PCS NICHICON

Document overview

  • PDF pages: 2

Technical content

Page 1

PDF page 1 diagram
CONDUCTIVE POLYMER ALUMINUM SOLID ELEC TROLYTIC CAPACITORS
PCS Chip Type, LongLife Assurance Load life of 5000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. PCS Long Life PCF

Specifications

PDF page 1 diagram
Item Performance Characteristics
Category Temperature Range –55 to +105°C
Rated Voltage Range 4 to 16V
Rated Capacitance Range 22 to 560µF
Capacitance Tolerance ± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25
Endurance Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 5000 hours at 105°C. Leakage current ( 2) Less than or equal to the initial specified value
Damp Heat (Steady State) Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 1000 hours at 60°C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value
Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at Capacitance change Within ± 10% of the initial capacitance value ( 3) right. tan δ 130% or less than the initial specified value Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. ESR ( 1) 130% or less than the initial specified value The duration for over +230°C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value not exceed 60 seconds. In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal.
Marking Navy blue print on the case top

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

PDF page 1 diagram

(mm)

Size φ5 × 6L φ6.3 × 6L φ8 × 7L
φD 5.0 6.3 8.0
L 5.9 5.9 6.9
A 6.0 7.3 9.0
B 5.3 6.6 8.3
C 5.3 6.6 8.3
E 1.6 2.1 3.2
H 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1

Voltage

V 6.3

Code g j A C

Dimension table in next page.

Type numbering system (Example : 6.3V 220µF)

1 2 3 4 5 6 7 8 9 10 11 12 13 14

PDF page 1 diagram

Frequency coefficient of rated ripple current

0 Frequency0/ 120Hz 1kHz­ 10kHz 100kHz or more Coefficient 0.05 0.30 0.70

1.00

CAT.8100H

Page 2

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

PCS

Dimensions

Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) Part Number
4 (0G) 4.6 150 5 × 6 0.12 120 25 2200 PCS0G151MCL1GS
330 6.3 × 6 0.12 264 20 2800 PCS0G331MCL1GS
330 8 × 7 0.12 264 22 3200 PCS0G331MCL9GS
560 8 × 7 0.12 448 18 3600 PCS0G561MCL1GS
6.3 (0J) 7.2 47 5 × 6 0.12 100 35 1600 PCS0J470MCL1GS
100 5 × 6 0.12 126 25 2400 PCS0J101MCL1GS
100 6.3 × 6 0.12 126 22 2800 PCS0J101MCL9GS
120 6.3 × 6 0.12 151 22 2800 PCS0J121MCL9GS
220 6.3 × 6 0.12 277 20 2800 PCS0J221MCL1GS
220 8 × 7 0.12 277 22 3200 PCS0J221MCL9GS
390 8 × 7 0.12 491 22 3200 PCS0J391MCL1GS
10 (1A) 11.5 33 5 × 6 0.12 100 40 1300 PCS1A330MCL1GS
56 6.3 × 6 0.12 112 27 2300 PCS1A560MCL9GS
68 5 × 6 0.12 136 30 2100 PCS1A680MCL1GS
120 6.3 × 6 0.12 240 27 2300 PCS1A121MCL1GS
150 8 × 7 0.12 300 30 2600 PCS1A151MCL9GS
270 8 × 7 0.12 540 22 3200 PCS1A271MCL1GS
16 (1C) 18.4 22 5 × 6 0.12 100 45 1100 PCS1C220MCL1GS
39 5 × 6 0.12 125 35 2000 PCS1C390MCL1GS
39 6.3 × 6 0.12 125 30 2200 PCS1C390MCL9GS
68 6.3 × 6 0.12 218 30 2200 PCS1C680MCL1GS
82 8 × 7 0.12 262 28 2800 PCS1C820MCL9GS
120 8 × 7 0.12 384 28 2800 PCS1C121MCL1GS

Rated ripple current (mArms) at 105°C 100kHz

No marked, 1 will be put at 12th digit of type numbering system. : In this case, 9 will be put at 12th digit of type numbering system.

Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.

CAT.8100H