LM675 Power Operational Amplifier datasheet (Rev. E)
Document overview
- Manufacturer or author: Texas Instruments, Incorporated [SNOSBP3,E]
- PDF pages: 17
Technical content
www.ti.com SNOSBP3E –MAY 1999–REVISED MARCH 2013 LM675PowerOperationalAmplifier Check forSamples: LM675 1FEATURES Connection Diagram 2• 3A CurrentCapability
- A VO Typically90 dB
- 5.5MHz Gain Bandwidth Product
- 8 V/μs Slew Rate
- Wide Power Bandwidth 70 kHz
- 1 mV TypicalOffsetVoltage *The tabisinternallyconnectedtopin3
- ShortCircuitProtection (−VEE )
- Thermal ProtectionwithParoleCircuit(100% Figure1. FrontView Tested) TO-220 Power Package (NDH) See Package Number NDH0005D• 16V–60V Supply Range
- Wide Common Mode Range
- InternalOutput ProtectionDiodes TypicalApplications
- 90 dB RippleRejection
- PlasticPower Package TO-220
APPLICATIONS
- High Performance Power Op Amp
- BridgeAmplifiers
- Motor Speed Controls
- Servo Amplifiers
- InstrumentSystems
DESCRIPTION
The LM675 is a monolithicpower operational amplifierfeaturingwide bandwidth and low input offsetvoltage,making itequallysuitableforAC and DC applications. The LM675 iscapableofdeliveringoutputcurrentsin excessof3 amps, operatingatsupplyvoltagesofup to 60V. The deviceoverloadprotectionconsistsof both internalcurrentlimitingand thermalshutdown. Figure2. Non-InvertingAmplifierThe amplifierisalsointernallycompensated forgains of10 orgreater. Pleasebe aware thatan importantnoticeconcerningavailability,standardwarranty,and use incriticalapplicationsof Texas Instrumentssemiconductorproductsand disclaimerstheretoappearsattheend ofthisdatasheet. 2Alltrademarksarethepropertyoftheirrespectiveowners. PRODUCTION DATA informationiscurrentas ofpublicationdate. Copyright© 1999–2013,Texas InstrumentsIncorporatedProductsconform to specificationsper the terms of the Texas Instrumentsstandardwarranty.Productionprocessingdoes not necessarilyincludetestingofallparameters.
SNOSBP3E –MAY 1999–REVISED MARCH 2013 www.ti.com These deviceshave limitedbuilt-inESD protection.The leadsshouldbe shortedtogetherorthedeviceplacedinconductivefoam duringstorageorhandlingtopreventelectrostaticdamage totheMOS gates. ABSOLUTE MAXIMUM RATINGS (1)(2) SupplyVoltage ±30V InputVoltage −VEE toVCC OperatingTemperature 0°C to+70°C StorageTemperature −65°C to+150°C JunctionTemperature 150°C Power Dissipation(3) 30W Lead Temperature (Soldering,10 seconds) 260°C ESD ratingtobe determined. (1) AbsoluteMaximum Ratingsindicatelimitsbeyond whichdamage tothedevicemay occur.OperatingRatingsindicateconditionsfor whichthedeviceisfunctional,butdo notensurespecificperformancelimits.ElectricalCharacteristicsstateDC and AC electrical specificationsunderparticulartestconditionswhichensurespecificperformancelimits.Thisassumes thatthedeviceiswithinthe OperatingRatings.Specificationsarenotensuredforparameterswhere no limitisgiven,however,thetypicalvalueisa good indication ofdeviceperformance. (2) IfMilitary/Aerospacespecifieddevicesarerequired,pleasecontacttheTexas InstrumentsSalesOffice/Distributorsforavailabilityand specifications. (3) Assumes TA equalto70°C. Foroperationathighertabtemperatures,theLM675 must be deratedbased on a maximum junction temperatureof150°C.
ELECTRICAL CHARACTERISTICS
VS=±25V,TA=25°C unlessotherwisespecified. Parameter Conditions Typical Tested Limit Units SupplyCurrent POUT = 0W 18 50 (max) mA InputOffsetVoltage VCM = 0V 1 10 (max) mV InputBiasCurrent VCM = 0V 0.2 2 (max) μA InputOffsetCurrent VCM = 0V 50 500 (max) nA Open Loop Gain R L = ∞Ω 90 70 (min) dB PSRR ΔVS = ±5V 90 70 (min) dB CMRR VIN = ±20V 90 70 (min) dB OutputVoltageSwing R L = 8Ω ±21 ±18 (min) V OffsetVoltageDriftVersusTemperature R S < 100 kΩ 25 μV/°C OffsetVoltageDriftVersusOutputPower 25 μV/W OutputPower THD = 1%, fO = 1 kHz,R L = 8Ω 25 20 W Gain BandwidthProduct fO = 20 kHz,AVCL = 1000 5.5 MHz Max Slew Rate 8 V/μs InputCommon Mode Range ±22 ±20 (min) V
2 SubmitDocumentationFeedback Copyright© 1999–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LM675
www.ti.com SNOSBP3E –MAY 1999–REVISED MARCH 2013 TYPICAL APPLICATIONS VS = ±8V → ±30V Figure3. Generatinga SplitSupply From a SingleSupply Copyright© 1999–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 3 ProductFolderLinks:LM675
SNOSBP3E –MAY 1999–REVISED MARCH 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS THD vs Power Output InputCommon Mode Range vs Supply Voltage Figure4. Figure5. Supply Currentvs Supply Voltage PSRR vs Frequency Figure6. Figure7. Device Dissipationvs Ambient Temperature† CurrentLimitvs Output Voltage* †θ INTERFACE = 1° C/W *VS = ±25V See APPLICATION HINTS . Figure8. Figure9.
4 SubmitDocumentationFeedback Copyright© 1999–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LM675
www.ti.com SNOSBP3E –MAY 1999–REVISED MARCH 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) IB vs Supply Voltage Output VoltageSwing vs Supply Voltage Figure10. Figure11. Copyright© 1999–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 5 ProductFolderLinks:LM675
SNOSBP3E –MAY 1999–REVISED MARCH 2013 www.ti.com SCHEMATIC DIAGRAM
6 SubmitDocumentationFeedback Copyright© 1999–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LM675
www.ti.com SNOSBP3E –MAY 1999–REVISED MARCH 2013 APPLICATION HINTS STABILITY The LM675 isdesignedtobe stablewhen operatedata closed-loopgainof10 orgreater,but,as withany other high-currentamplifier,the LM675 can be made to oscillateunder certainconditions.These usuallyinvolve printedcircuitboardlayoutoroutput/inputcoupling. When designinga printedcircuitboardlayout,itisimportanttoreturntheloadground,theoutputcompensation ground,and thelow level(feedbackand input)groundstothecircuitboardgroundpointthroughseparatepaths. Otherwise,largecurrentsflowingalonga ground conductorwillgeneratevoltageson theconductorwhich can effectivelyactas signalsattheinput,resultinginhighfrequencyoscillationorexcessivedistortion.Itisadvisable tokeep theoutputcompensationcomponents and the0.1μF supplydecouplingcapacitorsas closeas possible totheLM675 toreducetheeffectsofPCB traceresistanceand inductance.For thesame reason,theground returnpathsforthesecomponents shouldbe as shortas possible. Occasionally,currentinthe outputleads(whichfunctionas antennas)can be coupledthroughthe airto the amplifierinput,resultinginhigh-frequencyoscillation.Thisnormallyhappens when thesourceimpedance ishigh ortheinputleadsarelong.The problemcan be eliminatedby placinga smallcapacitor(ontheorderof50 pF to 500 pF)acrossthecircuitinput. Most power amplifiersdo notdrivehighlycapacitiveloadswell,and theLM675 isno exception.Iftheoutputof theLM675 isconnecteddirectlytoa capacitorwithno seriesresistance,thesquarewave responsewillexhibit ringingifthecapacitanceisgreaterthanabout0.1μF.The amplifiercan typicallydriveloadcapacitancesup to2 μF or so withoutoscillating,butthisisnotrecommended. Ifhighlycapacitiveloadsare expected,a resistor(at least1Ω) shouldbe placedinserieswiththe outputof the LM675. A method commonly employed to protect amplifiersfromlowimpedancesathighfrequenciesistocoupletotheloadthrougha 10Ω resistorinparallelwith a 5 μH inductor. CURRENT LIMITAND SAFE OPERATING AREA (SOA) PROTECTION A power amplifier'soutputtransistorscan be damaged by excessiveappliedvoltage,currentflow,or power dissipation.The voltageappliedtotheamplifierislimitedby thedesignoftheexternalpower supply,whilethe maximum currentpassed by theoutputdevicesisusuallylimitedby internalcircuitrytosome fixedvalue.Short- termpower dissipationisusuallynotlimitedinmonolithicoperationalpower amplifiers,and thiscan be a problem when drivingreactiveloads,whichmay draw largecurrentswhilehighvoltagesappearon theoutputtransistors. The LM675 notonlylimitscurrenttoaround 4A, butalsoreducesthevalueofthelimitcurrentwhen an output transistorhas a highvoltageacrossit. When drivingnonlinearreactiveloadssuch as motorsor loudspeakerswithbuilt-inprotectionrelays,thereisa possibilitythatan amplifieroutputwillbe connectedto a loadwhose terminalvoltagemay attemptto swing beyond thepower supplyvoltagesappliedtotheamplifier.Thiscan cause degradationoftheoutputtransistors orcatastrophicfailureofthewhole circuit.The standardprotectionforthistypeoffailuremechanism isa pairof diodesconnectedbetween theoutputoftheamplifierand thesupplyrails.These arepartoftheinternalcircuitry oftheLM675, and needn'tbe added externallywhen standardreactiveloadsaredriven. THERMAL PROTECTION The LM675 has a sophisticatedthermalprotectionscheme to preventlong-termthermalstressto the device. When thetemperatureon thediereaches170°C, theLM675 shutsdown. Itstartsoperatingagainwhen thedie temperaturedropstoabout145°C, butifthetemperatureagainbeginstorise,shutdownwilloccuratonly150°C. Therefore,thedeviceisallowedtoheatup toa relativelyhightemperatureifthefaultconditionistemporary,but a sustainedfaultwilllimitthe maximum dietemperatureto a lowervalue.Thisgreatlyreducesthe stresses imposed on theIC by thermalcycling,whichinturnimprovesitsreliabilityundersustainedfaultconditions.This circuitryis100% testedwithouta heatsink. Sincethedietemperatureisdirectlydependentupon theheatsink,theheatsinkshouldbe chosen forthermal resistancelow enough thatthermalshutdown willnotbe reachedduringnormaloperaton.Using thebestheat sinkpossiblewithinthe costand space constraintsof the system willimprovethe long-termreliabilityof any power semiconductor. Copyright© 1999–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 7 ProductFolderLinks:LM675
SNOSBP3E –MAY 1999–REVISED MARCH 2013 www.ti.com POWER DISSIPATION AND HEAT SINKING The LM675 shouldalwaysbe operatedwitha heatsink,even thoughatidleworstcase power dissipationwillbe only1.8W (30mA × 60V) whichcorrespondstoa riseindietemperatureof97°C above ambientassuming θjA = 54°C/W fora TO-220 package.Thisinitselfwillnot cause the thermalprotectioncircuitryto shutdown the amplifierwhen operatingat room temperature,but a mere 0.9W of additionalpower dissipationwillshutthe amplifierdown sinceTJ willthenincreasefrom122°C (97°C + 25°C) to170°C. Inordertodeterminetheappropriateheatsinkfora givenapplication,thepower dissipationoftheLM675 inthat applicationmust be known. When theloadisresistive,themaximum averagepower thattheIC willbe required todissipateisapproximately: where
- VS isthetotalpower supplyvoltageacrosstheLM675
- R L istheloadresistance
- PQ isthequiescentpower dissipationoftheamplifier The above equationisonlyan approximationwhichassumes an “ideal”classB outputstageand constantpower dissipationinallotherpartsofthecircuit.As an example,iftheLM675 isoperatedon a 50V power supplywitha resistiveloadof8Ω,itcan developup to19W ofinternalpower dissipation.Ifthedietemperatureistoremain below 150°C forambienttemperaturesup to70°C, thetotaljunction-to-ambientthermalresistancemust be less than Using θJC = 2°C/W, thesum ofthecase-to-heatsinkinterfacethermalresistanceand theheat-sink-to-ambient thermalresistancemust be lessthan2.2°C/W. The case-to-heat-sinkthermalresistanceoftheTO-220 package varieswiththemountingmethod used.A metal-to-metalinterfacewillbe about1°C/W iflubricated,and about 1.2°C/W ifdry.Ifa mica insulatorisused,thethermalresistancewillbe about1.6°C/W lubricatedand 3.4°C/W dry.For thisexample,we assume a lubricatedmica insulatorbetween theLM675 and theheatsink.The heat sinkthermalresistancemust thenbe lessthan Thisisa ratherlargeheatsinkand may notbe practicalinsome applications.Ifa smallerheatsinkisrequired forreasonsof sizeor cost,thereare two alternatives.The maximum ambientoperatingtemperaturecan be restrictedto50°C (122°F),resultingina 1.6°C/W heatsink,ortheheatsinkcan be isolatedfromthechassisso themica washer isnotneeded.Thiswillchange therequiredheatsinktoa 1.2°C/W unitifthecase-to-heat-sink interfaceislubricated. The thermalrequirementscan become more difficultwhen an amplifierisdrivinga reactiveload.For a given magnitudeofloadimpedance,a higherdegreeofreactancewillcause a higherlevelofpower dissipationwithin theamplifier.As a generalrule,thepower dissipationofan amplifierdrivinga 60° reactiveloadwillbe roughly thatofthesame amplifierdrivingtheresistivepartofthatload.For example,some reactiveloadsmay atsome frequencyhave an impedance witha magnitudeof8Ω and a phase angleof60°.The realpartofthisloadwill thenbe 8Ω × cos 60° or4Ω,and theamplifierpower dissipationwillroughlyfollowthecurveofpower dissipation witha 4Ω load.
8 SubmitDocumentationFeedback Copyright© 1999–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LM675
www.ti.com SNOSBP3E –MAY 1999–REVISED MARCH 2013 TypicalApplications Figure12. Non-InvertingUnityGain Operation Figure13. InvertingUnityGain Operation Copyright© 1999–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 9 ProductFolderLinks:LM675
SNOSBP3E –MAY 1999–REVISED MARCH 2013 www.ti.com Figure14. Servo Motor Control IOUT = VIN × 2.5amps/volt i.e.IOUT = 1A when VIN = 400 mV Trimpotformax R OUT Figure15. High CurrentSource/Sink
10 SubmitDocumentationFeedback Copyright© 1999–2013,Texas InstrumentsIncorporated
ProductFolderLinks:LM675
www.ti.com SNOSBP3E –MAY 1999–REVISED MARCH 2013
REVISION HISTORY
Changes from RevisionD (March 2013)toRevisionE Page Copyright© 1999–2013,Texas InstrumentsIncorporated SubmitDocumentationFeedback 11 ProductFolderLinks:LM675
www.ti.com 11-Nov-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) LM675T Obsolete Production TO-220 (NDH) | 5 - - Call TI Call TI 0 to 70 LM675T LM675T/LF02 Active Production TO-220 (NEB) | 5 45 | TUBE Yes SN Level-1-NA-UNLIM 0 to 70 LM675T LM675T/LF02.B Active Production TO-220 (NEB) | 5 45 | TUBE Yes SN Level-1-NA-UNLIM 0 to 70 LM675T LM675T/LF05 Active Production TO-220 (NEB) | 5 45 | TUBE Yes SN Level-1-NA-UNLIM 0 to 70 LM675T LM675T/LF05.B Active Production TO-220 (NEB) | 5 45 | TUBE Yes SN Level-1-NA-UNLIM 0 to 70 LM675T LM675T/NOPB Active Production TO-220 (NDH) | 5 45 | TUBE Yes SN Level-1-NA-UNLIM 0 to 70 LM675T LM675T/NOPB.B Active Production TO-220 (NDH) | 5 45 | TUBE Yes SN Level-1-NA-UNLIM 0 to 70 LM675T (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1
www.ti.com 11-Nov-2025 Addendum-Page 2
PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2026 TUBE L - Tube length T - Tube height W - Tube width B - Alignment groove width *All dimensions are nominal Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm) LM675T/LF02 NEB TO-220 5 45 502 30 30048.2 10.74 LM675T/LF02.B NEB TO-220 5 45 502 30 30048.2 10.74 LM675T/LF05 NEB TO-220 5 45 502 30 30048.2 10.74 LM675T/LF05.B NEB TO-220 5 45 502 30 30048.2 10.74 LM675T/NOPB NDH TO-220 5 45 502 30 30048.2 10.74 LM675T/NOPB.B NDH TO-220 5 45 502 30 30048.2 10.74 Pack Materials-Page 1
www.ti.com
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2026, Texas Instruments Incorporated Last updated 10/2025