PBB190 LITTELFUSE

Document overview

  • PDF pages: 7

Technical content

Page 1

Parameter Ratings Units
Blocking Voltage 400 V P
Load Current 130 mA / mA rms DC
On-Resistance (max) 25

Features

  • 5000Vrms Input/Output Isolation
  • Low Drive Power Requirements
  • Greater Reliability than Electromechanical Relays
  • No EMI/RFI Generation
  • Small 8-Pin Package
  • Surface Mount, Tape & Reel Version Available

Applications

  • Telecommunications
  • Telecom Switching
  • Tip/Ring Circuits
  • Modem Switching (Laptop, Notebook, Pocket Size)
  • Hook Switch
  • Dial Pulsing
  • Ground Start
  • Ringing Injection
  • Instrumentation
  • Multiplexers
  • Data Acquisition
  • Electronic Switching
  • I/O Subsystems
  • Meters (Watt-Hour, Water, Gas)
  • Medical Equipment-Patient/Equipment Isolation
  • Security
  • Industrial Controls

DS-PBB190-R05

400V, 130mA Dual Single-Pole

Normally Closed Relay

Description

PBB190 is a dual single-pole, normally closed (1-Form-B) solid state relay with two independently controlled switches that use optically coupled MOSFET technology to provide 5000Vrms of input to output isolation.

Its optically coupled outputs, which use the patented OptoMOS architecture, are controlled by a highly efficient infrared LED.

Dual single-pole OptoMOS relays provide a more compact design solution than discrete single-pole relays in a variety of applications by incorporating both relays in a single 8-pin package.

Approvals

  • UL Recognized Component: File E76270
  • TUV EN 62368-1: Certificate # B 082667 0008

Ordering Information

Part # Description
PBB190 8-Lead DIP (50/Tube)
PBB190S 8-Lead Surface Mount (50/Tube)
PBB190STR 8-Lead Surface Mount (1,000/Reel)

Pin Configuration

1

8

+ Control - Switch #1

Load - Switch #1

2

7

  • Control - Switch #1

Load - Switch #1

3

6

+ Control - Switch #2

Load - Switch #2 5

4

  • Control - Switch #2

Load - Switch #2

Switching Characteristics of Normally Closed Devices

PDF page 1 diagram

Page 2

Absolute Maximum Ratings @ 25ºC

Parameter Ratings Units
Blocking Voltage 400 V P
Reverse Input Voltage 5 V
LED Forward Current Peak (10ms) 50 mA
1 A
Input Power Dissipation 1 150 mW
Total Power Dissipation 2 800 mW
Isolation Voltage, Input to Output (60 Seconds) 5000 V rms
ESD Rating, Human Body Model 8 kV
Operational Temperature, Ambient -40 to +85 °C
Storage Temperature -40 to +125 °C

1 Derate linearly 1.33 mW / ºC 2 Derate output power linearly 6.67 mW / ºC

Electrical Characteristics @ 25ºC

Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied.

Typical values are characteristic of the device at +25°C, and are the result of engineering evaluations. They are provided for information purposes only, and are not part of the manufacturing testing requirements.

Parameter Conditions Symbol Min Typ Max Units
Output Characteristics
Blocking Voltage I=1A L V DRM 400 - - V P
Load Current 1 Continuous Peak I=0mA F I L - - 130 mA / mA rms DC
I=0mA, t=10ms F - - ±400 mA P
On-Resistance 2 I=0mA, I=130mA F L R ON - - 25
Off-State Leakage Current I=2mA, V=400V F L P I LEAK - - 1 A
Switching Speeds Turn-On Turn-Off I=5 mA, V=10V F L t on - - 1 ms
t off - - 2.5
Output Capacitance I=5mA, V=50V, f=1MHz F L C OUT - 11 - pF
Input Characteristics
LED Forward Current To Activate 3 To Deactivate I=130mA L I F - 0.38 2 mA
- 0.2 0.35 -
Input Voltage Drop I=5mA F V F 0.9 1.36 1.5 V
Reverse Input Current V=5V R I R - - 10 µA
Common Characteristics
Input to Output Capacitance V =0V, f=1MHz IO C IO - 3 - pF

1 If both poles operate simultaneously, then the load current must be derated so that the package power dissipation value is not exceeded. 2 Measurement taken within 1 second of on-time. 3 For high temperature operation (>60ºC), a minimum LED drive current of 4mA is recommended.

Page 3

PERFORMANCE DATA\*

Typical LED Forward Voltage Drop

Typical Turn-On Time

(N=50, IF=5mA)

(N=50, IF=5mA, IL=100mA)

PDF page 3 diagram
PDF page 3 diagram

Turn-On Time (ms)

LED Forward Voltage Drop (V)

Typical LED Forward Current

Typical On-Resistance Distribution

to Activate

(N=50, IF=0mA, IL=100mA)

(N=50, IL=100mA)

PDF page 3 diagram
PDF page 3 diagram

On-Resistance (:)

LED Forward Current (mA)

Typical Turn-On Time

Typical LED Forward Voltage Drop

vs. LED Forward Current

vs. Temperature

(IL=100mA)

PDF page 3 diagram
PDF page 3 diagram

LED Forward Current (mA)

Temperature (ºC)

Typical Turn-Off Time (N=50, IF=5mA, IL=100mA)

PDF page 3 diagram

Turn-Off Time (ms)

Typical Blocking Voltage Distribution (N=50, IF=2mA)

PDF page 3 diagram

Blocking Voltage (VP)

Typical Turn-Off Time vs. LED Forward Current (IL=100mA)

PDF page 3 diagram

LED Forward Current (mA)

Turn-Off Time vs. Temperature

Turn-On Time vs. Temperature (IL=75mA)

(IL=75mA)

PDF page 3 diagram
PDF page 3 diagram

Temperature (ºC)

Temperature (ºC)

\*Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC.

Page 4

PERFORMANCE DATA\*

LED Forward Current to Activate

On-Resistance

vs. Temperature

vs. Temperature

(IL=75mA)

(IF=0mA, IL=75mA)

PDF page 4 diagram
PDF page 4 diagram

Temperature (ºC)

Temperature (ºC)

Maximum Load Current

Typical Blocking Voltage

vs. Temperature

vs. Temperature

(IF=0mA)

(IF=5mA)

PDF page 4 diagram
PDF page 4 diagram

Temperature (ºC)

Temperature (ºC)

Output Capacitance vs. Load Voltage

Energy Rating Curve

(IF=5mA, f=1MHz)

Typical Load Current vs. Load Voltage (IF=0mA)

PDF page 4 diagram

Load Voltage (V)

Typical Leakage vs. Temperature Measured Across Pins 5&6, 7&8 (IF=5mA, VL=400V)

PDF page 4 diagram

Temperature (ºC)

PDF page 4 diagram
PDF page 4 diagram

Load Voltage (V)

Time

\*Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC.

Page 5

Manufacturing Information

Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits classifies its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below.

Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability.

This product carries a Moisture Sensitivity Level (MSL) classification as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.

Device Moisture Sensitivity Level (MSL) Classifi cation
PBB190S MSL 1

ESD Sensitivity

This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.

Soldering Profile Provided in the table below is the IPC/JEDEC J-STD-020 Classification Temperature (TC) and the maximum total dwell time (tP) in all reflow processes that the body temperature of these surface mount devices may be (TC - 5)°C or greater. The device’s body temperature must not exceed the Classification Temperature at any time during reflow soldering processes.

Device Classifi cation Temperature (T) c Dwell Time (t) P Max Refl ow Cycles
PBB190S 250ºC 30 seconds 3

For through-hole devices, the maximum pin temperature and maximum dwell time through all solder waves is provided in the table below. Dwell time is the interval beginning when the pins are initially immersed into the solder wave until they exit the solder wave. For multiple waves, the dwell time is from entering the first wave until exiting the last wave. During this time, pin temperatures must not exceed the maximum temperature given in the table below. Body temperature of the device must not exceed the limit shown in the table below at any time during the soldering process.

Device Maximum Pin Temperature Maximum Body Temperature Maximum Dwell Time Wave Cycles
PBB190 260ºC 250ºC 10 seconds* 1

\*Total cumulative duration of all waves.

Board Wash IXYS Integrated Circuits recommends the use of no-clean flux formulations. Board washing to reduce or remove flux residue following the solder reflow process is acceptable provided proper precautions are taken to prevent damage to the device. These precautions include but are not limited to: using a low pressure wash and providing a follow up bake cycle sufficient to remove any moisture trapped within the device due to the washing process. Due to the variability of the wash parameters used to clean the board, determination of the bake temperature and duration necessary to remove the moisture trapped within the package is the responsibility of the user (assembler). Cleaning or drying

methods that employ ultrasonic energy may damage the device and should not be used. Additionally, the device must not be exposed to halide flux or solvents.

Page 6

Mechanical Dimensions

PDF page 6 diagram

9.652 ± 0.381

7.620 ± 0.254

(0.380 ± 0.015)

(0.300 ± 0.010)

3.302 ± 0.051 (0.130 ± 0.002)

4.064 TYP

PDF page 6 diagram

Notes:

PCB Hole Pattern

8-0.762 DIA.

2.540 ± 0.127

(8-0.030 DIA.)

(0.100 ± 0.005)

9.144 ± 0.508 (0.360 ± 0.020)

7.620 ± 0.127

7.239 TYP.

(0.300 ± 0.005)

(0.285)

7.620 ± 0.127 (0.300 ± 0.005)

0.254 ± 0.0127 (0.010 ± 0.0005)

  1. Controlling dimension: Inches

Dimensions

  1. Leadframe thickness does not include solder plating (1000μinches max)

PBB190S

PDF page 6 diagram

3.302 ± 0.051 (0.130 ± 0.002)

7.620 ± 0.254 (0.300 ± 0.010)

PDF page 6 diagram

Notes:

mm (inches)

PCB Land Pattern

0.635 ± 0.127

2.54

(0.025 ± 0.005)

(0.10)

8.90

1.65

(0.3503)

(0.0649)

0.254 ± 0.0127 (0.010 ± 0.0005)

0.65 (0.0255)

  1. Controlling dimension: Inches 2. Coplanarity = 0.004” (0.102 mm) max

Dimensions

  1. Leadframe thickness does not include solder plating

mm (inches)

(1000μinches max)

Page 7

PBB190STR Tape & Reel

PDF page 7 diagram
PDF page 7 diagram

Dimensions mm

User Direction of Feed

(inches)

  1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 3. Controlling dimension: mm

For additional information please visit our website at: https://www.ixysic.com

Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at https://www.littelfuse.com/disclaimer-electronics.

Specification: DS-PBB190-R05 ©Copyright 2025, Littelfuse, Inc. OptoMOS® is a registered trademark of Littelfuse, Inc. All rights reserved. Printed in USA. 11/18/2025