L1T2-2780000000000

L1T2-3070000000000_14 ETC2

Document overview

• PDF pages: 19

Technical content

Page 1

LUXEON TX

Extreme efficacy that will transform your next market leading luminaire

Introduction

LUXEON TX emitters are illumination grade LEDs designed to deliver high efficacy with high flux density

to enable directional and high-lumen applications. With Freedom from Binning and extreme performance,

LUXEON TX emitters ensure system color point accuracy and provide lamp and luminaire designers with the

flexibility to optimize for the highest possible efficacy or for low system cost, in vast Correlated Color Temperature

(CCT) ranges at 70 CRI from 3000K to 6500K, at 80 and 85 CRI from 2700K to 5000K, and at 90 CRI from 2700K

to 3000K.

LUXEON TX Datasheet DS133 ©2014 Philips Lumileds Lighting Company.

Page 2

Table of Contents

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Average Lumen Maintenance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Product Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Solder Pad Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Typical Relative Spectral Distribution vs. Wavelength Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Typical Relative Light Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Typical Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Emitter Pocket Tape Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Emitter Reel Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Product Binning and Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

LUXEON TX 3-step and 5-step MacAdam Ellipse Color Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

i

Page 3

General Information

Product Nomenclature

LUXEON TX emitters are specified and binned “hot” under conditions comparable to those found in “real-world” lighting products. The test conditions for LUXEON TX are 700 mA DC with junction temperature at 85°C.

The base part number designation is explained as follows:

L 1 T 2 – x x y y s 0 0 0 0 z z z 0

Where:

designates nominal ANSI CCT (27 for 2700K, 30 for 3000K)

xx —

designates minimum CRI performance (70 for 70 CRI, 80 for 80 CRI)

yy —

designates SDCM (0 for full distribution, 3 for 3-step SDCM, 5 for 5-step SDCM)

s —

designates minimum flux level at standard binning current and temperature (210 for 210 lm, etc.)

zzz —

Therefore, 80 CRI 3-step SDCM products tested and binned at 3000K with a 210 lm minimum flux at binning current and temperature will have the part numbering scheme:

L 1 T 2 – 3 0 8 0 3 0 0 0 0 2 1 0 0

The base part numbers referred to in this document in the following format indicate full flux and color distribution:

L 1 T 2 – x x y y 0 0 0 0 0 0 0 0 0

Average Lumen Maintenance Characteristics

LUXEON TX products are tested in compliance with LM-80. Please visit the LM-80 documentation site at www.philipslumileds.com/support/documentation/lumen-maintenance or contact your local Philips Lumileds Technical Solutions Manager for TM-21 extrapolations or other support.

Environmental Compliance

Philips Lumileds is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON TX complies with the European Union directives on the restriction of hazardous substances in electronic equipment, namely the RoHS and REACH directives. Philips Lumileds will not intentionally add the following restricted material to the LUXEON TX: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE).

Page 4

Product Selection

Product Selection Guide for LUXEON TX Emitters, Junction Temperature = 85°C

Table 1.

L1T2-3070000000000 3000K

70

230

135 245 327 2.71 2.80 2.86 142 125 114

L1T2-4070000000000 4000K

70

250

147 269 360 2.71 2.80 2.86 155 137 126

L1T2-5070000000000 5000K

70

260

151 275 369 2.71 2.80 2.86 159 140 129

L1T2-5770000000000 5700K

70

260

151 275 369 2.71 2.80 2.86 159 140 129

L1T2-6570000000000 6500K

70

260

151 275 369 2.71 2.80 2.86 159 140 129

L1T2-2780000000000 2700K

80

200

118 216 289 2.71 2.80 2.86 124 110 101

L1T2-3080000000000 3000K

80

210

124 227 304 2.71 2.80 2.86 131 116 106

L1T2-3580000000000 3500K

80

220

130 238 319 2.71 2.80 2.86 137 121 112

L1T2-4080000000000 4000K

80

230

136 247 332 2.71 2.80 2.86 143 126 116

L1T2-5080000000000 5000K

80

230

136 247 332 2.71 2.80 2.86 143 126 116

L1T2-2785000000000 2700K

85

170

102 186 249 2.71 2.80 2.86 108 95 87

L1T2-3085000000000 3000K

85

180

108 197 264 2.71 2.80 2.86 114 101 92

L1T2-3585000000000 3500K

85

190

114 208 279 2.71 2.80 2.86 120 106 98

L1T2-4085000000000 4000K

85

200

120 217 292 2.71 2.80 2.86 127 111 102

L1T2-5085000000000 5000K

85

200

120 217 292 2.71 2.80 2.86 127 111 102

L1T2-2790000000000 2700K

90

160

96 175 234 2.71 2.80 2.86 101 89 82

L1T2-3090000000000 3000K

90

170

103 188 252 2.71 2.80 2.86 109 96 88

Notes for Table 1: 1. Philips Lumileds maintains a tolerance of ± 6.5% on luminous flux and ± 2 on CRI measurements.

Page 5

Optical Characteristics

LUXEON TX at 700 mA, Junction Temperature = 85°C

Table 2.

L1T2-2780000000000 L1T2-2785000000000

2700K

2725K

160

120

L1T2-2790000000000 L1T2-3070000000000 L1T2-3080000000000

3000K

3045K

160

120

L1T2-3085000000000 L1T2-3090000000000 L1T2-3580000000000

3500K

3465K

160

120

L1T2-3585000000000 L1T2-4070000000000 L1T2-4080000000000

4000K

3985K

160

120

L1T2-4085000000000 L1T2-5070000000000 L1T2-5080000000000

5000K

5028K

160

120

L1T2-5085000000000 L1T2-5770000000000

5700K

5665K

160

120

L1T2-6570000000000

6500K

6530K

160

120

Notes for Table 2: 1. Test current is 700 mA D.C. for all L1T2-xxyy000000000 emitters. 2. Total angle at which 90% of total luminous flux is captured. 3. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.

Page 6

Electrical Characteristics

Electrical Characteristics at 700 mA for LUXEON TX Junction Temperature = 85°C

Table 3.

L1T2-2780000000000

2700K

L1T2-2785000000000

2.5

L1T2-2790000000000 L1T2-3070000000000 L1T2-3080000000000

3000K

2.5

L1T2-3085000000000 L1T2-3090000000000 L1T2-3580000000000

3500K

2.5

L1T2-3585000000000 L1T2-4070000000000

4000K

L1T2-4080000000000

2.5

L1T2-4085000000000 L1T2-5070000000000

5000K

L1T2-5080000000000

2.5

L1T2-5085000000000

5700K

L1T2-5770000000000

2.5

6500K

L1T2-6570000000000

2.5

Notes for Table 3: 1. Philips Lumileds maintains a tolerance of ±0.06V on forward voltage measurements. 2. Measured between Tj = 25°C and TJ = 110°C at If = 700 mA.

Absolute Maximum Ratings

Table 4.

Parameter

DC Forward Current [1] [2] Peak Pulsed Forward Current [1] [3] LED Junction Temperature [1] ESD Sensitivity

Operating Case Temperature at 700 mA

Storage Temperature Soldering Temperature Allowable Reflow Cycles Reverse Voltage (Vr) [4] [5]

Notes for Table 4:

3.0

-1.6

3

3.0

-1.6

3

3.0

-1.6

3

3.0

-1.6

3

3.0

-1.6

3

3.0

-1.6

3

3.0

-1.6

3

LUXEON TX

1050 mA

1200 mA

1200 mA

1350 mA

150°C

135°C

< 8000V Human Body Model (HBM) Class 3A per JEDEC JS-001-2012

-40°C - 135°C

-40°C - 135°C JEDEC 020c 260°C 3

LUXEON TX LEDs are not designed to be driven in reverse bias

1. Proper current derating must be observed to maintain junction temperature below the maximum. For additional information on thermal measurement guidelines please refer to Application Brief AB106. 2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple”, with frequencies ≥100 Hz and amplitude ≤ 150 mA are acceptable, assuming the average current throughout each cycle does not exceed the maximum allowable DC Forward Current at the corresponding maximum junction temperature. 3. Pulsed operation with a peak drive current equal to the stated Peak Pulsed Forward Current is acceptable if the pulse on-time is ≤ 5 ms per cycle and the duty cycle is ≤ 50%.

1. Transient reverse voltages and surge currents due to electrical switching or supply interruptions are acceptable if these events do not last for more than 10ms, the amplitude of the reverse voltage does not exceed 5V and the reverse current is less than 200μA. 5. Max 5V reverse for up to 10s is an acceptable beginning of life, one time test condition.

Page 7

JEDEC Moisture Sensitivity

Table 5.

168h

85°C / 85%

[ 30°C /

1

unlimited

+ 5 / - 0

RH

85% RH

Reflow Soldering Characteristics

Figure 1. Temperature profile for Table 6.

Table 6.

Profile Feature

Average Ramp-Up Rate ( Tsmax to Tp )

Preheat Temperature Min ( Tsmin )

Preheat Temperature Max ( Tsmax )

Preheat Time ( tsmin to tsmax )

Liquidus Temperature ( TL )

Time Maintained Above Time ( tL )

Peak / Classification Temperature ( TP )

Time Within 5°C of Actual Peak Temperature ( tP )

Ramp-Down Rate

Time 25°C to Peak Temperature

Lead Free Assembly

3°C / second max

150°C

200°C

60 - 180 seconds

217°C

60 - 150 seconds

260°C

20 - 40 seconds

6°C / second max

8 minutes max

Page 8

Mechanical Dimensions

Notes for Figure 2: 1. Do not handle the device by the lens. Excessive force on the lens may damage the lens itself or the interior of the device. 2. Drawings not to scale. 3. All dimensions are in millimeters. 4. The thermal pad is electrically isolated from the anode and cathode contact pads.

Page 9

Solder Pad Design

X X

Figure 3. Solder pad layout.

Notes for Figure 3: 1. All dimensions are in millimeters. 2. The figure shows the recommended LUXEON TX layout on Printed Circuit Board (PCB). 3. For more information on assembly and layout, please refer to Application Brief 106 (AB106). 4. The .dwg files are available at www.philipslumileds.com and www.philipslumileds.cn.com.

Page 10

Typical Relative Spectral Distribution vs. Wavelength Characteristics

L1T2-xx70000000000 (70 CRI, White) at Test Current, Junction Temperature = 85°C

Figure 4. Color Spectrum of L1T2-xx70000000000.

L1T2-xx80000000000 (80 CRI, White) at Test Current, Junction Temperature = 85°C

Figure 5. Color Spectrum of L1T2-xx80000000000.

Page 11

Typical Relative Spectral Distribution vs. Wavelength Characteristics, Continued

L1T2-xx90000000000 (90 CRI, White) at Test Current, Junction Temperature = 85°C

Figure 6. Color Spectrum of L1T2-xx90000000000.

Page 12

Typical Relative Light Output

Typical Relative Light Output vs. Junction Temperature for L1T2-xxyy000000000 (White), Test Current = 700 mA

Figure 7. Typical relative light output vs. junction temperature, L1T2-xxyy000000000.

Typical Relative Light Output vs . Forward Current for L1T2-xxyy000000000 (White), Junction Temperature = 85°C

Figure 8. Typical relative luminous flux vs. forward current, L1T2-xxyy000000000.

Page 13

Typical Forward Current Characteristics

Forward Current vs. Forward Voltage for L1T2-xxyy000000000 (White) Junction Temperature = 85°C

Figure 9. Typical forward current vs. forward voltage, L1T2-xxyy000000000.

Page 14

Emitter Pocket Tape Packaging

-LEADER- 400mm MIN OF COVER TAPE

-TRAILER-

5.50±0.05

Figure 10. Emitter pocket tape packaging.

Page 15

Emitter Reel Packaging

-DEVICE OREINTATION- NON-FIDUCIAL CORNER LOCATED AS SHOWN

DETAIL L SCALE 6 : 1

16.8mm OUTSIDE WIDTH

12.4mm INSIDE WIDTH

Figure 11. Emitter reel packaging.

DS106 LUXEON T 20130630 ©2013 Philips Lumileds Lighting Company.

Page 16

Product Binning and Labeling

Purpose of Product Binning

In the manufacturing of semiconductor products, there are variations in performance around the average values given in the technical data sheets. For this reason, Philips Lumileds bins the LED components for luminous flux and forward voltage (Vf). Color is offered in a single 3-step or 5-step MacAdam ellipse color space centered on the ANSI CCT color bins. For additional information please review the MacAdam ellipse technical definition section.

Decoding Product Bin Labeling

LUXEON TX emitters are labeled using a four digit alphanumeric CAT code following the format below:

ABCD

Page 17

Product Binning and Labeling, Continued

Table 7 lists the standard photometric luminous flux bins for LUXEON TX emitters (tested and binned at 700 mA and Tj = 85°C). Although several bins are outlined, product availability in a particular bin varies by production run and by product performance.

Not all bins are available in all colors.

Table 7. Flux Bins – White

Minimum Photometric Flux

Bin Code

(lm)

G

160

H

170

J

180

K

190

L

200

M

210

N

220

P

230

Q

240

R

250

S

260

T

270

U

280

V

290

W

300

Page 18

LUXEON TX 3-step and 5-step MacAdam Ellipse Color Definition

Tested at 700 mA DC and Junction Temperature = 85°C

Table 8. LUXEON TX Product Characteristics for 3-step MacAdam Ellipse Nominal

Center Point

Color Space

ANSI CCT

(cx, cy)

2700K

Single 3-step MacAdam ellipse

(0.4578, 0.4101)

3000K

Single 3-step MacAdam ellipse

(0.4338, 0.4030)

3500K

Single 3-step MacAdam ellipse

(0.4073, 0.3917)

4000K

Single 3-step MacAdam ellipse

(0.3818, 0.3797)

5000K

Single 3-step MacAdam ellipse

(0.3447, 0.3553)

Table 9. LUXEON TX Product Characteristics for 5-step MacAdam Ellipse Nominal

Center Point

Color Space

ANSI CCT

(cx, cy)

2700K

Single 5-step MacAdam ellipse

(0.4578, 0.4101)

3000K

Single 5-step MacAdam ellipse

(0.4338, 0.4030)

3500K

Single 5-step MacAdam ellipse

(0.4073, 0.3917)

4000K

Single 5-step MacAdam ellipse

(0.3818, 0.3797)

5000K

Single 5-step MacAdam ellipse

(0.3447, 0.3553)

5700K

Single 5-step MacAdam ellipse

(0.3287, 0.3417)

6500K

Single 5-step MacAdam ellipse

(0.3123, 0.3282)

Note for Tables 8 & 9: 1. Philips Lumileds maintains a tester tolerance of ± 0.005 on x, y color coordinates.

Major Axis,

Minor Axis,

Ellipse

a

b

Rotation Angle

0.00810

0.00420

53.7°

0.00834

0.00408

53.2°

0.00927

0.00414

54.0°

0.00939

0.00402

53.7°

0.00822

0.00354

59.6°

Major Axis,

Minor Axis,

Ellipse

a

b

Rotation Angle

0.01350

0.00700

53.7°

0.01390

0.00680

53.2°

0.01545

0.00690

54.0°

0.01565

0.00670

53.7°

0.01370

0.00590

59.6°

0.01243

0.00533

59.1°

0.01115

0.00475

58.6°

Page 19

Who We Are

Philips Lumileds focuses on one goal: Creating the world’s highest performing LEDs. The company pioneered the use

of solid-state lighting in breakthrough products such as the first LED backlit TV, the first LED flash in camera phones,

and the first LED daytime running lights for cars. Today we offer the most comprehensive portfolio of high quality

LEDs and uncompromising service.

Philips Lumileds brings LED’s qualities of energy efficiency, digital control and long life to spotlights, downlights,

high bay and low bay lighting, indoor area lighting, architectural and specialty lighting as well as retrofit lamps. Our

products are engineered for optimal light quality and unprecedented efficacy at the lowest overall cost. By offering

LEDs in chip, packaged and module form, we deliver supply chain flexibility to the inventors of next generation

illumination.

Philips Lumileds understands that solid state lighting is not just about energy efficiency. It is about elegant design.

Reinventing form. Engineering new materials. Pioneering markets and simplifying the supply chain. It’s about a

shared vision. Learn more about our comprehensive portfolio of LEDs at www.philipslumileds.com.

RoHS COMPLIANT No. E352519

Philips Lumileds Lighting Company shall not be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. Although Philips Lumileds Lighting Company has attempted to provide the most accurate information and data, the materials and services information and data are provided “as is” and Philips Lumileds Lighting Company neither warranties, nor guarantees the contents and correctness of the provided information and data. Philips Lumileds Lighting Company reserves the right to make changes without notice. You as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data.

©2014 Philips Lumileds Lighting Company. All rights reserved. LUXEON is a registered trademark of the Philips Lumileds Lighting Company in the United States and other countries. www.philipslumileds.com

LUXEON TX Datasheet DS133 20140224

www.philipslumileds.cn.com