DATASHEET SEARCH SITE

Document overview

  • PDF pages: 3

Technical content

Page 1

CR series

Chip Type, High Reliability

High reliability, High voltage (to 100V).

Low ESR, High ripple current.

Long life of 4000 hours at 125°C.

SMD type : Lead free reflow soldering condition at

CR

260°C peak complete correspondence.

Adapted to the RoHS directive (2011/65/EU).

Added ESR specification after the test at -40°C.

Specifications

PDF page 1 diagram

High Capacitance

CX

Long Life Assurance

Item Performance Characteristics
Category Temperature Range –55 to +125°C
Rated Voltage Range 6.3 to 100V
Rated Capacitance Range 5.6 to 2700µF
Capacitance Tolerance ±20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(µA), whichever is greater.
Temperature Characteristics (Max.Impedance Ratio) Z+125°C / Z+20°C 1.25 (100kHz) Z–55°C / Z+20°C 1.25
Endurance The specifications listed at right shall be met when the Capacitance change Within ± 20% of initial capacitance value ( 3) capacitors are restored to 20°C after D.C. bias plus rated tan δ 150% or less of the initial specified value ripple current is applied for 4000 hours at 125°C, the peak ESR ( 1) 150% or less of the initial specified value voltage shall not exceed the rated voltage. Leakage current ( 2) Less than or equal to the initial specified value
Shelf Life The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C, 85% RH.
ESR after Endurance ( 1) Less than or equal to the specified value at 100kHz, -40°C
Damp Heat (Steady State) Capacitance change Within ± 20% of initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less of the initial specified value capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C, 85% RH. ESR ( 1) 150% or less of the initial specified value Leakage current ( 2) Less than or equal to the initial specified value
Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. Capacitance change Within ± 10% of the initial capacitance value ( 3) The duration for over +230°C temperature at capacitor surface shall tan δ 130% or less than the initial specified value not exceed 60 seconds. ESR ( 1) 130% or less than the initial specified value In the case of peak temp, less than 250°C, reflow soldering shall be Leakage current ( 2) Less than or equal to the initial specified value two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal.
Marking Navy blue print on the case top

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

PDF page 1 diagram

(mm)

Size φ5 × 6L φ6.3 × 6L φ6.3 × 8L φ8 × 7L φ8 × 10L φ8 × 12L φ10 × 8L φ10 × 10
φD 5.0 6.3 6.3 8.0 8.0 8.0 10.0 10.0
L 5.9 5.9 7.9 6.9 9.9 11.9 7.9 9.9
A 6.0 7.3 7.3 9.0 9.0 9.0 11.0 11.0
B 5.3 6.6 6.6 8.3 8.3 8.3 10.3 10.3
C 5.3 6.6 6.6 8.3 8.3 8.3 10.3 10.3
E 1.6 2.1 2.1 3.2 3.2 3.2 4.6 4.6
H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1

φ10×12.7L 10.0 12.6 11.0 10.3

Voltage

Type numbering system (Example : 35V 150µF)

1 2 3 4 5 6 7 8 9 10 11 12 13 14

PDF page 1 diagram

φ6.3 × 8L, φ8 × 7L, φ8 × 10L, φ10 × 10L : The vibration structure-resistant product is also available upon request, please ask for detail.

V 6.3 1 0 16 20 25 35 50 63 80 100
Code j A C D E V H J K 2A

10.3 4.6 0.8 to 1.1

Dimension table in next page.

Page 2

CRseries

Standard Ratings

Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Initial ESR (mΩ) 。 (20C / 100kHz) Low temp. ESR after Endurance (mΩ) 。 (-40C / 100kHz) Rated Ripple (mArms) 。 (125C / 100kHz) Part Number
6.3 (0J) 8 180 5 × 6 0.10 55 83 900 PCR0J181MCL1GS
330 6.3 × 6 0.10 32 48 1500 PCR0J331MCL1GS
560 6.3 × 8 0.10 20 30 1800 PCR0J561MCL4GS
560 8 × 7 0.10 25 38 1600 PCR0J561MCL1GS
1000 8 × 10 0.10 15 23 3700 PCR0J102MCL1GS
1200 10 × 8 0.10 18 27 3000 PCR0J122MCL1GS
1500 8 × 12 0.10 14 21 4000 PCR0J152MCL1GS
1800 10 × 10 0.10 15 23 3600 PCR0J182MCL1GS
2700 10 × 12.7 0.10 11 17 4700 PCR0J272MCL1GS
10 (1A) 13 120 5 × 6 0.10 60 90 800 PCR1A121MCL1GS
180 6.3 × 6 0.10 34 51 1400 PCR1A181MCL1GS
330 6.3 × 8 0.10 22 33 1700 PCR1A331MCL4GS
330 8 × 7 0.10 28 42 1600 PCR1A331MCL1GS
680 8 × 10 0.10 16 24 3500 PCR1A681MCL6GS
680 10 × 8 0.10 20 30 2900 PCR1A681MCL1GS
1000 8 × 12 0.10 15 23 3800 PCR1A102MCL1GS
1200 10 × 10 0.10 17 26 3400 PCR1A122MCL1GS
1500 10 × 12.7 0.10 12 18 4500 PCR1A152MCL1GS
16 (1C) 20 68 5 × 6 0.08 65 98 800 PCR1C680MCL1GS
120 6.3 × 6 0.08 36 54 1300 PCR1C121MCL1GS
220 6.3 × 8 0.08 23 35 1700 PCR1C221MCL4GS
220 8 × 7 0.08 30 45 1500 PCR1C221MCL1GS
470 8 × 10 0.08 17 26 3400 PCR1C471MCL6GS
470 10 × 8 0.08 22 33 2700 PCR1C471MCL1GS
560 8 × 12 0.08 16 24 3800 PCR1C561MCL1GS
680 10 × 10 0.08 19 29 3200 PCR1C681MCL1GS
1000 10 × 12.7 0.08 13 20 4300 PCR1C102MCL1GS
20 (1D) 25 56 5 × 6 0.08 70 105 700 PCR1D560MCL1GS
100 6.3 × 6 0.08 41 62 1300 PCR1D101MCL1GS
150 6.3 × 8 0.08 25 38 1700 PCR1D151MCL4GS
150 8 × 7 0.08 39 59 1200 PCR1D151MCL1GS
330 8 × 10 0.08 19 29 3300 PCR1D331MCL6GS
330 10 × 8 0.08 23 35 2600 PCR1D331MCL1GS
470 8 × 12 0.08 18 27 3500 PCR1D471MCL1GS
560 10 × 10 0.08 20 30 3100 PCR1D561MCL1GS
680 10 × 12.7 0.08 14 21 4200 PCR1D681MCL1GS
25 (1E) 31 33 5 × 6 0.08 75 113 700 PCR1E330MCL1GS
56 6.3 × 6 0.08 43 65 1300 PCR1E560MCL1GS
100 6.3 × 8 0.08 27 41 1600 PCR1E101MCL4GS
100 8 × 7 0.08 41 62 1200 PCR1E101MCL1GS
220 8 × 10 0.08 20 30 3200 PCR1E221MCL6GS
220 10 × 8 0.08 24 36 2500 PCR1E221MCL1GS
270 8 × 12 0.08 19 29 3300 PCR1E271MCL1GS
330 10 × 10 0.08 20 30 3100 PCR1E331MCL1GS
470 10 × 12.7 0.08 15 23 4100 PCR1E471MCL1GS
35 (1V) 43 27 5 × 6 0.08 80 120 600 PCR1V270MCL1GS
47 6.3 × 6 0.08 48 72 1100 PCR1V470MCL1GS
68 6.3 × 8 0.08 31 47 1500 PCR1V680MCL4GS
68 8 × 7 0.08 44 66 1200 PCR1V680MCL1GS
150 8 × 10 0.08 22 33 3100 PCR1V151MCL6GS
150 10 × 8 0.08 25 38 2500 PCR1V151MCL1GS
220 8 × 12 0.08 21 32 3300 PCR1V221MCL1GS
270 10 × 10 0.08 20 30 3100 PCR1V271MCL1GS
330 10 × 12.7 0.08 16 24 3900 PCR1V331MCL1GS

Page 3

CRseries

Standard Ratings

Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Initial ESR (mΩ) 。 (20C / 100kHz) Low temp. ESR after Endurance (mΩ) 。 (-40C / 100kHz) Rated Ripple (mArms) Part Number
50 (1H) 63 12 5 × 6 0.08 88 132 600 PCR1H120MCL1GS
22 6.3 × 6 0.08 50 75 1000 PCR1H220MCL1GS
39 6.3 × 8 0.08 36 54 1300 PCR1H390MCL4GS
39 8 × 7 0.08 45 68 1300 PCR1H390MCL1GS
82 8 × 10 0.08 26 39 2900 PCR1H820MCL6GS
82 10 × 8 0.08 34 51 2200 PCR1H820MCL1GS
120 8 × 12 0.08 25 38 2900 PCR1H121MCL2GS
120 10 × 10 0.08 25 38 3000 PCR1H121MCL1GS
180 10 × 12.7 0.08 19 29 3500 PCR1H181MCL1GS
63 (1J) 79 6.8 5 × 6 0.08 92 138 600 PCR1J6R8MCL1GS
12 6.3 × 6 0.08 51 77 1000 PCR1J120MCL1GS
22 6.3 × 8 0.08 45 68 1200 PCR1J220MCL4GS
22 8 × 7 0.08 48 72 1100 PCR1J220MCL1GS
39 8 × 10 0.08 28 42 2700 PCR1J390MCL1GS
47 10 × 8 0.08 35 53 2100 PCR1J470MCL1GS
56 8 × 12 0.08 27 41 2900 PCR1J560MCL1GS
68 10 × 10 0.08 28 42 2800 PCR1J680MCL1GS
100 10 × 12.7 0.08 24 36 3000 PCR1J101MCL1GS
80 (1K) 100 12 6.3 × 8 0.08 50 75 1200 PCR1K120MCL1GS
27 8 × 10 0.08 38 57 1400 PCR1K270MCL1GS
39 8 × 12 0.08 35 53 1600 PCR1K390MCL1GS
47 10 × 10 0.08 33 50 1700 PCR1K470MCL1GS
68 10 × 12.7 0.08 28 42 2100 PCR1K680MCL1GS
100 (2A) 125 5.6 6.3 × 8 0.08 55 83 1100 PCR2A5R6MCL1GS
12 8 × 10 0.08 45 68 1200 PCR2A120MCL1GS
18 8 × 12 0.08 42 63 1500 PCR2A180MCL1GS
22 10 × 10 0.08 39 59 1600 PCR2A220MCL1GS
33 10 × 12.7 0.08 28 42 2100 PCR2A330MCL1GS

Rated ripple current (mArms) at 125°C 100kHz

No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. : In this case, 4 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system.

Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.