MAX-M10S_V01 ETC
Document overview
- Manufacturer or author: Provided By www.digicamel.com(free datasheet download site)
- PDF pages: 12
Technical content
pag. 1 Description 2 Move-X MAMWLE 2 u-blox MAX-M10S 3 Cloud-based positioning meets LoRaWAN 4 Specs 5 Pinout: General 6 Pinout: Analog/Digital (Arduino-like) 7 Pinout: SPI, UART, I2C 8 Pinout: Timers 9 Pinout: Others 10 Mechanical dimensions 11 External resources 11 Document revision 11
pag. 2
Description
The Move-X MAMWLE is a low-power, LoRaWAN-compliant radio module based on ST'sSTM32WLEx microcontroller by STMicroelectronics. Powered by a powerful 32-bit ARM Cortex-M4with clock frequency up to 48MHz and paired with up to 64kB SRAM and 256kB Flash, it issuitable for most IoT applications. More info and resources can be found here:https://www.move-x.it/mamwle-module/
pag. 3 u-blox MAX-M10S More info and resources are available here:https://www.u-blox.com/en/product/max-m10-series.
pag. 4 Cloud-based positioning meets LoRaWAN Cloud-basedpositioningworksbytransmittingGNSSsignalsthathavebeenpre-processedbytheGNSSreceivertothecloudserviceusingwirelesscommunication. Byreducingthetimethatthe GNSS receiver is switchedonandbyoutsourcingthepower-intensivepositioncalculationto the cloud, the overall power consumption of the positioning solution can be drasticallyreduced. More info and resources are available here:https://www.u-blox.com/en/product/max-m10-series.
pag. 5 Specs Radio module Move-X MAMWLE (STM32WLE5) CPU architecture STM32 Cortex® M4 32 bit @ 48MHz CPU flash memory 128 KB SRAM 48 KB LoRa radio Semtech SX1261/2 (868-915 MHz) GNSS module u-blox MAX-M10S BeiDou, Galileo, GLONASS, GPS / QZSS u-blox services: CloudLocate and AssistNow Board supply options (by priority) VIN (5V) USB (5V) Battery Supported batteries Rechargeable 3.70V Li-Ion or Li-Po with onboard SC OD OC protections, minimum suggested capacity 500mAh. Battery management specs 210 mA, charge voltage 4.2V, red LED for status Battery voltage monitor through MAMWLE ADC Operating voltage 3.3V LEDs Battery charge state (red), user application (green) Buttons Reset, user application Connectors Arduino MKR headers : up to 22 GPIO, 16 PWM, 7 analog in VREF output SPI, UART, I2C 10-pin JTAG/SWD for ST-LINK JST PH 2.0 for Li-Po battery u.fl for LoRa antenna u.fl for GNSS passive antenna Micro USB type B board supply and battery charging UART firmware upload USB-UART Bridge chip CP2102N Connected to MAMWLE USART2, BOOT0 and RESET Dimensions 62.9 x 25.0 x 7.52 mm
pag. 6 Pinout: General
pag. 7 Pinout: Analog/Digital (Arduino-like)
pag. 8 Pinout: SPI, UART, I2C
pag. 9 Pinout: Timers
pag. 10 Pinout: Others
pag. 11 Mechanical dimensions External resources Document revision Revision 1.0 - 14/9/2022