DATASHEET SEARCH SITE
Document overview
- PDF pages: 2
Technical content
Page 1
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CXseries
Chip Type, High Voltage / Long Life

High reliability, High voltage (to 50V).
CR
Low ESR, High ripple current.
Higher
Long life of 1500 to 3000 hours at 125°C.
Capacitance
SMD type : Lead free reflow soldering condition at
CX
260°C peak complete correspondence.
Adapted to the RoHS directive (2011/65/EU).
Higher Temperature CV
Specifications
| Item | Performance Characteristics |
| Category Temperature Range | –55 to +125°C |
| Rated Voltage Range | 16 to 50V |
| Rated Capacitance Range | 5.6 to 390µF |
| Capacitance Tolerance | ±20% at 120Hz, 20°C |
| Tangent of loss angle (tan δ) | Less than or equal to the specified value at 120Hz, 20°C |
| ESR ( 1) | Less than or equal to the specified value at 100kHz, 20°C |
| Leakage Current ( 2) | Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C |
| Temperature Characteristics (Max.Impedance Ratio) | Z+125°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25 |
| Endurance | Capacitance change Within ± 20% of initial capacitance value ( 3) The specifications listed at below shall be met when the tan δ 150% or less of the initial specified value capacitors are restored to 20°C after the rated voltage is applied for 3000 hours (φD = 6.3:1500hours) at 125°C. ESR ( 1) 150% or less of the initial specified value Leakage current ( 2) Less than or equal to the initial specified value |
| Damp Heat (Steady State) | Capacitance change Within ± 20% of initial capacitance value ( 3) The specifications listed at below shall be met when the tan δ 150% or less of the initial specified value capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. ESR ( 1) 150% or less of the initial specified value Leakage current ( 2) Less than or equal to the initial specified value |
| Resistance to Soldering Heat | After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. Capacitance change Within ± 10% of the initial capacitance value ( 3) The duration for over +230°C temperature at capacitor surface shall tan δ 130% or less than the initial specified value not exceed 60 seconds. ESR ( 1) 130% or less than the initial specified value In the case of peak temp, less than 250°C, reflow soldering shall be Leakage current ( 2) Less than or equal to the initial specified value two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. |
| Marking | Navy blue print on the case top |
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions

Aid electrode
Dimension table in next page.
Type numbering system (Example : 35V 39µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Standard
(mm) Vibration Resistance (mm)


Voltage
| V | 16 | 20 | 25 | 35 | 50 |
| ode | C | D | E | V | H |
CAT.8100C
Page 2
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CXseries
Standard Ratings
| Rated Voltage (V)(code) | Surge Voltage (V) | Rated Capacitance (µF) | Case Size φD × L (mm) | tan δ | Leakage Current (µA) | ESR (mΩ) 。 (at 100kHz 20C) | Rated Ripple(mArms) | Part Number | |
|---|---|---|---|---|---|---|---|---|---|
| 16 (1C) | 18.4 | 47 | 6.3 × 6 | 0.12 | 150 | 55 | 1000 | 390 | PCX1C470MCL1GS |
| 82 | 8 × 7 | 0.12 | 262 | 45 | 1300 | 530 | PCX1C820MCL1GS | ||
| 82 | 8 × 7.5 | 0.12 | 262 | 45 | 1300 | 530 | PCX1C820MCS1GS | ||
| 100 | 6.3 × 8 | 0.12 | 320 | 33 | 1500 | 460 | PCX1C101MCL1GS | ||
| 100 | 6.3 × 8 | 0.12 | 320 | 33 | 1500 | 460 | PCX1C101MCS1GS | ||
| 150 | 8 × 10 | 0.12 | 480 | 28 | 2000 | 780 | PCX1C151MCL6GS | ||
| 150 | 8 × 10.5 | 0.12 | 480 | 28 | 2000 | 780 | PCX1C151MCS1GS | ||
| 150 | 10 × 8 | 0.12 | 480 | 33 | 1900 | 830 | PCX1C151MCL1GS | ||
| 220 | 8 × 12 | 0.12 | 704 | 27 | 2300 | 870 | PCX1C221MCL1GS | ||
| 270 | 10 × 10 | 0.12 | 864 | 27 | 2300 | 830 | PCX1C271MCL1GS | ||
| 270 | 10 × 10.5 | 0.12 | 864 | 27 | 2300 | 830 | PCX1C271MCS1GS | ||
| 390 | 10 × 12.7 | 0.12 | 1248 | 26 | 2700 | 1040 | PCX1C391MCL1GS | ||
| 20 (1D) | 23.0 | 33 | 6.3 × 6 | 0.12 | 132 | 60 | 900 | 380 | PCX1D330MCL1GS |
| 56 | 8 × 7 | 0.12 | 224 | 50 | 1300 | 500 | PCX1D560MCL1GS | ||
| 56 | 8 × 7.5 | 0.12 | 224 | 50 | 1300 | 500 | PCX1D560MCS1GS | ||
| 68 | 6.3 × 8 | 0.12 | 272 | 34 | 1450 | 470 | PCX1D680MCL1GS | ||
| 68 | 6.3 × 8 | 0.12 | 272 | 34 | 1450 | 470 | PCX1D680MCS1GS | ||
| 120 | 8 × 10 | 0.12 | 480 | 29 | 1900 | 770 | PCX1D121MCL6GS | ||
| 120 | 8 × 10.5 | 0.12 | 480 | 29 | 1900 | 770 | PCX1D121MCS1GS | ||
| 120 | 10 × 8 | 0.12 | 480 | 35 | 1800 | 810 | PCX1D121MCL1GS | ||
| 150 | 8 × 12 | 0.12 | 600 | 28 | 2200 | 860 | PCX1D151MCL1GS | ||
| 180 | 10 × 10 | 0.12 | 720 | 28 | 2300 | 800 | PCX1D181MCL1GS | ||
| 180 | 10 × 10.5 | 0.12 | 720 | 28 | 2300 | 800 | PCX1D181MCS1GS | ||
| 270 | 10 × 12.7 | 0.12 | 1080 | 27 | 2700 | 1020 | PCX1D271MCL1GS | ||
| 25 (1E) | 28.7 | 22 | 6.3 × 6 | 0.12 | 110 | 65 | 900 | 360 | PCX1E220MCL1GS |
| 39 | 8 × 7 | 0.12 | 195 | 55 | 1200 | 480 | PCX1E390MCL1GS | ||
| 39 | 8 × 7.5 | 0.12 | 195 | 55 | 1200 | 480 | PCX1E390MCS1GS | ||
| 56 | 6.3 × 8 | 0.12 | 280 | 35 | 1400 | 450 | PCX1E560MCL1GS | ||
| 56 | 6.3 × 8 | 0.12 | 280 | 35 | 1400 | 450 | PCX1E560MCS1GS | ||
| 82 | 8 × 10 | 0.12 | 410 | 30 | 1900 | 760 | PCX1E820MCL6GS | ||
| 82 | 8 × 10.5 | 0.12 | 410 | 30 | 1900 | 760 | PCX1E820MCS1GS | ||
| 82 | 10 × 8 | 0.12 | 410 | 36 | 1800 | 800 | PCX1E820MCL1GS | ||
| 120 | 8 × 12 | 0.12 | 600 | 29 | 2200 | 850 | PCX1E121MCL6GS | ||
| 120 | 10 × 10 | 0.12 | 600 | 29 | 2200 | 790 | PCX1E121MCL1GS | ||
| 120 | 10 × 10.5 | 0.12 | 600 | 29 | 2200 | 790 | PCX1E121MCS1GS | ||
| 180 | 10 × 12.7 | 0.12 | 900 | 28 | 2600 | 1010 | PCX1E181MCL1GS | ||
| 35 (1V) | 40.2 | 10 | 6.3 × 6 | 0.12 | 70 | 85 | 800 | 310 | PCX1V100MCL1GS |
| 18 | 8 × 7 | 0.12 | 126 | 60 | 1100 | 450 | PCX1V180MCL1GS | ||
| 18 | 8 × 7.5 | 0.12 | 126 | 60 | 1100 | 450 | PCX1V180MCS1GS | ||
| 27 | 6.3 × 8 | 0.12 | 189 | 45 | 1300 | 450 | PCX1V270MCL1GS | ||
| 27 | 6.3 × 8 | 0.12 | 189 | 45 | 1300 | 450 | PCX1V270MCS1GS | ||
| 39 | 8 × 10 | 0.12 | 273 | 35 | 1800 | 700 | PCX1V390MCL6GS | ||
| 39 | 8 × 10.5 | 0.12 | 273 | 35 | 1800 | 700 | PCX1V390MCS1GS | ||
| 39 | 10 × 8 | 0.12 | 273 | 41 | 1700 | 750 | PCX1V390MCL1GS | ||
| 56 | 8 × 12 | 0.12 | 392 | 33 | 2000 | 780 | PCX1V560MCL1GS | ||
| 68 | 10 × 10 | 0.12 | 476 | 30 | 2200 | 740 | PCX1V680MCL1GS | ||
| 68 | 10 × 10.5 | 0.12 | 476 | 30 | 2200 | 740 | PCX1V680MCS1GS | ||
| 100 | 10 × 10.5 | 0.12 | 700 | 25 | 2400 | 800 | PCX1V101MCS1GS | ||
| 100 | 10 × 12.7 | 0.12 | 700 | 29 | 2600 | 990 | PCX1V101MCL1GS | ||
| 50 (1H) | 57.5 | 5.6 | 6.3 × 6 | 0.12 | 56 | 105 | 700 | 280 | PCX1H5R6MCL1GS |
| 10 | 8 × 7 | 0.12 | 100 | 75 | 1000 | 410 | PCX1H100MCL1GS | ||
| 10 | 8 × 7.5 | 0.12 | 100 | 75 | 1000 | 410 | PCX1H100MCS1GS | ||
| 12 | 6.3 × 8 | 0.12 | 120 | 65 | 1100 | 380 | PCX1H120MCL1GS | ||
| 12 | 6.3 × 8 | 0.12 | 120 | 65 | 1100 | 380 | PCX1H120MCS1GS | ||
| 22 | 8 × 10 | 0.12 | 220 | 37 | 1700 | 680 | PCX1H220MCL6GS | ||
| 22 | 8 × 10.5 | 0.12 | 220 | 37 | 1700 | 680 | PCX1H220MCS1GS | ||
| 22 | 10 × 8 | 0.12 | 220 | 56 | 1400 | 730 | PCX1H220MCL1GS | ||
| 27 | 8 × 12 | 0.12 | 270 | 35 | 2000 | 760 | PCX1H270MCL1GS | ||
| 33 | 10 × 10 | 0.12 | 330 | 31 | 2200 | 630 | PCX1H330MCL1GS | ||
| 33 | 10 × 10.5 | 0.12 | 330 | 31 | 2200 | 630 | PCX1H330MCS1GS | ||
| 47 | 10 × 12.7 | 0.12 | 470 | 30 | 2500 | 970 | PCX1H470MCL1GS | ||
| Ambient temperature of a capacitor Rated ripple current (mArms) at 105°C 100kHz | |||||||||
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
No marked, will be put at 12th digit of type numbering system.
Recommended land size, soldering by reflow are given in page 18, 19.
: In this case, will be put at 12th digit of type numbering system.
Please refer to page 3 for the minimum order quantity.