PGA103 TI
Document overview
- PDF pages: 10
Technical content
Page 1

SBOS031
Page 2
SPECIFICATIONS
ELECTRICAL
TA = +25°C, VS = ±15V, RL = 2kΩ unless otherwise specified.

Page 3
SPECIFICATIONS (CONT)
ELECTRICAL
TA = +25°C, VS = ±15V, RL = 2kΩ unless otherwise specified.

PIN CONFIGURATION

ORDERING INFORMATION
| MODEL | PACKAGE | TEMPERATURE RANGE |
| PGA103P PGA103U | 8-Pin Plastic DIP SO-8 Surface-Mount | –40°C to +85°C –40°C to +85°C |
ELECTROSTATIC
DISCHARGE SENSITIVITY
Any integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with ap-
propriate precautions. Failure to observe proper handling and
installation procedures can cause damage. ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet published speci-
fications.
ABSOLUTE MAXIMUM RATINGS

PACKAGE INFORMATION

NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix D of Burr-Brown IC Data Book.

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
Page 4
DICE INFORMATION
| PAD | FUNCTION |
| 1 2 3A, 3B, 3C(1) 4A, 4B, 4C(2) 6 7 8 | A0 A 1 Ground V IN V– V O V+ |

NC: No Connection NOTES: (1) Connect all three indicated pads. (2) Connect all three indicated pads. Substrate Bias: Internally connected to V– power supply.
MECHANICAL INFORMATION

TYPICAL PERFORMANCE CURVES
TA = +25°C, VS = ±15V unless otherwise noted.
VOLTAGE GAIN vs FREQUENCY

10k
100k
1M
10M
Frequency (Hz)
| MILS (0.001") | MILLIMETERS | |
| Die Size Die Thickness Min. Pad Size | 69 x 105 ±5 20 ±3 4 x 4 | 1.75 x 2.67 ±0.13 0.51 ±0.08 0.1 x 0.1 |
| Backing Gold | ||
POWER SUPPLY REJECTION vs FREQUENCY

10 100 1k 10k 100k 1M
Frequency (Hz)
Page 5
TYPICAL PERFORMANCE CURVES (CONT)
TA = +25°C, VS = ±15V unless otherwise noted.
INPUT VOLTAGE NOISE vs FREQUENCY 1000

1 10 100 1k 10k 100k 1M
Frequency (Hz)
QUIESCENT CURRENT vs TEMPERATURE

–50 –25 0 25 50 75 100 125
Temperature (°C)
INPUT CURRENT NOISE vs FREQUENCY

1 10 100 1k 10k 100k 1M
Frequency (Hz)
SMALL SIGNAL RESPONSE

LARGE SIGNAL RESPONSE

2µs/div
Page 6
APPLICATION INFORMATION
Figure 1 shows the basic connections required for operation of the PGA103. Applications with noisy or high impedance power supplies may require decoupling capacitors close to the device pins as shown.

FIGURE 1. Basic Connections.
The input and output are referred to the ground terminal, pin 3. This must be a low-impedance connection to assure good gain accuracy. A resistance of 0.1Ω in series with the ground pin will cause the gain in G=100 to decrease by approximately 0.2%.
DIGITAL INPUTS
The digital inputs, A0 and A1, select the gain according to the logic table in Figure 1. The digital inputs interface directly to common CMOS and TTL logic components. The logic inputs are referenced to the ground terminal, pin 3. The logic table in Figure 1 shows that logic “1” on both A0 and A1 is invalid. This logic code will not cause damage, but the amplifier output will not be predictable while this code is selected. The output will recover when a valid code is selected. The digital inputs are not latched, so a change in logic inputs immediately selects a new gain. Switching time of the logic is approximately 0.5µs. The time to respond to gain change
is equal to the switching time plus the time it takes the amplifier to settle to a new output voltage in the newly selected gain (see settling time specifications). Many applications use an external logic latch to access gain control signals from a high speed data bus. Using an external latch isolates the high speed digital bus from sensitive analog circuitry. Locate the latch circuitry as far as practical from analog circuitry to avoid coupling digital noise into the analog circuitry.
Some applications select gain of the PGA103 with switches or jumpers. Figure 2 shows pull-up resistors connected to assure a noise-free logic “1” when the switch or jumper is off or open. Fixed-gain applications can connect the logic inputs directly to V+ or ground (or other valid logic level) without a series resistor.

FIGURE 2. Switch or Jumper-Selected Gains.
OFFSET TRIMMING
Offset voltage is laser-trimmed to typically less than 200µV (referred to input) in all three gains. The input-referred offset voltage can be different for each gain.

FIGURE 3. Offset Voltage Trim Circuit.
Figure 3 shows a circuit used to trim the offset voltage of the PGA103. An op amp buffers the trim voltage to provide a low impedance at the ground terminal. This is required to maintain accurate gain. Remember that the logic inputs, A0 and A1, are referenced to this ground connection, so the logic threshold voltage will be affected by the trim voltage. This is insignificant if the offset adjustment is used only to trim offset voltage. If a large offset is used (greater than 0.1V), be sure that the logic input signals provide valid logic levels when referred to the voltage at the ground terminal, pin 3.
Page 7


FIGURE 5. Wide Input Voltage Range Amplifer.
FIGURE 4. Programmable Gain Instrumentation Amplifier.

| MODEL | CHARACTERISTICS |
| INA103 INA105 INA106 INA114 INA117 INA111 INA131 | Low Noise, 1nV/√Hz IA G = 1 Difference Amp G = 10 Difference Amp Resistor-Programmed Gain, Precision ±200V C-M Input Range Difference Amp FET Input, High Speed IA Precision, G = 100 IA |
FIGURE 6. Instrumentation Amplifier with Programmable Gain Output Amp.
Page 8
PACKAGE OPTION ADDENDUM
23-May-2025
www.ti.com
PACKAGING INFORMATION

(1) Status: For more details on status, see our product life cycle.
(2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind.
(3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition.
(4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width.
(5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board.
(6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part.
Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers
and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Page 9
PACKAGE MATERIALS INFORMATION
www.ti.com
23-May-2025
TUBE
T - Tube
height
L - Tube length


\*All dimensions are nominal
| Device | Package Name | Package Type | Pins | SPQ | L (mm) | W (mm) | T (µm) | B (mm) |
|---|---|---|---|---|---|---|---|---|
| PGA103U | D | SOIC | 8 | 75 | 506.6 | 8 | 3940 | 4.32 |
| PGA103U.A | D | SOIC | 8 | 75 | 506.6 | 8 | 3940 | 4.32 |
Pack Materials-Page 1
Page 10
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2025, Texas Instruments Incorporated