M7122 ETC2
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 1
Technical content
a 4 3 w7i22-1 [| | 1 This print end associated documents and the contained [of newisions Intormetion are the confidential property. of ELECTRONIC eee GABLE SeteRlfsTS* Shsireotsnd/or‘repreducton | INSTALLATION INSteUCTIONS — ee a St, cll or port theree! er manufacture ef hy part from 7 information contained on this. print not specivicaiy per- | 1, BEGIN BY CUTTING THE CABLE OFF SQUARE 2363] | a | See ECN Igy Boyt Hadl mitted by ELECTRONIC CABLE SPECIALISTS in writing is Ur | D a 8. SLIDE THE BODY OF THE CONNECTOR OVER THE ENO OF THE CABLE UNTIL THE D por ‘EERRULE NOTCH IN THE CONTACT SEATS WITH THE DIELECTRIC RIDGE INSIDE THE ‘contact CONNECTOR BODY. 1,500 + 2. WHEN USING AUTOMATIC STRIPPING EQUIPMENT, STRIP CABLE - “L200 | * 2S Sin'Sraeme mit Cr ono owe wins ne aT CARE NOT TO NICK THE CONDUCTORS WHILE STRIPPING THE NOT AVALABLE, STRIP ONLY L1 AND L3 AND TRIM EXCESS BRAID AT STEP 10. Fe P THE NECK OF THE CONNECTOR BODY. ecratnin 7 9. FOL BOTH BRADS UP OVER i241 3170 c 10, SUDE THE FERRULE UP OVER THE SHIELDS AND AGANST THE CONNECTOR c pensions /\\ BODY. TRIM AWAY ANY EXCESS BRAID. CRIMP THE FERRULE ONCE, NEXT 3. SUDE THE FERRULE AND ADHESIVE HEAT sunk A TO THE BODY, USING THE M22520/5~57 DIE (A HEX) IN A M22520/5-01 FICATION: OVER THE END OF TH ECABLE. TOOL FRAME. APPLY ADHESWE HEAT SHRINK. /)\\ ELECTRICAL IMPEDANCE: 50 OHMS NOMINAL << FREQUENCY RANGE: 0-8 GHz NOTE INSERTION LOSS" 09 a8 © 6 OH 4. SOLDER THE CONTACT ONTO THE CentER conoUcToR, pen «NOES DeLECIMG WanISTANONG, 2500 RMS @ SEA LEVEL MiL=STO-2000, USING 63Sn/37D SOLER OR CRIMP 1. ALL OMENSIONS ARE IN INCHES PSE Ot ASANDNG: 2500 VANS @ SE with M22520/5~57 OIE (@ HEX). ENSURE THE CONTACT 1S WORKING VOLTAGE: 1000 VEMS © SEA LEVEL BUTTED AGAINST THE CABLE DIELECTRIC. CLEAN ALL FLUX AA ENSURE HEAT SHRINK IS INSTALLED PRIOR TO CRIMPING CONNECTOR. S00 vouTs oe RESIOUES USING AN APPROPRIATE FLUX CLEANER A\\ ADHESNE HEAT SHRINK SHOULD BE APPLIED IN ACCORDANCE WITH wechawent ca ECS WORK INSTRUCTION W007. CONTACT ECS FOR A COPY OF THIS WORK B MECHANICAL INTERFACE PER ARINC SPEC 600 INSTRUCTION. B FIGURE 19~54.2 5. USING TWEEZERS, FOLD THE OUTER BRAID BACK OVER FEREN( INLY. TEIMATION sive: mee conact-sotoen on came | % USING TWEEZERS FOLD THE OUTER SRA aacx OVER {AN CONNECTOR OIMENSIONS ARE FOR REFERENCE ONL OUTER CONTACT-FERRULE CRIMP 5. DELETED. CABLE RETENTION: 30 LBS 6. DELETED. “ENVIRONMENTAL a 7. PICTORULS SHOW CONNECTOR INSTALLATION ON ECS 311901 CABLE. TEMPERATURE RATING: 651 70. +2007 WHEN INSTALLING TaIS CONNECTOR ON 3C1428 OR JCOSBA THERE ARE ONLY “S10: ONLY 2. BRAID SHIELDS WHICH SHOULD BE FOLDED BACK AS SHOWN IN STEP Fre UNS STO 202 METHOD 213. CON ono. @ EVERY 1/8". GENTLY ROTATE PIN TO SEPARATE THE FLAT FOIL CORROSION. wiL=StDu202, ueTHeD tor, Conde RAID AND ALUNINUM/POLYESTER FOIL FROM THE DIELECTRIC. " . } USING TWEEZERS, FOLO BACK ALUMINUM/POLYESTER FOIL WOISTURE RESISTANCE: ML~STD-202, METHOD 108 MOISTURE RESISTANCE OVER THE OUTER BRAD. ALL tenors winches| SERN eM B00: BRASS PER 00-8626 a FERRULE: ANNEALED BRASS PER 00-8-626 Cher TITLE: CUSTOMER SPECIFICATION A CENTER CONTACT: BERYLLIUM COPPER PER Q0-C-530 c CHAPMAN osoua ~WOOIRED SIZE 1, ARINC 600 AF CONNECTOR A DIELECTRIC: TEFLON PER L-P-403 7. USING TWEEZERS, FOLD THE INNER BRAD BACK OVER PEREHRPwan [9/18/98] FoR ECS CABLE 3c1428, $1190%, AND SCOSBA THE OUTER SMELD, LEAVING AS MUCH WEAVE As posseLe. PROP fcr ae EINISHES Provecr © FERRULE: BRIGHT NICKEL PER CQ-N-290 Toe er WTABennen [2/15/93] 166197 M7122 GOTER CONTACT, BOO GOLD FER wi~G~4800¢ 5 “oee /4/aqjeae [rte nmencomvenana[oas 1 or 3 | 4 3 2 1