L1314 HAMAMATSU

Document overview

  • PDF pages: 2

Technical content

Page 1

PDF page 1 diagram

High Intensity, 150 W Type,

Vacuum UV (from 115 nm) Light Source - L1835

The L1314 and L1835 are water-cooled 150 W deuterium lamps that deliver a radiant intensity 3 to 4 times higher than standard 30 W deuterium lamps. The lamp bulb is enclosed in a cylindrical metal jacket specially designed for water cooling. The L1314 has a synthetic silica window for an efficient emission of UV radiation, and the L1835 em- ploys a MgF2 (magnesium fluoride) window which even allows emitting vacuum UV radiation. Select the lamp that matches wavelengths required by your application. Vacuum flanges are also available as op- tions in the L1835 for easy mounting to a vacuum chamber.

APPLICATIONS

GSpectrophotometer, Fluorescence Spectrophotometer GRemoval of static electricity from the semiconductor wafer GPID (Photo Ionization Detector) GSolar Simulator GOptical CVD GOptical Chemical Reaction GExcitation Light Source

SPECIFICATIONS

GENERAL

Parameter L1314 L1835 Unit
Spectral Distribution 160 to 400 115 to 400 nm
Window Material Synthetic silica MgF2 —
Aperture Size 2.5 mm dia.
Cooling Method Water cooling A —
Weight (Approx.) 720 950 g
Installation to Vacuum Port No Yes —

RECOMMENDED OPERATING CONDITION / CHARACTERISTICS (at 25 °C)

Parameter Value Unit
Warm-up Heater Voltage (DC, AC) 10 ± 1 V
Heater Current (DC, AC) 1.2 A Typ.
Warm-up Time 20 s
Operation Heater Voltage (DC) 5 V
Heater Current (DC) 1 A Typ.
Discharge Starting Voltage (DC) 500 V Min.
Anode Current 1.2 A
Tube Drop Voltage (DC) 120 ± 10 V
Output Stability Drift (Max.) ±1.0 %/h
Fluctuation (Max.) 0.5 % p-p
Water Flow Rate 1.5 L/min
Estimated Life 300 h

NOTE: ATypes L1314 and L1835 cannot be operated without cooling water passing Flow of cooling water through them. Care should be taken that

PDF page 1 diagram

the lamp is positioned properly so that the two nozzles are aligned vertically, with the water flowing into the jacket at the bottom nozzle and leaving the jacket at the top nozzle. If this arrangement is not observed, there is a danger of

TLSOC0016EC

damaging the lamp due to overheating.

PDF page 1 diagram

Figure 1: Spectral Distribution L1314: UV range

PDF page 1 diagram

WAVELENGTH (nm)

L1835: Vacuum UV range

PDF page 1 diagram

WAVELENGTH (nm)

Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2006 Hamamatsu Photonics K.K.

Page 2

WATER-COOLED TYPE DEUTERIUM LAMPS L1314, L1835

Figure 2: Dimensional Outline

PDF page 2 diagram

\* L1314 cannot be used with the vacuum chamber. The main body might be damaged when using it by mistake.

OPTION (sold separately)

G POWER SUPPLY C3150

The C3150 power supply is specifically designed for water-cooled 150

PDF page 2 diagram

CATHODE

IC

1 4 2 3 ANODE HEATER

PIN CONNECTION ( Connector : Miyama Elec . MC-032 )

TLSOA0028EC

Filament (heater) output

PDF page 2 diagram
Parameter Description/Value
Output Current (DC) 1.2 A
Output Voltage Normal Operation (DC) 120 V ± 25 V
No Load (DC) 250 V Typ.
Trigger Voltage 600 V peek
Output Fluctuation Input Fluctuation (±10 %) ±0.1 % Max.
Load Fluctuation (normal operation range ) ±0.1 % Max.
Drift ±0.1 %/h Max.
Ripple 0.1 % p-p Max.
Over-load Protection 1.5 A Fuse

G VACUUM FLANGE E3444 SERIES (for L1835)

Since the L1835 vacuum UV deuterium lamp is often used while installed onto a vacuum chamber, Hamamatsu provides the E3444 series vacuum flanges specially designed for this purpose. Among these, the E3444-02 has a flange conforming to ICF114 specifications, allowing easy installation onto most vacuum chamber ports. The E3444 series also includes a general-purpose "N" flange and JIS (Japanese Industrial Standards) specification flange. Select the desired type depending on the vacuum equipment to be used.

SPECIFICATIONS

Type No. Sealing Method Flange Mount Flange Sealing Force Retention
E3444 E3444-01 E3444-02 O-Ring Regular JIS VF50 — JIS VG50 1.33 × 10-4 Pa L/s or less (1 × 10-6 Torr L/s)
ICF114 ICF114
Parameter Description/Value
Output Voltage for Warm-up (DC) 10 V, 1.2 A
Warm-up Time Approx. 30 s
Output Voltage for Operation (DC) 5 V ± 0.5 V, 1.0 A
Input Fluctuation (±10 %) ±1.0 % or less
Over-load Protection 2 A slow-blow or by electronic circuit
Input Source Voltage (AC) 100 V / 118 V / 230 V (±10 %)
Apparent Power Approx. 330 VA
Operating Ambient temperature 0 °C to 40 °C
Performance Guaranteed Temperature +5 °C to +35 °C
Cooling Method Forced air cooling
Cooling Water Detection Method Flow rate switch (1.5 L/min)
Protective Functions (LED on when malfunction) Less cooling water, excessive temperature in the C3150, short circuit, disconnection
External Dimensions (mm) 215(W) × 125(H) × 265(D)
Weight Approx. 10 kg

Dimensional Outline E3444-02 (Unit: mm)

PDF page 2 diagram
PDF page 2 diagram

TLSOA0053EA

Attachment Reference

It is designed to be simply inserted over the lamp housing.

VACUUM FLANGE

TLSOC0017EB

WEB SITE www.hamamatsu.com

HAMAMATSU PHOTONICS K.K., Electron Tube Division 314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: infos@hamamatsu.fr

United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: info@hamamatsu.co.uk North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: info@hamamatsu.se

TLSO1012E03

Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: info@hamamatsu.it

JUL. 2006 IP