LTC4050

DATASHEET SEARCH SITE

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

■ Wireless PDAs ■ Cellular Phones ■ Portable Electronics Standalone 750mA Li-Ion Battery Charger in 2 × 2 DFN ■ Complete Linear Charger in 2mm ××××× 2mm DFN Package ■ C/10 Charge Current Detection Output ■ Timer Termination ■ Charge Current Programmable up to 750mA with 5% Accuracy ■ No External MOSFET, Sense Resistor or Blocking Diode Required ■ Preset 4.2V Float Voltage with 0.6% Accuracy ■ Constant-Current/Constant-Voltage Operation with Thermal Feedback to Maximize Charging Rate Without Risk of Overheating ■ ACPR Pin Indicates Presence of Input Supply (LTC4065A Only) ■ Charge Current Monitor Output for Gas Gauging ■ Automatic Recharge ■ Charges Single Cell Li-Ion Batteries Directly from USB Port ■ 20µA Supply Current in Shutdown Mode ■ Soft-Start Limits Inrush Current ■ Tiny 6-Lead (2mm × 2mm) DFN Package FEATURES DESCRIPTIO U APPLICATIO SU TYPICAL APPLICATIO U VCC 510Ω R2* 500mA

4065 TA01

4.2V Li-Ion BATTERY V IN 4.3V TO 5.5V 1µF *SERIES 1Ω RESISTOR ONLY NEEDED FOR INDUCTIVE INPUT SUPPLIES LTC4065 CHRG EN BAT PROG GND The LTC 4065 is a complete constant-current/constant- voltage linear charger for single-cell lithium-ion batteries. Its 2mm × 2mm DFN package and low external component count make the LTC4065 especially well-suited for por- table applications. Furthermore, LTC4065 is specifically designed to work within USB power specifications. The CHRG pin indicates when charge current has dropped to ten percent of its programmed value (C/10). An internal timer terminates charging according to battery manufac- turer specifications. No external sense resistor or blocking diode is required due to the internal MOSFET architecture. Thermal feed- back regulates charge current to limit the die temperature during high power operation or high ambient temperature conditions. When the input supply (wall adapter or USB supply) is removed, the LTC4065 automatically enters a low current state, dropping battery drain current to less than 1µA. With power applied, LTC4065 can be put into shutdown mode, reducing the supply current to less than 20µA. The full-featured LTC4065 also includes automatic re- charge, low-battery charge conditioning (trickle charg- ing), soft-start (to limit inrush current) and an open-drain status pin to indicate the presence of an adequate input voltage (LTC4065A only). The LTC4065 is available in a tiny 6-lead, low profile (0.75mm) 2mm × 2mm DFN package. Standalone Li-Ion Battery Charger , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VCC VCC Supply Voltage (Note 4) ● 3.75 5.5 V ICC Quiescent VCC Supply Current V BAT = 4.5V (Forces IBAT and IPROG = 0) ● 120 250 µA ICCMS VCC Supply Current in Shutdown V EN = 5V (LTC4065) or Float PROG (LTC4065A) ● 20 40 µA ICCUV VCC Supply Current in Undervoltage V CC < VBAT, VCC = 3.5V, VBAT = 4V ● 61 1 µA Lockout VFLOAT VBAT Regulated Output Voltage I BAT = 2mA 4.175 4.2 4.225 V IBAT = 2mA, 0°C < TA < 85°C 4.158 4.2 4.242 V IBAT BAT Pin Current R PROG = 10k (0.1%), Current Mode ● 88 100 112 mA RPROG = 2k (0.1%), Current Mode ● 475 500 525 mA IBMS Battery Drain Current in Shutdown V EN = VCC (LTC4065), ● –1 0 1 µA Mode V PROG > VMS,PROG (LTC4065A) IBUV Battery Drain Current in Undervoltage V CC = 3.5V, VBAT = 4V ● 014 µA Lockout VUVLO VCC Undervoltage Lockout Voltage V CC Rising ● 3.4 3.6 3.8 V VCC Falling ● 2.8 3.0 3.2 V VPROG PROG Pin Voltage R PROG = 2k, IPROG = 500µA ● 0.98 1 1.02 V RPROG = 10k, IPROG = 100µA ● 0.98 1 1.02 V VASD Automatic Shutdown Threshold (V CC – VBAT), VCC Low to High 60 82 100 mV Voltage (V CC – VBAT), VCC High to Low 15 32 45 mV VMSH Manual Shutdown High Voltage V EN Rising 1 V (LTC4065) VMSL Manual Shutdown Low Voltage V EN Falling 0.6 V (LTC4065) REN EN Pin Input Resistance ● 0.95 1.5 3.3 M Ω VCC EN (LTC4065), ACPR (LTC4065A).. –0.3V to V CC + 0.3V Operating Temperature Range (Note 2) .. –40 °C to 85°C ABSOLUTE AXI U RATI GSW WW U PACKAGE/ORDER I FOR ATIOUU W (Note 1) The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. VCC = 5V, VBAT = 3.8V, VEN = 0V (LTC4065 only) unless otherwise specified. (Note 2)

ELECTRICAL CHARACTERISTICS

TJMAX = 125°C, θJA = 60°C/W (NOTE 3) EXPOSED PAD (PIN 7) IS GND, MUST BE SOLDERED TO PCB *EN PIN 5 ON LTC4065EDC, ACPR PIN 5 ON LTC4065AEDC ORDER PART NUMBER DC PART MARKING Consult LTC Marketing for parts specified with wider operating temperature ranges. LTC4065EDC LTC4065AEDC LBPG LBVJ Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ TOP VIEW DC PACKAGE 6-LEAD (2mm × 2mm) PLASTIC DFN 1GND CHRG BAT PROG EN/ACPR* V CC

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS IPROG PROG Pin Pull-Up Current V PROG > 1V 3 µA (LTC4065A) VMS,PROG PROG Shutdown Threshold Voltage V PROG Rising ● 3.7 4 4.3 V (LTC4065A Only) tSS Soft-Start Time 180 µs ITRKL Trickle Charge Current V BAT = 2V, RPROG = 2k (0.1%) 35 50 65 mA VTRKL Trickle Charge Threshold Voltage V BAT Rising ● 2.7 2.9 3.05 V VTRHYS Trickle Charge Hysteresis Voltage 90 mV ∆VRECHRG Recharge Battery Threshold Voltage V FLOAT – VRECHRG, 0°C < TA < 85°C 70 100 130 mV ∆VUVCL1 (VCC – VBAT) Undervoltage Current I BAT = 90% Programmed Charge Current 180 220 330 mV ∆VUVCL2 Limit I BAT = 10% Programmed Charge Current 90 125 150 mV tTIMER Termination Timer ● 3 4.5 6 Hrs Recharge Time ● 1.5 2.25 3 Hrs Low-Battery Trickle Charge Time V BAT = 2.5V ● 0.75 1.125 1.5 Hrs VACPR ACPR Pin Output Low Voltage I ACPR = 5mA ● 60 105 mV (LTC4065A) IACPR ACPR Pin Input Current (LTC4065A) V CC = 4V, VACPR = 4V, VBAT = 4.5V ● 01 µA VCHRG CHRG Pin Output Low Voltage I CHRG = 5mA ● 60 105 mV ICHRG CHRG Pin Input Current V BAT = 4.5V, VCHRG = 5V ● 01 µA IC/10 End of Charge Indication Current R PROG = 2k (Note 5) ● 0.085 0.1 0.115 mA/mA Level TLIM Junction Temperature in Constant 115 °C Temperature Mode RON Power FET “ON” Resistance I BAT = 200mA 450 m Ω (Between VCC and BAT) fBADBAT Defective Battery Detection CHRG 2 Hz Pulse Frequency DBADBAT Defective Battery Detection CHRG 75 % Pulse Frequency Duty Ratio The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C. VCC = 5V, VBAT = 3.8V, VEN = 0V (LTC4065 only) unless otherwise specified. (Note 2) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC4065/LTC4065A are guaranteed to meet performance specifications from 0°C to 70°C. Specifications over the –40 °C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Failure to solder the exposed backside of the package to the PC board ground plane will result in a thermal resistance much higher than rated. Note 4: Although the LTC4065 functions properly at 3.75V, full charge current requires an input voltage greater than the desired final battery voltage per the ∆VUVCL1 specification. Note 5: IC/10 is expressed as a fraction of measured full charge current with indicated PROG resistor. Note 6: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability.

TYPICAL PERFOR A CE CHARACTERISTICS UW Battery Regulation (Float) Voltage vs Battery Charge Current IBAT (mA) VFLOAT (V) 4.19 4.20 4.21 300 500

4065 G01

4.18 4.17 4.16 100 200 400 4.22 4.23 4.24 VCC = 5V TA = 25°C RPROG = 2k TEMPERATURE (°C) –50 VFLOAT (V) 4.23

4065 G02

4.20 4.18 –2 5 0 5 0 4.17 4.16 4.24 4.22 4.21 4.19 75 100 SUPPLY VOLTAGE (V) VFLOAT (V) 4.20 4.21 4.22

4065 G03

4.19 4.18 4.16 4.5 5 5.5 4.17 4.24 4.23 TA = 25°C IBAT = 2mA RPROG = 2k Battery Regulation (Float) Voltage vs Temperature Regulated Output (Float) Voltage vs Supply Voltage Charge Current vs Supply Voltage (Constant Current Mode) Charge Current vs Battery Voltage Charge Current vs Temperature with Thermal Regulation (Constant Current Mode) SUPPLY VOLTAGE (V) IBAT (mA) 100 125 150 175 200 4.5 5 5.5 6

4065 G04

RPROG = 10k VBAT = 3.8V TA = 25°C VBAT (V) IBAT (mA) 100 200 300 400 500 600 1234

4065 G05

VCC = 5V TA = 25°C RPROG = 2k TEMPERATURE (°C) –50 IBAT (mA) 100 200 300 400 05 0 100 150

4065 G06

VCC = 5V VBAT = 3.8V RPROG = 2k PROG Pin Voltage vs Temperature (Constant Current Mode) PROG Pin Voltage vs Charge Current Power FET On Resistance vs Temperature TEMPERATURE (°C) –50 VPROG (V) 1.01 1.02 25 75

4065 G07

1.00 –25 0 50 100 0.99 0.98 VCC = 5V VBAT = 3.8V RPROG = 10k IBAT (mA) VPROG (V) 0.2 0.4 0.6 0.8 1.0 1.2 100 200 300 400

4065 G08

VCC = 5V TA = 25°C RPROG = 2k TEMPERATURE (°C) –50

300 RDS (mΩ)

–25 02 5 5 0

4065 G09

VCC = 4V IBAT = 400mA

TYPICAL PERFOR A CE CHARACTERISTICS UW CHRG Pin Output Low Voltage vs Temperature Manual Shutdown Threshold Voltage vs Temperature (LTC4065) Manual Shutdown Supply Current vs Temperature TEMPERATURE (°C) –50 100 140 25 75

4065 G10

–25 0 50 100 120VCHRG (mV) VCC = 5V ICHRG = 5mA TEMPERATURE (°C) –50 –25 0.5 VMS (V) 0.7 1.0 0 50 75

4065 G11

0.6 0.9 0.8 25 100 FALL RISE TEMPERATURE (°C) –50 ICCMS (µA) –25 0 25 50

4065 G12

VCC = 5V VEN = 5V EN Pin Current (LTC4065) Trickle Charge Current vs Supply Voltage VEN (V) IEN (µA) 1.5 2.0 2.5 3.5 4.5

4065 G13

1.0 0.5 2.5 3 4 3.0 3.5 4.0 VCC = 5V TA = 25°C SUPPLY VOLTAGE (V) IBAT (mA) 4.5 5 5.5 6

4065 G14

RPROG = 2k RPROG = 10k VBAT = 2V TA = 25°C Trickle Charge Current vs Temperature TEMPERATURE (°C) –50 IBAT (mA) 25 75

4065 G15

–25 0 50 100 RPROG = 2k RPROG = 10k VCC = 5V VBAT = 2V ACPR Pin Output Low Voltage vs Temperature (LTC4065A Only) Undervoltage Lockout Threshold Voltage vs Temperature TEMPERATURE (°C) –50 2.5 VCC (V) 2.8 3.0 3.3 3.5 4.0 –25 02 5 RISE FALL

4065 G16

3.8 TEMPERATURE (°C) –50 100 140 25 75

4065 G17

–25 0 50 100 120VACPR (mV) VCC = 5V IACPR = 5mA

TYPICAL PERFOR A CE CHARACTERISTICS UW Timer Accuracy vs Temperature Timer Accuracy vs Supply Voltage PROG Pin Shutdown Threshold vs Temperature (LTC4065A Only) PROG Pin Shutdown Voltage vs Supply Voltage (LTC4065A Only) TEMPERATURE (°C) –50 TIMER ACCURACY (%) 25 75

4065 G18

–25 0 50 100 VCC = 5V SUPPLY VOLTAGE (V) TIMER ACCURACY (%) 1.0

4065 G19

–1.0 –2.0 4.5 5 5.5 2.0 –0.5 0.5 –1.5 1.5 TA = 25°C TEMPERATURE (°C) –50 3.0 VRMS(PROG) (V) 3.5 4.0 4.5 5.0 –25 0 25 50

4065 G20

VCC = 5V SUPPLY VOLTAGE (V) VMS(PROG) (V) 2.0 3.0 4.0 5.0 2.5 3.5 4.5 4.5 5 5.5

4065 G21

TA = 25°C

GND (Pin 1): Ground. CHRG (Pin 2): Open-Drain Charge Status Output. The charge status indicator pin has three states: pull-down, pulse at 2Hz and high impedance state. This output can be used as a logic interface or as an LED driver. When the battery is being charged, the CHRG pin is pulled low by an internal N-channel MOSFET. When the charge current drops to 10% of the full-scale current, the CHRG pin is forced to a high impedance state. If the battery voltage remains below 2.9V for one quarter of the charge time, the battery is considered defective and the CHRG pin pulses at a frequency of 2Hz. BAT (Pin 3): Charge Current Output. Provides charge current to the battery and regulates the final float voltage to 4.2V. An internal precision resistor divider on this pin sets the float voltage and is disconnected in shutdown mode. V CC (Pin 4): Positive Input Supply Voltage. This pin provides power to the charger. VCC can range from 3.75V to 5.5V. This pin should be bypassed with at least a 1 µF capacitor. When V CC is within 32mV of the BAT pin voltage, the LTC4065 enters shutdown mode, dropping IBAT to about 1µA. EN (Pin 5, LTC4065 Only): Enable Input Pin. Pulling this pin above the manual shutdown threshold (V MS is typi- cally 0.82V) puts the LTC4065 in shutdown mode. In shutdown mode, the LTC4065 has less than 20µA supply current and less than 1µA battery drain current. Enable is the default state, but the pin should be tied to GND if unused. ACPR (Pin 5, LTC4065A Only): Open-Drain Power Supply Status Output. When VCC is greater than the undervoltage lockout threshold (3.6V) and VBAT + 80mV (if VBAT > 3.6V), the ACPR pin will be pulled down to ground; otherwise the pin is high impedance. PROG (Pin 6): Charge Current Program and Charge Cur- rent Monitor Pin. Connecting a 1% resistor, R PROG, to ground programs the charge current. When charging in constant-current mode, this pin servos to 1V. In all modes, the voltage on this pin can be used to measure the charge current using the following formula: I V RBAT PROG PROG = • 1000 Floating the PROG pin sets the charge current to zero (LTC4065) or puts the part in shutdown mode (LTC4065A). In shutdown mode, the LTC4065A has less than 20 µA supply current and about 1µA battery drain current. Exposed Pad (Pin 7): Ground. The Exposed Pad must be soldered to the PCB ground to provide both electrical con- tact and rated thermal performance.

SI PLIFIEDW BLOCK DIAGRA SW MP ×1000 VCC VCC ENABLE RENB 2.9V CHRG PROG GND

4056 F01a

0.82V C/10 TA TDIE 115°C 0.1V 1.2V SHUTDOWN 0.1V 3.6V 1.2V REF CA MA LOBAT

5 EN –

Figure 1a. LTC4065 Block Diagram

SI PLIFIEDW BLOCK DIAGRA SW Figure 1b. LTC4065A Block Diagram MP ×1000 VCC VCC ENABLE 2.9V CHRG PROG GND

4056 F01b

0.1V 1.2V VBAT + 80mV 3.6V 0.1V TDIE 115°C 1.2V REF CA MA LOBAT VA

5 ACPR

The LTC4065 is a linear battery charger designed primarily for charging single cell lithium-ion batteries. Featuring an internal P-channel power MOSFET, the charger uses a constant-current/constant-voltage charge algorithm with programmable current. Charge current can be programmed up to 750mA with a final float voltage accuracy of ±0.6%. The CHRG open-drain status output indicates if C/10 has been reached. No blocking diode or external sense resistor is required; thus, the basic charger circuit requires only two external components. The ACPR pin (LTC4065A) monitors the status of the input voltage with an open-drain output. An internal termination timer and trickle charge low-battery conditioning adhere to battery manufacturer safety guidelines. Furthermore, the LTC4065 is capable of operating from a USB power source. An internal thermal limit reduces the programmed charge current if the die temperature attempts to rise above a preset value of approximately 115°C. This feature protects the LTC4065 from excessive temperature and allows the user to push the limits of the power handling capability of a given circuit board without risk of damaging the LTC4065 or external components. Another benefit of the LTC4065 thermal limit is that charge current can be set according to

typical, not worst-case, ambient temperatures for a given application with the assurance that the charger will auto- matically reduce the current in worst-case conditions. The charge cycle begins when the following conditions are met: the voltage at the VCC pin exceeds 3.6V and approxi- mately 80mV above the BAT pin voltage, a program resistor is present from the PROG pin to ground and the EN pin (LTC4065 only) is pulled below the shutdown thresh- old (typically 0.82V). If the BAT pin voltage is below 2.9V, the charger goes into trickle charge mode, charging the battery at one-tenth the programmed charge current to bring the cell voltage up to a safe level for charging. If the BAT pin voltage is above 4.1V, the charger will not charge the battery as the cell is near full capacity. Otherwise, the charger goes into the fast charge constant-current mode. When the BAT pin approaches the final float voltage (4.2V), the LTC4065 enters constant-voltage mode and the charge current begins to decrease. When the current drops to 10% of the full-scale charge current, an internal comparator turns off the N-channel MOSFET on the CHRG pin and the pin assumes a high impedance state. An internal timer sets the total charge time, t TIMER (typi- cally 4.5 hours). When this time elapses, the charge cycle terminates and the CHRG pin assumes a high impedance state. To restart the charge cycle, remove the input voltage and reapply it, momentarily force the EN pin above V MS (typically 0.82V) for LTC4065, or momentarily float the PROG pin and reconnect it (LTC4065A). The charge cycle will automatically restart if the BAT pin voltage falls below V RECHRG (typically 4.1V). When the input voltage is not present, the battery drain current is reduced to less than 4µA. The LTC4065 can also be shut down by pulling the EN pin above the shutdown threshold voltage. To put LTC4065A in shutdown mode, float the PROG pin. This reduces input quiescent current to less than 20µA and battery drain current to less than 1µA. Programming Charge Current The charge current is programmed using a single resistor from the PROG pin to ground. The battery charge current is 1000 times the current out of the PROG pin. The program resistor and the charge current are calculated using the following equations: R V I I V RPROG CHG CHG PROG ==1000 1 1000•, The charge current out of the BAT pin can be determined at any time by monitoring the PROG pin voltage and using the following equation: I V RBAT PROG PROG = • 1000 Undervoltage Lockout (UVLO) An internal undervoltage lockout circuit monitors the input voltage and keeps the charger in undervoltage lockout until V CC rises above 3.6V and approximately 80mV above the BAT pin voltage. The 3.6V UVLO circuit has a built-in hysteresis of approximately 0.6V and the automatic shut- down threshold has a built-in hysteresis of approximately 50mV. During undervoltage lockout conditions, maxi- mum battery drain current is 4 µA and maximum supply current is 11µA. Shutdown Mode The LTC4065 can be disabled by pulling the EN pin above the shutdown threshold (approximately 0.82V). The LTC4065A can be disabled by floating the PROG pin. In shutdown mode, the battery drain current is reduced to less than 1µA and the supply current to about 20µA. Timer and Recharge The LTC4065 has an internal termination timer that starts when an input voltage greater than the undervoltage lockout threshold is applied to V CC, or when leaving shutdown the battery voltage is less than the recharge threshold. At power-up or when exiting shutdown, if the battery voltage is less than the recharge threshold, the charge time is set to 4.5 hours. If the battery voltage is greater than the recharge threshold at power-up or when exiting shut- down, the timer will not start and charging is prevented since the battery is at or near full capacity.

Once the charge cycle terminates, the LTC4065 continu- ously monitors the BAT pin voltage using a comparator with a 2ms filter time. When the average battery voltage falls below 4.1V (which corresponds to 80% to 90% battery capacity), a new charge cycle is initiated and a 2.25 hour timer begins. This ensures that the battery is kept at, or near, a fully charged condition and eliminates the need for periodic charge cycle initiations. The CHRG output assumes a strong pull-down state during recharge cycles until C/10 is reached when it transitions to a high impendance state. Trickle Charge and Defective Battery Detection At the beginning of a charge cycle, if the battery voltage is low (below 2.9V), the charger goes into trickle charge, reducing the charge current to 10% of the full-scale current. If the low-battery voltage persists for one quarter of the total time (1.125 hour), the battery is assumed to be defective, the charge cycle is terminated and the CHRG pin output pulses at a frequency of 2Hz with a 75% duty cycle. If for any reason the battery voltage rises above 2.9V, the charge cycle will be restarted. To restart the charge cycle (i.e., when the defective battery is replaced with a dis- charged battery), simply remove the input voltage and reapply it, temporarily pull the EN pin above the shutdown threshold (LTC4065), or momentarily float the PROG pin and reconnect it (LTC4065A). CHRG Status Output Pin The charge status indicator pin has three states: pull- down, pulse at 2Hz (see Trickle Charge and Defective Battery Detection) and high impedance. The pull-down state indicates that the LTC4065 is in a charge cycle. A high impedance state indicates that the charge current has dropped below 10% of the full-scale current or the LTC4065 is disabled. Figure 2 shows the CHRG status under various conditions. Power Supply Status Indicator (ACPR, LTC4065A Only) The power supply status output has two states: pull-down and high impedance. The pull-down state indicates that V CC is above the undervoltage lockout threshold (see Undervoltage Lockout). When this condition is not met, the ACPR pin is high impedance indicating that the LTC4065A is unable to charge the battery. Charge Current Soft-Start and Soft-Stop The LTC4065 includes a soft-start circuit to minimize the inrush current at the start of a charge cycle. When a charge cycle is initiated, the charge current ramps from zero to the full-scale current over a period of approximately 180 µs. Likewise, internal circuitry slowly ramps the charge cur- rent from full-scale to zero when the charger is shut off or self terminates. This has the effect of minimizing the transient current load on the power supply during start-up and charge termination. Constant-Current/Constant-Voltage/ Constant-Temperature The LTC4065/LTC4065A use a unique architecture to charge a battery in a constant-current, constant-voltage and constant-temperature fashion. Figures 1a and 1b show simplified block diagrams of the LTC4065 and LTC4065A, respectively. Three of the amplifier feedback loops shown control the constant-current, CA, constant- voltage, VA, and constant-temperature, TA modes. A fourth amplifier feedback loop, MA, is used to increase the output impedance of the current source pair; M1 and M2 (note that M1 is the internal P-channel power MOSFET). It ensures that the drain current of M1 is exactly 1000 times greater than the drain current of M2. Amplifiers CA and VA are used in separate feedback loops to force the charger into constant-current or constant- voltage mode, respectively. Diodes D1 and D2 provide priority to either the constant-current or constant-voltage loop; whichever is trying to reduce the charge current the most. The output of the other amplifier saturates low which effectively removes its loop from the system. When in constant-current mode, CA servos the voltage at the PROG pin to be precisely 1V. VA servos its inverting input to an internal reference voltage when in constant-voltage mode and the internal resistor divider, made up of R1 and R2, ensures that the battery voltage is maintained at 4.2V. The PROG pin voltage gives an indication of the charge current during constant-voltage mode as discussed in “Programming Charge Current”. OPERATIOU

indication of the charge current.

4065 F02

Figure 2. State Diagram of LTC4065 Operation

long leads (or any relatively high output impedance). voltage mode reduces the charge current further. supply at the same charge current. Figure 3. Combining Wall Adapter and USB Power

3 ICHG

6 Li-Ion

4065 F03

voltage low when the battery is disconnected. with 0.2Ω to 1Ω of series resistance.

4065 F04

Figure 4. Isolating Capacitive Load on the PROG Pin and Filtering

2.00 ±0.10 (4 SIDES) NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WCCD-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.38 ± 0.05 BOTTOM VIEW—EXPOSED PAD 0.56 ± 0.05 (2 SIDES) 0.75 ±0.05 R = 0.115 TYP 1.37 ±0.05 (2 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6)

0.200 REF

0.00 – 0.05 (DC6) DFN 1103 0.25 ± 0.05 0.50 BSC0.25 ± 0.05 1.42 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 0.61 ±0.05 (2 SIDES)1.15 ±0.05 0.675 ±0.05 2.50 ±0.05 PACKAGE OUTLINE

0.50 BSC

Furthermore, the voltage at the PROG pin will change proportionally with the charge current as discussed in the Programming Charge Current section. It is important to remember that LTC4065/LTC4065A applications do not need to be designed for worst-case thermal conditions since the IC will automatically reduce power dissipation when the junction temperature reaches approximately 115°C. Board Layout Considerations In order to deliver maximum charge current under all conditions, it is critical that the exposed metal pad on the backside of the LTC4065/LTC4065A package is soldered to the PC board ground. Correctly soldered to a 2500mm double-sided 1 oz. copper board the LTC4065/LTC4065A has a thermal resistance of approximately 60°C/W. Failure to make thermal contact between the Exposed Pad on the APPLICATIO S I FOR ATIOWU UU backside of the package and the copper board will result in thermal resistances far greater than 60 °C/W. As an example, a correctly soldered LTC4065/LTC4065A can deliver over 750mA to a battery from a 5V supply at room temperature. Without a backside thermal connection, this number could drop to less than 500mA. V CC Bypass Capacitor Many types of capacitors can be used for input bypassing; however, caution must be exercised when using multi- layer ceramic capacitors. Because of the self-resonant and high Q characteristics of some types of ceramic capaci- tors, high voltage transients can be generated under some start-up conditions, such as connecting the charger input to a live power source. For more information, refer to Application Note 88. UPACKAGE DESCRIPTIO 6-Lead Plastic DFN (2mm × 2mm) (Reference LTC DWG # 05-08-1703) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.

© LINEAR TECHNOLOGY CORPORATION 2005 LT 0406 REV B • PRINTED IN THE USA RELATED PARTS Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com PART NUMBER DESCRIPTION COMMENTS Battery Chargers LTC1734 Lithium-Ion Linear Battery Charger in ThinSOT TM Simple ThinSOT Charger, No Blocking Diode, No Sense Resistor Needed LTC1734L Lithium-Ion Linear Battery Charger in ThinSOT Low Current Version of LTC1734, 50mA ≤ ICHRG ≤ 180mA LTC4002 Switch Mode Lithium-Ion Battery Charger Standalone, 4.7V ≤ VIN ≤ 24V, 500kHz Frequency, 3 Hour Charge Termination LTC4050 Lithium-Ion Linear Battery Charger Controller Features Preset Voltages, C/10 Charger Detection and Programmable Timer, Input Power Good Indication, Thermistor Interface LTC4052 Monolithic Lithium-Ion Battery Pulse Charger No Blocking Diode or External Power FET Required, ≤1.5A Charge Current LTC4053 USB Compatible Monolithic Li-Ion Battery Charger Standalone Charger with Programmable Timer, Up to 1.25A Charge Current LTC4054 Standalone Linear Li-Ion Battery Charger Thermal Regulation Prevents Overheating, C/10 Termination, with Integrated Pass Transistor in ThinSOT C/10 Indicator, Up to 800mA Charge Current LTC4057 Lithium-Ion Linear Battery Charger Up to 800mA Charge Current, Thermal Regulation, ThinSOT Package LTC4058 Standalone 950mA Lithium-Ion Charger in DFN C/10 Charge Termination, Battery Kelvin Sensing, ±7% Charge Accuracy LTC4059 900mA Linear Lithium-Ion Battery Charger 2mm × 2mm DFN Package, Thermal Regulation, Charge Current Monitor Output LTC4059A 900mA Linear Lithium-Ion Battery Charger 2mm × 2mm DFN Package, Thermal Regulation, Charge Current Monitor Output, ACPR Function LTC4061 Standalone Li-Ion Charger with Thermistor Interface 4.2V, ±0.35% Float Voltage, Up to 1A Charge Current, 3mm × 3mm DFN LTC4061-4.4 Standalone Li-Ion Charger with Thermistor Interface 4.4V (Max), ±0.4% Float Voltage, Up to 1A Charge Current, 3mm × 3mm DFN LTC4062 Standalone Linear Li-Ion Battery Charger with 4.2V, ±0.35% Float Voltage, Up to 1A Charge Current, 3mm × 3mm DFN Micropower Comparator LTC4063 Li-Ion Charger with Linear Regulator Up to 1A Charge Current, 100mA, 125mV LDO, 3mm × 3mm DFN LTC4411/LTC4412 Low Loss PowerPath TM Controller in ThinSOT Automatic Switching Between DC Sources, Load Sharing, Replaces ORing Diodes Power Management LTC3405/LTC3405A 300mA (I OUT), 1.5MHz, Synchronous Step-Down 95% Efficiency, V IN: 2.7V to 6V, VOUT = 0.8V, IQ = 20µA, ISD < 1µA, DC/DC Converter ThinSOT Package LTC3406/LTC3406A 600mA (I OUT), 1.5MHz, Synchronous Step-Down 95% Efficiency, V IN: 2.5V to 5.5V, VOUT = 0.6V, IQ = 20µA, ISD < 1µA, DC/DC Converter ThinSOT Package LTC3411 1.25A (I OUT), 4MHz, Synchronous Step-Down 95% Efficiency, V IN: 2.5V to 5.5V, VOUT = 0.8V, IQ = 60µA, ISD < 1µA, DC/DC Converter MS Package LTC3440 600mA (I OUT), 2MHz, Synchronous Buck-Boost 95% Efficiency, V IN: 2.5V to 5.5V, VOUT = 2.5V, IQ = 25µA, ISD < 1µA, DC/DC Converter MS Package LTC4413 Dual Ideal Diode in DFN 2-Channel Ideal Diode ORing, Low Forward ON Resistance, Low Regulated Forward Voltage, 2.5V ≤ VIN ≤ 5.5V ThinSOT and PowerPath are trademarks of Linear Technology Corporation.