MK3711

MK3711 RENESAS

Document overview

• Manufacturer or author: Provided By www.digicamel.com(free datasheet download site)
• PDF pages: 8

Technical content

Features

• MK3711D is a drop-in replacement for the earlier MK3711S device
• MK3711D offers an 8-16 MHz output frequency range and improved power supply noise rejection
• Uses an inexpensive 8 to 16 MHz external crystal
• On-chip VCXO with guaranteed pull range of ±115 ppm minim um
• VCXO tuning voltage 0 to 3.3 V
• Packaged in 8 pin SOIC (150 mil wide)
• Pb (lead) free package
• Industrial temperature range available MK3711B is Obsolete Block Diagram 8-16 MHz Voltage Controlled Crystal Oscillator VIN 8-16 MHz Pullable Crystal VDD GND

LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO VCXO AND MULTIPLIER IDT™ LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO 2 MK3711 REV K 051310 Pin Assignment Pin Descriptions VDD VIN DC GND REF DC X21 MK3711D

8 Pin (150 mil) SOIC

1 XI Input Crystal connection. Connect to the external pullable crystal. 2 VDD Power Connect to +3.3 V (0.01uf decoupling capacitor recommended). 3 VIN Input Voltage input to VCXO — 0 to 3.3 V analog input which controls the oscillation frequency of the VCXO. 4 GND Power Connect to ground. 5 DC — Do not connect anything to this pin.

6 REF Output VCXO CMOS level clock output matches the nominal frequency of the

crystal. 7 DC — Do not connect anything to this pin. 8 X2 Input Crystal connection. Connect to the external pullable crystal.

LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO VCXO AND MULTIPLIER IDT™ LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO 3 MK3711 REV K 051310 External Component Selection The MK3711 requires a minimum number of external components for proper operation. Decoupling Capacitor A decoupling capacitor of 0.01µF must be connected between VDD (pin 2) and GND (pin 4), as close to these pins as possible. For optimum device performance, the decoupling capacitor should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. Series Termination Resistor When the PCB trace between the clock output (CLK, pin 5) and the load is over 1 inch, series termination should be used. To series terminate a 50Ω trace (a commonly used trace impedance) place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. Quartz Crystal The MK3711 VCXO function consists of the external crystal and the integrated VCXO oscillator circuit. To assure the best system performance (frequency pull range) and reliability, a crystal device with the recommended parameters (shown below) must be used, and the layout guidelines discussed in the following section shown must be followed. The frequency of oscillation of a quartz crystal is determined by its “cut” and by the load capacitors connected to it. The MK3711 incorporates on-chip variable load capacitors that “pull” (change) the frequency of the crystal. The crystal specified for use with the MK3711 is designed to have zero frequency error when the total of on-chip + stray capacitance is 14 pF . Recommended Crystal Parameters: Initial Accuracy at 25 ° C ±20 ppm Temperature Stability ±30 ppm Aging ±20 ppm Load Capacitance 14 pf Shunt Capacitance, C0 7 pF Max C0/C1 Ratio 250 Max Equivalent Series Resistance 35 Ω Max For crystal frequencies between 13.5 MHz and 16 MHz, the nominal crystal load capacitance specification should be 14 pF . Contact IDT applications regarding the use of a crystal below 13.5 MHz. The external crystal must be connected as close to the chip as possible and should be on the same side of the PCB as the MK3711. There should be no vias between the crystal pins and the X1 and X2 device pins. There should be no signal traces underneath or close to the crystal. See application note MAN05. Crystal Tuning Load Capacitors The crystal traces should include pads for small fixed capacitors, one between X1 and ground, and another between X2 and ground. The need for these capacitors is determined at system prototype evaluation, and is influenced by the particular crystal used (manufacture and frequency) and by PCB layout. The typical required capacitor value is 1 to 4 pF . The procedure for determining the value of these capacitors can be found in application note MAN05.

LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO VCXO AND MULTIPLIER IDT™ LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO 4 MK3711 REV K 051310 Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK3711. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Recommended Operating Conditions Item Rating Supply Voltage, VDD 7 V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature (commercial) 0 to +70 ° C Ambient Operating Temperature (industrial) -40 to +85 ° C Storage Temperature -65 to +150 ° C Soldering Temperature 260 ° C Parameter Min. Typ. Max. Units Ambient Operating Temperature (commercial) 0 +70 ° C Ambient Operating Temperature (industrial) -40 +85 ° C Power Supply Voltage (measured in respect to GND) +3.15 +3.45 V Reference crystal parameters Refer to page 3

LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO VCXO AND MULTIPLIER IDT™ LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO 5 MK3711 REV K 051310 VDD=3.3 V ±5% , Ambient temperature -40 to +85° C, unless stated otherwise VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C, unless stated otherwise Note 1: External crystal device must conform with Pullable Crystal Specifications listed on page 3. Note 2: Original MK3711S and MK3711A provided ±100 ppm crystal pullability. Note 3: Original MK3711S and MK3711A provided 100 and 170 ppm/V respectively. Parameter Symbol Conditions Min. Typ. Max. Units Operating Voltage VDD 3.15 3.45 V Output High Voltage V OH IOH = -12 mA 2.4 V Output Low Voltage V OL IOL = 12 mA 0.4 V Output High Voltage (CMOS Level) VOH IOH = -4 mA VDD-0.4 V Operating Supply Current IDD Output = 12 MHz, no load 7m A Short Circuit Current I OS ±50 mA VIN, VCXO Control Voltage V IA 03 . 3 V Parameter Symbol Conditions Min. Typ. Max. Units Output Frequency F O 81 6 M H z Crystal Pullability, Note 2 F P 0V< VIN < 3.3 V, Note 1 ±115 ppm VCXO Gain MK3711D, Note 3 VIN = VDD/2 ± 1 V, Note 1 120 ppm/V Output Rise Time t OR 0.8 to 2.0 V, CL=15 pF 1.5 ns Output Fall Time t OF 2.0 to 0.8 V, CL=15 pF 1.5 ns Output Clock Duty Cycle t D Measured at 1.4 V, CL=15 pF 40 50 60 % Maximum Output Jitter, short term tJ CL=15 pF 100 ps

LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO VCXO AND MULTIPLIER IDT™ LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO 6 MK3711 REV K 051310 Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95

Ordering Information

"LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. Part / Order Number Marking Shipping Packaging Package Temperature MK3711DMLF 3711DMLF Tubes 8-pin SOIC 0 to +70 ° C MK3711DMLFTR 3711DMLF Tape and Reel 8-pin SOIC 0 to +70 ° C MK3711DMILF 3711DMIL Tubes 8-pin SOIC -40 to +85 ° C MK3711DMILFTR 3711DMIL Tape and Reel 8-pin SOIC -40 to +85 ° C INDEX AREA 1 2 D E SEATING PLANE A e - C - B .10 (.004) C C L H h x 45 *For reference only. Controlling dimensions in mm. Millimeters Inches Symbol Min Max Min Max A 1.35 1.75 .0532 .0688 A1 0.10 0.25 .0040 .0098 B 0 . 3 30 . 5 1. 0 1 3. 0 2 0 C 0.19 0.25 .0075 .0098 D 4.80 5.00 .1890 .1968 E 3.80 4.00 .1497 .1574 e 1.27 BASIC 0.050 BASIC H 5.80 6.20 .2284 .2440 h 0 . 2 50 . 5 0. 0 1 0. 0 2 0 L 0 . 4 01 . 2 7. 0 1 6. 0 5 0 α 0° 8° 0° 8°

© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names a nd marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA Corporate Headquarters Integrated Device Technology, Inc. www.idt.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 For Tech Support www.idt.com/go/clockhelp Innovate with IDT and accelerate your future networks. Contact: www.IDT.com MK3711 LOW COST 8 TO 16 MHZ 3.3 VOLT VCXO VCXO AND MULTIPLIER

© 202 Renesas Electronics Corporation. All rights reserved. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use o any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. ('LVFODLPHURev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, For further information on a product, technology, the most Koto-ku, Tokyo 135-0061, Japan up-to-date version of a document, or your nearest sales www.renesas.com office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners.