PCX NICHICON
Document overview
- PDF pages: 2
Technical content
Page 1
| CONDUCTIVE POLYMER ALUMINUM SOLID ELECT | ROLYTIC CAPACITORS |
|---|---|
| PCX Chip Type, High Voltage / Long Life High reliability, High voltage (to 50V). PCR Low ESR, High ripple current. Long life of 1500 to 3000 hours at 125°C. CapH aig ch ite ar nce SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. PCX Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. Higher Temperature | |
PCV
Specifications
| Item | Performance Characteristics |
| Category Temperature Range | –55 to +125°C |
| Rated Voltage Range | 16 to 50V |
| Rated Capacitance Range | 5.6 to 390µF |
| Capacitance Tolerance | ± 20% at 120Hz, 20°C |
| Tangent of loss angle (tan δ) | Less than or equal to the specified value at 120Hz, 20°C |
| ESR ( 1) | Less than or equal to the specified value at 100kHz, 20°C |
| Leakage Current ( 2) | Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C |
| Temperature Characteristics (Max.Impedance Ratio) | Z+125°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25 |
| Endurance | Capacitance change Within ± 20% of initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less of the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less of the initial specified value applied for 3000 hours (φD = 6.3:1500hours) at 125°C. Leakage current ( 2) Less than or equal to the initial specified value |
| Damp Heat (Steady State) | Capacitance change Within ± 20% of initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less of the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less of the initial specified value applied for 1000 hours at 60°C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value |
| Resistance to Soldering Heat | After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall Capacitance change Within ± 10% of the initial capacitance value ( 3) not exceed 60 seconds. tan δ 130% or less than the initial specified value In case peak temperature is 250°C or less, reflow soldering shall be ESR ( 1) 130% or less than the initial specified value two times maximum. Leakage current ( 2) Less than or equal to the initial specified value In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. |
| Marking | Navy blue print on the case top |
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
Type numbering system (Example : 35V 39µF)
3 Initial value : The value before test of examination of resistance to soldering.
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Dimensions

(mm) Vibration Resistance (mm)
Standard


Frequency coefficient of rated ripple current
V
Frequency 120Hz 1kHz 10kHz 100kHz or more
Code C D E V H
Coefficient 0.05 0.30 0.70 1.00
Aid electrode
φ10×12.7L : The vibration structure-resistant product is also available upon request, please ask for details.
Dimension table in next page.
CAT.8100H
Page 2
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
PCX
Dimensions
| Rated Voltage (V)(code) | Surge Voltage (V) | Rated Capacitance (µF) | Case Size φD × L (mm) | tan δ | Leakage Current (µA) | ESR (mΩ) (at 100kHz 20°C) | Rated Ripple(mArms) | Part Number | |
|---|---|---|---|---|---|---|---|---|---|
| 16 (1C) | 18.4 | 47 | 6.3 × 6 | 0.12 | 150 | 55 | 1000 | 390 | PCX1C470MCL1GS |
| 82 | 8 × 7 | 0.12 | 262 | 45 | 1300 | 530 | PCX1C820MCL1GS | ||
| 100 | 6.3 × 8 | 0.12 | 320 | 33 | 1500 | 460 | PCX1C101MCL1GS | ||
| 100 | 6.3 × 8 | 0.12 | 320 | 33 | 1500 | 460 | PCX1C101MCS1GS | ||
| 150 | 8 × 10 | 0.12 | 480 | 28 | 2000 | 780 | PCX1C151MCL6GS | ||
| 150 | 8 × 10.5 | 0.12 | 480 | 28 | 2000 | 780 | PCX1C151MCS1GS | ||
| 150 | 10 × 8 | 0.12 | 480 | 33 | 1900 | 830 | PCX1C151MCL1GS | ||
| 220 | 8 × 12 | 0.12 | 704 | 27 | 2300 | 870 | PCX1C221MCL1GS | ||
| 270 | 10 × 10 | 0.12 | 864 | 27 | 2300 | 830 | PCX1C271MCL1GS | ||
| 270 | 10 × 10.5 | 0.12 | 864 | 27 | 2300 | 830 | PCX1C271MCS1GS | ||
| 390 | 10 × 12.7 | 0.12 | 1248 | 26 | 2700 | 1040 | PCX1C391MCL1GS | ||
| 20 (1D) | 23.0 | 33 | 6.3 × 6 | 0.12 | 132 | 60 | 900 | 380 | PCX1D330MCL1GS |
| 56 | 8 × 7 | 0.12 | 224 | 50 | 1300 | 500 | PCX1D560MCL1GS | ||
| 68 | 6.3 × 8 | 0.12 | 272 | 34 | 1450 | 470 | PCX1D680MCL1GS | ||
| 68 | 6.3 × 8 | 0.12 | 272 | 34 | 1450 | 470 | PCX1D680MCS1GS | ||
| 120 | 8 × 10 | 0.12 | 480 | 29 | 1900 | 770 | PCX1D121MCL6GS | ||
| 120 | 8 × 10.5 | 0.12 | 480 | 29 | 1900 | 770 | PCX1D121MCS1GS | ||
| 120 | 10 × 8 | 0.12 | 480 | 35 | 1800 | 810 | PCX1D121MCL1GS | ||
| 150 | 8 × 12 | 0.12 | 600 | 28 | 2200 | 860 | PCX1D151MCL1GS | ||
| 180 | 10 × 10 | 0.12 | 720 | 28 | 2300 | 800 | PCX1D181MCL1GS | ||
| 180 | 10 × 10.5 | 0.12 | 720 | 28 | 2300 | 800 | PCX1D181MCS1GS | ||
| 270 | 10 × 12.7 | 0.12 | 1080 | 27 | 2700 | 1020 | PCX1D271MCL1GS | ||
| 25 (1E) | 28.7 | 22 | 6.3 × 6 | 0.12 | 110 | 65 | 900 | 360 | PCX1E220MCL1GS |
| 39 | 8 × 7 | 0.12 | 195 | 55 | 1200 | 480 | PCX1E390MCL1GS | ||
| 56 | 6.3 × 8 | 0.12 | 280 | 35 | 1400 | 450 | PCX1E560MCL1GS | ||
| 56 | 6.3 × 8 | 0.12 | 280 | 35 | 1400 | 450 | PCX1E560MCS1GS | ||
| 82 | 8 × 10 | 0.12 | 410 | 30 | 1900 | 760 | PCX1E820MCL6GS | ||
| 82 | 8 × 10.5 | 0.12 | 410 | 30 | 1900 | 760 | PCX1E820MCS1GS | ||
| 82 | 10 × 8 | 0.12 | 410 | 36 | 1800 | 800 | PCX1E820MCL1GS | ||
| 120 | 8 × 12 | 0.12 | 600 | 29 | 2200 | 850 | PCX1E121MCL6GS | ||
| 120 | 10 × 10 | 0.12 | 600 | 29 | 2200 | 790 | PCX1E121MCL1GS | ||
| 120 | 10 × 10.5 | 0.12 | 600 | 29 | 2200 | 790 | PCX1E121MCS1GS | ||
| 180 | 10 × 12.7 | 0.12 | 900 | 28 | 2600 | 1010 | PCX1E181MCL1GS | ||
| 35 (1V) | 40.2 | 10 | 6.3 × 6 | 0.12 | 70 | 85 | 800 | 310 | PCX1V100MCL1GS |
| 18 | 8 × 7 | 0.12 | 126 | 60 | 1100 | 450 | PCX1V180MCL1GS | ||
| 27 | 6.3 × 8 | 0.12 | 189 | 45 | 1300 | 450 | PCX1V270MCL1GS | ||
| 27 | 6.3 × 8 | 0.12 | 189 | 45 | 1300 | 450 | PCX1V270MCS1GS | ||
| 39 | 8 × 10 | 0.12 | 273 | 35 | 1800 | 700 | PCX1V390MCL6GS | ||
| 39 | 8 × 10.5 | 0.12 | 273 | 35 | 1800 | 700 | PCX1V390MCS1GS | ||
| 39 | 10 × 8 | 0.12 | 273 | 41 | 1700 | 750 | PCX1V390MCL1GS | ||
| 56 | 8 × 12 | 0.12 | 392 | 33 | 2000 | 780 | PCX1V560MCL1GS | ||
| 68 | 10 × 10 | 0.12 | 476 | 30 | 2200 | 740 | PCX1V680MCL1GS | ||
| 68 | 10 × 10.5 | 0.12 | 476 | 30 | 2200 | 740 | PCX1V680MCS1GS | ||
| 100 | 10 × 10.5 | 0.12 | 700 | 25 | 2400 | 800 | PCX1V101MCS1GS | ||
| 100 | 10 × 12.7 | 0.12 | 700 | 29 | 2600 | 990 | PCX1V101MCL1GS | ||
| 50 (1H) | 57.5 | 5.6 | 6.3 × 6 | 0.12 | 56 | 105 | 700 | 280 | PCX1H5R6MCL1GS |
| 10 | 8 × 7 | 0.12 | 100 | 75 | 1000 | 410 | PCX1H100MCL1GS | ||
| 12 | 6.3 × 8 | 0.12 | 120 | 65 | 1100 | 380 | PCX1H120MCL1GS | ||
| 12 | 6.3 × 8 | 0.12 | 120 | 65 | 1100 | 380 | PCX1H120MCS1GS | ||
| 22 | 8 × 10 | 0.12 | 220 | 37 | 1700 | 680 | PCX1H220MCL6GS | ||
| 22 | 8 × 10.5 | 0.12 | 220 | 37 | 1700 | 680 | PCX1H220MCS1GS | ||
| 22 | 10 × 8 | 0.12 | 220 | 56 | 1400 | 730 | PCX1H220MCL1GS | ||
| 27 | 8 × 12 | 0.12 | 270 | 35 | 2000 | 760 | PCX1H270MCL1GS | ||
| 33 | 10 × 10 | 0.12 | 330 | 31 | 2200 | 630 | PCX1H330MCL1GS | ||
| 33 | 10 × 10.5 | 0.12 | 330 | 31 | 2200 | 630 | PCX1H330MCS1GS | ||
| 47 | 10 × 12.7 | 0.12 | 470 | 30 | 2500 | 970 | PCX1H470MCL1GS | ||
| Ambient temperature of a capacitor | |||||||||
Rated ripple current (mArms) at 105°C 100kHz
No marked, 1 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system.
Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.