PCV NICHICON

Document overview

  • PDF pages: 3

Technical content

Page 1

CONDUCTIVE POLYMER ALUMINUM SOLID ELECT ROLYTIC CAPACITORS
PCV Chip Type, High Voltage / Long Life High voltage (to 125V), Low ESR, High ripple current. Load life of 3000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. PCX High Temperature PCV

Specifications

Item Performance Characteristics
Category Temperature Range –55 to +105°C
Rated Voltage Range 16 to 125V
Rated Capacitance Range 5.6 to 680µF
Capacitance Tolerance ± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25
Endurance Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 3000 hours at 105°C. Leakage current ( 2) Less than or equal to the initial specified value
Damp Heat (Steady State) Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 1000 hours at 60°C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value
Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at Capacitance change Within ± 10% of the initial capacitance value ( 3) right. tan δ 130% or less than the initial specified value Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. ESR ( 1) 130% or less than the initial specified value The duration for over +230°C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value not exceed 60 seconds. In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal.
Marking Navy blue print on the case top

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

PDF page 1 diagram

(mm)

Voltage

Size φ6.3 ×6L φ8 ×7L φ8 ×10L φ8 ×12L φ10 ×8L φ10 ×10
φD 6.3 8.0 8.0 8.0 10.0 10.0
L 5.9 6.9 9.9 11.9 7.9 9.9
A 7.3 9.0 9.0 9.0 11.0 11.0
B 6.6 8.3 8.3 8.3 10.3 10.3
C 6.6 8.3 8.3 8.3 10.3 10.3
E 2.1 3.2 3.2 3.2 4.6 4.6
H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.

φ10×12.7L 10.0 V 16 20 25 35

12.6 Code C D E V

11.0 10.3

Type numbering system (Example : 35V 82µF)

1 2 3 4 5 6 7 8 9 10 11 12 13 14

PDF page 1 diagram

50 63 80 100 125

H J K 2A 2B

Frequency coefficient of rated ripple current

10.3 0 Frequency0/ 120Hz 1kHz­

10kHz 100kHz or more

4.6 0.8 to 1.1 Coefficient 0.05 0.30

0.70 1.00

Dimension table in next page.

Page 2

Dimensions

Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) Part Number
16 (1C) 18.4 56 6.3 × 6 0.12 179 50 1000 PCV1C560MCL1GS
82 6.3 × 6 0.12 262 47 1300 PCV1C820MCL2GS
100 8 × 7 0.12 320 36 1500 PCV1C101MCL1GS
150 8 × 7 0.12 480 34 1700 PCV1C151MCL2GS
220 8 × 10 0.12 704 27 2000 PCV1C221MCL6GS
220 10 × 8 0.12 704 31 2000 PCV1C221MCL1GS
270 8 × 10 0.12 864 21 3800 PCV1C271MCL7GS
270 8 × 12 0.12 864 26 2300 PCV1C271MCL1GS
270 10 × 8 0.12 864 24 3200 PCV1C271MCL2GS
330 10 × 10 0.12 1056 26 2400 PCV1C331MCL1GS
390 8 × 12 0.12 1248 20 4100 PCV1C391MCL2GS
470 10 × 10 0.12 1504 21 3900 PCV1C471MCL2GS
470 10 × 12.7 0.12 1504 25 2800 PCV1C471MCL1GS
680 10 × 12.7 0.12 2176 19 4400 PCV1C681MCL2GS
20 (1D) 23.0 47 6.3 × 6 0.12 188 55 1000 PCV1D470MCL1GS
56 6.3 × 6 0.12 224 48 1300 PCV1D560MCL2GS
68 8 × 7 0.12 272 45 1300 PCV1D680MCL1GS
100 8 × 7 0.12 400 42 1400 PCV1D101MCL2GS
150 8 × 10 0.12 600 28 2000 PCV1D151MCL6GS
150 10 × 8 0.12 600 33 1900 PCV1D151MCL1GS
180 10 × 8 0.12 720 25 3100 PCV1D181MCL2GS
220 8 × 10 0.12 880 22 3700 PCV1D221MCL7GS
220 8 × 12 0.12 880 27 2300 PCV1D221MCL1GS
270 8 × 12 0.12 1080 21 4000 PCV1D271MCL2GS
270 10 × 10 0.12 1080 27 2300 PCV1D271MCL1GS
330 10 × 10 0.12 1320 22 3800 PCV1D331MCL2GS
330 10 × 12.7 0.12 1320 26 2700 PCV1D331MCL1GS
470 10 × 12.7 0.12 1880 20 4300 PCV1D471MCL2GS
25 (1E) 28.7 33 6.3 × 6 0.12 165 60 1000 PCV1E330MCL1GS
47 6.3 × 6 0.12 235 49 1300 PCV1E470MCL2GS
56 8 × 7 0.12 280 50 1300 PCV1E560MCL1GS
82 8 × 7 0.12 410 47 1400 PCV1E820MCL2GS
120 8 × 10 0.12 600 29 1900 PCV1E121MCL6GS
120 10 × 8 0.12 600 35 1800 PCV1E121MCL1GS
150 8 × 10 0.12 750 23 3600 PCV1E151MCL7GS
150 8 × 12 0.12 750 28 2200 PCV1E151MCL1GS
150 10 × 8 0.12 750 26 3000 PCV1E151MCL2GS
180 10 × 10 0.12 900 28 2300 PCV1E181MCL1GS
220 8 × 12 0.12 1100 22 3800 PCV1E221MCL2GS
270 10 × 10 0.12 1350 23 3700 PCV1E271MCL2GS
270 10 × 12.7 0.12 1350 27 2700 PCV1E271MCL1GS
390 10 × 12.7 0.12 1950 21 4200 PCV1E391MCL2GS
35 (1V) 40.2 18 6.3 × 6 0.12 126 64 900 PCV1V180MCL1GS
22 6.3 × 6 0.12 154 50 1300 PCV1V220MCL2GS
27 8 × 7 0.12 189 55 1200 PCV1V270MCL1GS
39 8 × 7 0.12 273 52 1400 PCV1V390MCL2GS
56 8 × 10 0.12 392 31 1900 PCV1V560MCL1GS
68 10 × 8 0.12 476 37 1800 PCV1V680MCL1GS
82 8 × 10 0.12 574 24 3600 PCV1V820MCL7GS
82 8 × 12 0.12 574 29 2200 PCV1V820MCL1GS
82 10 × 8 0.12 574 27 3000 PCV1V820MCL2GS
100 10 × 10 0.12 700 29 2200 PCV1V101MCL1GS
120 8 × 12 0.12 840 23 3800 PCV1V121MCL7GS
120 10 × 10 0.12 840 24 3700 PCV1V121MCL2GS
150 10 × 12.7 0.12 1050 28 2600 PCV1V151MCL1GS
180 10 × 12.7 0.12 1260 22 4100 PCV1V181MCL2GS

Page 3

Dimensions

Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) Part Number
50 (1H) 57.5 8.2 6.3 ×6 0.12 82 81 800 PCV1H8R2MCL1GS
12 6.3 × 6 0.12 120 55 1200 PCV1H120MCL2GS
15 8 × 7 0.12 150 63 1100 PCV1H150MCL1GS
22 8 × 7 0.12 220 60 1300 PCV1H220MCL2GS
33 8 × 10 0.12 330 36 1700 PCV1H330MCL6GS
33 10 × 8 0.12 330 49 1500 PCV1H330MCL1GS
39 8 × 12 0.12 390 34 2000 PCV1H390MCL1GS
47 8 × 10 0.12 470 29 3300 PCV1H470MCL7GS
47 10 × 8 0.12 470 37 2600 PCV1H470MCL2GS
47 10 × 10 0.12 470 30 2200 PCV1H470MCL1GS
56 8 × 12 0.12 560 28 3400 PCV1H560MCL2GS
68 10 × 10 0.12 680 29 3400 PCV1H680MCL2GS
68 10 × 12.7 0.12 680 29 2600 PCV1H680MCL1GS
100 10 × 12.7 0.12 1000 27 3600 PCV1H101MCL2GS
63 (1J) 72.4 5.6 6.3 × 6 0.12 71 105 700 PCV1J5R6MCL1GS
8.2 6.3 × 6 0.12 103 56 1200 PCV1J8R2MCL2GS
10 8 × 7 0.12 126 75 1000 PCV1J100MCL1GS
12 8 × 7 0.12 151 70 1100 PCV1J120MCL2GS
22 8 × 10 0.12 277 37 1700 PCV1J220MCL6GS
22 10 × 8 0.12 277 56 1400 PCV1J220MCL1GS
27 8 × 10 0.12 340 30 3200 PCV1J270MCL7GS
27 8 × 12 0.12 340 35 2000 PCV1J270MCL1GS
27 10 × 8 0.12 340 38 2500 PCV1J270MCL2GS
33 10 × 10 0.12 416 31 2200 PCV1J330MCL1GS
39 8 × 12 0.12 491 29 3400 PCV1J390MCL2GS
47 10 × 10 0.12 592 30 3300 PCV1J470MCL2GS
47 10 × 12.7 0.12 592 30 2500 PCV1J470MCL1GS
56 10 × 12.7 0.12 706 28 3400 PCV1J560MCL2GS
80 (1K) 92.0 10 8 × 10 0.12 160 43 1600 PCV1K100MCL1GS
12 8 × 12 0.12 192 41 1800 PCV1K120MCL1GS
15 10 × 10 0.12 240 39 1900 PCV1K150MCL1GS
22 10 × 12.7 0.12 352 38 2200 PCV1K220MCL1GS
100 (2A) 115 6.8 8 × 10 0.12 136 48 1500 PCV2A6R8MCL1GS
10 8 × 12 0.12 200 45 1700 PCV2A100MCL1GS
12 10 × 10 0.12 240 42 1900 PCV2A120MCL1GS
18 10 × 12.7 0.12 360 41 2100 PCV2A180MCL1GS
125 (2B) 143 6.8 8 × 10 0.12 170 93 1100 PCV2B6R8MCL1GS
8.2 8 × 12 0.12 205 84 1300 PCV2B8R2MCL1GS
12 10 × 10 0.12 300 69 1400 PCV2B120MCL1GS
15 10 × 12.7 0.12 375 48 2000 PCV2B150MCL1GS

Rated ripple current (mArms) at 105°C 100kHz

No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. : In this case, 7 will be put at 12th digit of type numbering system.

Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.