life support applications assumes all risks of such use and indemnifies Vicor against all damages.
Vicor’s comprehensive line of power solutions includes high density AC-DC and DC-DC
modules and accessory components, fully configurable AC-DC and DC-DC power
supplies, and complete custom power systems.
Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor components are not designed to be used in applications, such as life support systems, wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor’s Terms and Conditions of Sale, which are available upon request.
Specifications are subject to change without notice.
Intellectual Property Notice
Vicor and its subsidiaries own Intellectual Property (including U.S. and Foreign Patents and pending patent applications) related to the products described in this data sheet. Interested parties should contact Vicor’s Intellectual Property Department.
The products described in this data sheet are protected by the following U.S. Patents Numbers: 6,788,033; 7,154,250; 7,561,446; 7,361,844; D496,906; D506,438; 6,940,013; 7,038,917; 6,969,909; 7,166,898; 6,421,262; 7,368,957; RE 40,072
Vicor Corporation 25 Frontage Road Andover, MA 01810 USA
Picor Corporation 51 Industrial Drive North Smithfield, RI 02896 USA
Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com
Tel: 800-735-6200 Fax: 978-475-6715
PI3101-00-HVIZ Rev 1.1, April 29th, 2010 Page 18 of 18