i.MX 8M Nano Application Processor Datasheet
Document overview
- Manufacturer or author: NXP Semiconductors
- PDF pages: 117
Technical content
Data Sheet: Technical Data Document Number: IMX8MNCEC Rev. 5, 09/2022
Ordering Information
NXP reserves the right to change the production detail specifications as may be required to permit improvements in the design of its products. © 2019-2022 NXP Semiconductors All rights reserved. MIMX8MN6DVTJZAA MIMX8MN6DVTJZCA MIMX8MN6DVTJZDA MIMX8MN5DVTJZAA MIMX8MN4DVTJZAA MIMX8MN3DVTJZAA MIMX8MN2DVTJZAA MIMX8MN1DVTJZAA MIMX8MN5DVPIZCA MIMX8MN5DVPIZDA MIMX8MN5DVPIZAA MIMX8MN3DVPIZAA MIMX8MN1DVPIZAA
Package Information
FCBGA 14 x 14 mm, 0.5 mm pitch FCBGA 11 x 11 mm, 0.5 mm pitch 1 i.MX 8M Nano introduction The i.MX 8M Nano applicat ion processor represents NXP’s latest graphics and audio experience combining state-of-the-art media- specific features with high-performance processing while optimized for lowest power consumption. The i.MX 8M Nano family of processors features advanced implementation of a quad Arm ® Cor- tex®-A53 core, which operate s at speeds of up to 1.5 GHz. A general purpose Cortex®-M7 running up to
750 MHz core processor is for real-time and low-power
processing. The i.MX 8M Nano family of processors provides addi- tional computing resources and peripherals:
- Advanced security modules for secure boot, cipher acceleration and DRM support
- A wide range of audio interfaces, including I2S, AC 97, TDM, and S/PDIF
- Large set of peripheral s that are commonly used in consumer/industrial market, including USB and Ethernet i.MX 8M Nano Applications Processor Datasheet for Consumer Products 2.1. Recommended connections for unused input/output
2 NXP Semiconductors
Table 1. Features
- 32 KB L1 Instruction Cache 32 KB L1 Data Cache Media Processing Engine (MPE) with Arm ® NEONTM technology supporting the Advanced Single Instruction Multiple Data architecture: Floating Point Unit (FPU) with support of the Arm ® VFPv4-D16 architecture Support of 64-bit Arm®v8-A architecture
512 KB unified L2 cache
ports support 49.152 MHz BCLK. sample rate and 1/16 to 8x sample rate conversion ratio. Table 1. Features (continued)
4 NXP Semiconductors
The actual feature set depends on the part numbers as described in Table 3. interfaces, may not be enabled for specific part numbers.
1.1 Block diagram
Figure 1 shows the functional modules in the i.MX 8M Nano applications processor system. Figure 1. i.MX 8M Nano system block diagram
1 GB Ethernet
32 KB Secure RAM
32 KB I-cache 32 KB D-cache
512 KB L2 Cache
256 KB TCM
512 KB OCRAM
6 NXP Semiconductors
derivatives. See Table 2 for exceptions.
1.2 Ordering information
have questions about available parts, contact your NXP representative. Table 2. Modules supported Table 3. Orderable part numbers
1.5 GHz Consumer 0 to 95 14 x 14 mm,
Contact an NXP representative for additional details.
1.4 GHz Consumer 0 to 95 11 x 11 mm,
ready-to-use final product. It is hereby notified that a license for such use is required from Dolby Laboratories.
8 NXP Semiconductors
Figure 2. Part number nomenclature—i.MX 8M Nano family of processors
2 Modules list
describes these modules in alphabetical order. Table 4. i.MX 8M Nano modules list DMA controller used for GPMI2 operation. used as a customer microcontroller. Institute of Standards and Technology (NIST). Nano processors, the secure memory provided is 32 KB. system, and also for the system power management. comprehensive security policy within the i.MX 8M Nano platform. The DAP also provides debugger access to JTAG scan chains. chip selects to support multiple peripherals.
10 NXP Semiconductors
switched power domain when powering on/off the domain. module supports up to 32 bits of I/O. supports separate DMA channels for each NAND device. interrupts at regular intervals with minimal processor intervention. an external clock or on an internal clock. interactive graphics applications on displays. Table 4. i.MX 8M Nano modules list (continued)
which operates up to a maximum bit rate of 1.5 Gbps. operating up to a maximum bit rate of 1.5 Gbps. 512 KB multimedia RAM through a 64-bit AXI bus. PDM Pulse Density Modulation The PDM supports up to 8-channels (4 lanes). such as I2S, AC97, TDM, and codec/DSP interfaces.
12 NXP Semiconductors
processors uses JTAG port for system debugging. security modes for protecting against unauthorized accesses. Modes are selected through eFUSE configuration. path to the DRAM controller.
2.1 Recommended connections for unused input/output
to reduce overall board power. Table 5 shows the recommended connections for 14 x 14 mm package unused power supply rails. All the MMC/SD/SDIO controller IPs are based on the uSDHC IP. SD/SDIO standard, up to version 3.0. MMC standard, up to version 5.1. 1.8 V and 3.3 V operation, but do not support 1.2 V operation. 1-bit/4-bit SD and SDIO mo des, 1-bit/4-bit/8-bit MMC mode. other controller (SD2) can only support up to a 4-bit interface. USB 2.0 1x USB 2.0 controller and PHY One U SB controller and PHY that support USB 2.0. point evokes an external event on the WDOG line. Table 5. Recommended connections for 14 x 14 mm package unused power supply rails
14 NXP Semiconductors
Table 6 shows the recommended connections for 11 x 11 mm package unused power supply rails. Table 7 shows recommended connections for 14 x 14 mm package unused signal contacts/interfaces. Table 8 shows recommended connections for 11 x 11 mm package unused signal contacts/interfaces. Table 6. Recommended connections for 11 x 11 mm package unused power supply rails Table 7. Recommended connections for 14 x 14 mm package unused signal contacts/interfaces Table 8. Recommended connections for 11 x 11 mm package unused signal contacts/interfaces
Electrical characteristics
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 15
3 Electrical characteristics
This section provides the device and module-level electrical characteristics for the i.MX 8M Nano family of processors.
3.1 Chip-level conditions
This section provides the device-level electrical characteristics for the IC. See Table 9 for a quick reference to the individual tables and sections.
3.1.1 Absolute maximum ratings
Stresses beyond those listed under Table 10 may affect reliability or cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions beyond those indicated in the operating ranges or parameters tables is not implied. Table 9. i.MX 8M Nano chip-level conditions Table 10. Absolute maximum ratings for 14 x 14 mm package
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
16 NXP Semiconductors
GPIO supply voltage NVCC_JTAG, NVCC_GPIO1, NVCC_ENET, NVCC_SD1, NVCC_SD2, NVCC_NAND, NVCC_SAI2, NVCC_SAI3, NVCC_SAI5, NVCC_ECSPI, NVCC_I2C, NVCC_UART, NVCC_CLK -0.3 3.8 V — GPIO pre-driver supply voltage PVCC0_1P8, PVCC1_1P8, PVCC2_1P8 -0.3 2.15 V — Isolated core supply voltage VDD_ANA_0P8 -0.3 1.15 V — Analog core supply voltage VDD_ANA0_1P8 -0.3 2.15 V — VDD_ANA1_1P8 -0.3 2.15 V — Arm PLL supply voltage VDD_ARM_PLL_0P8 -0.3 1.15 V — VDD_ARM_PLL_1P8 -0.3 2.15 V — MIPI PHY supply voltage VDD_MIPI_0P8 -0.3 1.15 V — VDD_MIPI_1P2 -0.3 1.45 V — VDD_MIPI_1P8 -0.3 2.15 V — USB PHY supply voltage VDD_USB_0P8 -0.3 1.15 V — VDD_USB_1P8 -0.3 2.15 V — VDD_USB_3P3 -0.3 3.95 V — USB_VBUS input detected USB1_VBUS -0.3 3.95 V — XTAL supply voltage VDD_24M_XTAL_1P8 -0.3 2.15 V — Storage temperature range T STORAGE -40 150 oC— Table 11. Absolute maximum ratings for 11 x 11 mm package Table 10. Absolute maximum ratings for 14 x 14 mm package (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 17 VDD_SNVS supply voltage VDD_SNVS_0V8 -0.3 0.95 V — GPIO supply voltage NVCC_ENET_GPIO_S AI2, NVCC_I2C_UART, NVCC_SAI3_SAI5, NVCC_SD1_NAND, NVCC_ECSPI, NVCC_SD2 -0.3 3.8 V — GPIO supply voltage NVCC_CLK_JTAG_PV CC_1P8 -0.3 2.15 V — XTAL, Analog core, MIPI PHY and USB PHY 1.8 V supply voltage VDD_ANA1_XTAL_MIP I_USB_1P8 -0.3 2.15 V — Analog core and ARM PLL 1.8 V supply voltage VDD_ANA0_ARM_PLL _1P8 -0.3 2.15 V — MIPI PHY 1.2 V supply voltage VDD_MIPI_1P2 -0.3 1.45 V — USB PHY 3.3 V supply voltage VDD_USB_3P3 -0.3 3.95 V — USB_VBUS input detected USB1_VBUS -0.3 3.95 V — XTAL supply voltage VDD_24M_XTAL_1P8 -0.3 2.15 V — Storage temperature range T STORAGE -40 150 oC— Table 12. Electrostatic discharge and latch up ratings Table 11. Absolute maximum ratings for 11 x 11 mm package (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
18 NXP Semiconductors
3.1.2 Thermal resistance
3.1.2.1 14 x 14 mm FCBGA pa ckage thermal resistance Table 13 displays the 14 x 14 mm FCBGA package thermal resistance data. 3.1.2.2 11 x 11 mm FCBGA pa ckage thermal resistance Table 14 displays the 11 x 11 mm FCBGA package thermal resistance data. Table 13. 14 x 14 mm package thermal resistance data 2 Per SEMI G38-87 and JESD51-2a methodology on JESD51-9 horizontal board. 4 Thermal resistance between the die and the case (top surface) using cold plate method (MIL SPEC-883 Method 1012.1). Table 14. 11 x 11 mm thermal resistance data temperature, ambient temperature, air flow, power dissipation of other components in the board, and board thermal resistance. 2 Per SEMI G38-87 and JESD51-2a methodology on JESD51-9 horizontal board. per JEDEC JESD51-2a. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. 4 Thermal resistance between the die and the case (top surface) using cold plate method (MIL SPEC-883 Method 1012.1).
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 19
3.1.3 Operating ranges
Table 15 provides the operating ranges of the i.MX 8M Nano applications processor. For details on the chip's power structure, see the “Power Management Unit (PMU)” chapter of the i.MX 8M Nano 5 Thermal resistance data in this report is solely for a thermal performance comparison of one package to another in a standard specified environment. It is not meant to predict the performance of a package in an application-specific environment. Table 15. Operating ranges for 14 x 14 mm package
600 MHz
400 MHz
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
20 NXP Semiconductors
NVCC_DRAM 1.283 1.35 1.425 V DDR3L 1.14 1.2 1.26 V DDR4 1.06 1.1 1.14 V LPDDR4 DRAM_VREF 0.49 x NVCC_DRAM 0.5 x NVCC_DRAM 0.51 x NVCC_DRAM V Internal output, no connection is needed. VDD_DRAM_PLL_0P8 0.805 0.850 0.900 V Powe r supply for DRAM PLL, nominal mode 0.900 0.950 1.000 V Power supply for DRAM PLL, overdrive mode VDD_ANA0_1P8 VDD_ANA1_1P8 1.71 1.8 1.89 V Analog 1.8 V core power VDD_ANA_0P8 0.805 0.850 0.900 V Supplies for Analog PLL, nominal mode 0.900 0.950 1.000 V Supplies for Analog PLL, overdrive mode VDD_ARM_PLL_0P8 0.805 0.850 0.900 V Power supply for Arm PLL, nominal mode 0.900 0.950 1.000 V Power supply for Arm PLL, overdrive mode VDD_ARM_PLL_1P8 1.71 1.8 1.89 V Arm PLL 1.8 V power VDD_24M_XTAL_1P8 1.71 1.8 1.89 V XTAL 1.8 V power VDD_DRAM_PLL_1P8 1.71 1.8 1.89 V Analog 1.8 V core power VDD_MIPI_0P8 0.805 0.850 0.900 V Digital supply for MIPI PHY, nominal mode 0.900 0.950 1.000 V Digital supply for MIPI PHY, overdrive mode VDD_MIPI_1P2 1.14 1.2 1.26 V 1.2 V power for analog VDD_MIPI_1P8 1.71 1.8 1.89 V 1.8 V power for PLL and analog VDD_USB_0P8 0.805 0.850 0.900 V Digital power supply from PHY’s I/O power pads, nominal mode 0.900 0.950 1.000 V Digital power supply from PHY’s I/O power pads, overdrive mode VDD_USB_1P8 1.71 1.80 1.89 V 1.8 V analog power supply VDD_USB_3P3 3.069 3.30 3.6 V 3.3 V analog power supply USB1_VBUS 1.34 — 3.60 V USB_VBUS input detect signal Table 15. Operating ranges for 14 x 14 mm package (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 21 Temperature Sensor Accuracy5 — ±3 ±5 °C Sensing temperature range 10-85°C — ±4 ±6 °C Sensing temperature range 10-95°C — ±5 ±7 °C Sensing temperature range 10-105°C TMU Sensing Temperature Range 10 — 125 °C — T J 0— + 9 5 oC See Table 13 for complete list of junction temperature capabilities. 1 Applying the maximum voltage results in maximum power consumption and heat generation. A voltage set point = (Vmin + the supply tolerance) is recommended. This results in an optimized power/speed ratio. 2 For VDD_ARM at 1.0V typical, Power-on Hours will decreased if junction temperature is increased. Please refer to i.MX 8M Nano Product Lifetime Usage (AN12983) for details. 3 VDD_DRAM, VDD_SOC, and VDD_GPU are required to be tied together and keep same or ground. 4 Booting VDD_SOC at 0.800 V ±5% is acceptable (Vmin = 0.760 V). Software is expected to program the VDD_SOC voltage to the typical value in this table prior to first DRAM memory access. 5 “EN” of TMU Enable Register (TMU_TER) is required to be always enabled for the part to operate correctly. Table 16. Operating ranges for 11 x11 mm package
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
22 NXP Semiconductors
3.1.4 External clock sources
Each i.MX 8M Nano processor has two external input system clocks: a low frequency (RTC_XTALI) and a high frequency (XTALI). The RTC_XTALI is used for low-frequency functions. It supplies the clock for wake-up circuit, power-down real time clock operation, and slow system and watch-dog counters. The clock input can only be connected to an external oscillator. RTC_XTALO should be directly connected to VDD_SNVS_0P8. The system clock input XTALI is used to generate the main system clock. It supplies the PLLs and other peripherals. The system clock input can be connected to either an external oscillator or a crystal using internal oscillator amplifier. Table 17 shows the interface frequency requirements. DRAM_VREF 0.49 x NVCC_DRAM 0.5 x NVCC_DRAM 0.51 x NVCC_DRAM V Internal output, no connection is needed. VDD_ANA1_XTAL_MIPI_U SB_1P8, VDD_ANA0_ARM_PLL_1P 1.71 1.8 1.89 V 1.8 V power for Analog core, XTAL, MIPI PLL and analog, USB analog and ARM PLL VDD_DRAM_PLL_1P8 1.71 1.8 1.89 V Analog 1.8 V core power VDD_MIPI_1P2 1.14 1.2 1.26 V 1.2 V power for analog VDD_USB_3P3 3.069 3.30 3.6 V 3.3 V analog power supply USB1_VBUS 1.34 — 3.60 V USB_VBUS input detect signal Temperature Sensor Accuracy — ±3 ±5 °C Sensing temperature range 10-85°C — ±4 ±6 °C Sensing temperature range 10-95°C — ±5 ±7 °C Sensing temperature range 10-105°C TMU Sensing Temperature Range 10 — 125 °C — T J 0— + 9 5 oC See Table 14 for complete list of junction temperature capabilities. 1 Applying the maximum voltage results in maximum power consumption and heat generation. A voltage set point = (Vmin + the supply tolerance) is recommended. This results in an optimized power/speed ratio. 2 Booting VDD_SOC at 0.800 V ±5% is acceptable (Vmin = 0.760 V). Software is expected to program the VDD_SOC voltage to the typical value in this table prior to first DRAM memory access. 3 “EN” of TMU Enable Register (TMU_TER) is required to be always enabled for the part to operate correctly. Table 17. External input clock frequency Table 16. Operating ranges for 11 x11 mm package (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 23 The typical values shown in Table 17 are required for use with NXP software to ensure precise time keeping and USB operation. For RTC_XTALI operation, an external oscillator is necessary. RTC_XTALO should be directly connected to VDD_SNVS_0P8 when using an external 32.768 kHz oscillator. NOTE There is no internal RC oscillator. Table 18 shows the external input clock for OSC32K.
3.1.5 Estimated power supply maximum currents
Power consumption is highly dependent on the application. Estimating the maximum supply currents required for power supply design is difficult because the use cases that requires maximum supply current is not a realistic use cases. The table below represents the estimated maximum current on the power supply rails and should be used as a guideline for power supply selection. The data below is based on a combination of design simulation and characterization data based on typical datasheet voltages. Actual power consumption for typical use cases are lower than values presented on the table below. 1 The required frequency stability of this clock source is application dependent. 2 Recommended nominal frequency 32.768 kHz. 3 External oscillator or a fundamental frequency crystal appropriately coupled to the internal oscillator amplifier. Table 18. External input clock for OSC32K Table 19. Estimated power supply maximum currents for 14 x 14 mm package
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
24 NXP Semiconductors
3.1.6 Power modes
The i.MX 8M Nano supports the following power modes:
- RUN Mode: All external power ra ils are on, CPU is active and running; other internal modules can be on/off based on application.
- IDLE Mode: When there is no th read running and all high-speed devices are not active, the CPU can automatically enter this mode. The CPU can be in the power-gated state but with L2 data retained, DRAM and the bus clock are reduced. Most of the internal logic is clock gated but still remains powered. The M7 core can remain running. Compared with RUN mode, all the external power rails from the PMIC remain the same, and most of the modules still remain in their state.
- SUSPEND Mode: The most efficient power saving mode where all the cloc ks are off and all the unnecessary power supplies are off. NVCC_<XXX> I max = N x C x V x (0.5 x F) Where: N—Number of IO pins supplied by the power line C—Equivalent external capacitive load V—IO voltage (0.5 x F)—Data change rate. Up to 0.5 of the clock rate (F). In this equation, I max is in Amps, C in Farads, V in Volts, and F in Hertz. NVCC_DRAM DRAM_VFEF 10 mA
Table 20. Estimated power supply maximum currents for 11 x 11 mm package Table 19. Estimated power supply maximum currents for 14 x 14 mm package (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 25
- SNVS Mode: This mode is also called RTC mode . Only the power for the SNVS domain remains on to keep RTC and SNVS logic alive.
- OFF Mode: All power rails are off.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
26 NXP Semiconductors
Table 21 summaries the power supply states in all the power modes. Table 21. Chip power in different LP mode for 14 x 14 mm package measurement application note for more details. 2 Sum of the listed supply rails. suspend mode sets VDD_SOC/GPU/DRAM at 0.75 V.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 27 Table 22. Chip power in different LP mode for 11 x 11 mm package measurement application note for more details. mode sets VDD_SOC at 0.75 V.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
28 NXP Semiconductors
Table 23 and Table 25 summary the power supply states in all the power modes. Table 23. The power supply states for 14 x 14 mm package (VDD_SOC/GPU/DRAM at 0.75 V).
2 See Table 24
Table 24. Group name
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 29
3.2 Power supplies requir ements and restrictions
The system design must comply with power-up sequence, power-down sequence, and steady state guidelines as described in this section to guarantee the reliable operation of the device. Any deviation from these sequences may result in the following situations:
- Excessive current during power-up phase
- Prevention of the device from booting
- Irreversible damage to the pr ocessor (worst-case scenario)
Table 25. The power supply states for 11 x 11 mm package
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
30 NXP Semiconductors
3.2.1 Power-up sequence
Figure 3 illustrates the power-up sequence for 14 x 14 mm package of i.MX 8M Nano applications processor. Figure 3. The power-up sequence for 14 x 14 mm package Table 26 represents the timing parameters of the power-up sequence for 14 x 14 mm package. Table 26. Power-up sequence for 14 x 14 mm package
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 31 T3 Delay from RTC_RESET_B de-as sert to stable 32 k existed — 40 100 s T4 Delay from PMIC_ON_REQ assert to analog 0.8 V on 0 0.2 — ms T5 Delay from analog 0.8 V on to analog 0.8/0/9 V on 0 2 — ms T6 Delay from analog 0.8/0.9 V on to PHY 0.9 V on 0 15 — s T7 Delay from PHY 0.9 V on to VDD_ARM on 0 2 — ms T8 Delay from VDD_ARM on to analog 1.8 V on 0 15 — s T9 Delay from analog 1.8 V on to digital 1.8 V on 0 2 — ms T10 Delay from digital 1.8 V on to NVCC_DRAM on 0 2 — ms T11 Delay from NVCC_DRAM on to digital 2.5 V and 3.3 V on 0 2 — ms T12 Delay from digital 2.5 V and 3.3 V on to PHY 1.2 V on 0 2 — ms T131 Delay from digital 2.5 V and 3.3 V on to POR_B de-assert 0 20 — ms t1 Uncertain period before PMIC_ON_RE Q assert during VDD_SNVS_0P8 ramp up. For ramp up requirement, only VDD_ANA0_1P8 has 5 s minimum requirement, others do not have such requirement. During power-up, make sure NVCC_xxx - PVCCx_1P8 < 2 V. 1 The values of T13 depend on T2. RTC_RESET_B must be de-assert before POR_B de-asserts. Table 26. Power-up sequence for 14 x 14 mm package (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
32 NXP Semiconductors
Figure 4 illustrates the power-up sequence for 11 x 11 mm package of i.MX 8M Nano applications processor. Figure 4. The power-up sequence for 11 x 11 mm package up before POR_B release or after POR_B release. Table 27 represents the timing parameters of the power-up sequence for 11 x 11 mm package. Table 27. Power-up sequence for 11 x 11 mm package
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 33
3.2.2 Power-down sequence
Figure 5 illustrates the power-down sequence for 14 x 14 mm package of i.MX 8M Nano applications processor. Figure 5. The power-down sequence for 14 x 14 mm package1 t1 Uncertain period before PMIC_ON_RE Q assert during VDD_SNVS_0P8 ramp up. 1 The values of T10 depend on T2. RTC_RESET_B must be de-assert before POR_B de-asserts.
- VDD_MIPI_1P2 should be powered down before VDD_MIPI_1P8, no other strict requirement with other power rails.
Table 27. Power-up sequence for 11 x 11 mm package (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
34 NXP Semiconductors
Table 28 represents the timing parameters of the power-down sequence for 14 x 14 mm package. Figure 6 illustrates the power-down sequence for 11 x 11 mm package of i.MX 8M Nano applications processor. Figure 6. The power-down sequence for 11 x 11 mm package1 Table 28. Power-down sequence for 14 x 14 mm package During power-down, make sure NVCC_xxx - PVCCx_1P8 < 2 V.
- VDD_MIPI_1P2 should be powered down before VDD_MIPI_1P8, no other strict requirement with other power rails.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 35 Table 29 represents the timing parameters of the power-down sequence for 11 x 11 mm package.
3.3 PLL electrical characteristics
Table 30 shows PLL electrical characteristics. Table 29. Power-down sequence for 11 x 11 mm package Table 30. PLL electrical parameters
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
36 NXP Semiconductors
3.4 On-chip oscillators
3.4.1 OSC24M
A 24 MHz oscillator is used as the primary clock source for the PLLs to generate the clock for the CPU, BUS, and high-speed interfaces. For fractional PLLs, the 24 MHz clock from the oscillator can be used as the PLL reference clock directly. SYS_PLL3 Clock output range 600 MHz — 1 GHz Reference clock 24 MHz Lock time 50 s ARM_PLL Clock output range 800 MHz — 2 GHz Reference clock 24 MHz Lock time 50 s M7_ALT_PLL Clock output range 400 MHz — 800 MHz Reference clock 24 MHz Lock time 50 s DRAM_PLL Clock output range 400 MHz — 800 MHz Reference clock 24 MHz Lock time 500 s GPU_PLL Clock output range 800 MHz — 1600 MHz Reference clock 24 MHz Lock time 50 s 1 Lock time is referring from PLL enable to valid lock flag time. Table 31. Crystal specifications1 1 Actual working drive level is depend on real design. Please contact crystal vendor for selecting drive level of crystal. Table 30. PLL electrical parameters (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 37
3.4.2 OSC32K
This block implements an amplifier that when combined with a suitable quartz crystal and external load capacitors implements a low power oscillator. Figure 7. Crystal model and external components
3.5 General purpose I/O (GPIO) DC parameters
operating ranges in Table 15, unless otherwise noted. Table 32. 32K crystal specifications 2 Actual working drive level is depend on real design. Please contact crystal vendor for selecting drive level of crystal. 3 ESR is the equivalent series resistance of the crystal. 4 Rf is the feedback resistor to bias the amplifier. A larger value of Rf is preferred at lower frequencies. 5 Rs is the series resistor to limit amplifier gain and reduce power dissipation in the crystal.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
38 NXP Semiconductors
3.5.1 DDR I/O DC electrical characteristics
The DDR I/O pads support LPDDR 4, DDR4, and DDR3L operational modes. The DDR Memory Controller (DDRMC) is designed to be compatible with JEDEC-compliant SDRAMs. DDRMC operation is contingent upon the board’s DDR design adherence to the DDR design and layout requirements stated in the hardware development guide for the i.MX 8M Nano applications processor. Table 33. GPIO DC parameters Table 34. Additional leakage parameters
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 39
3.6 I/O AC parameters
This section includes the AC parameters of the following I/O types:
- General Purpose I/O (GPIO) The GPIO load circuit and output transition time waveforms are shown in Figure 8 and Figure 9.
Figure 8. Load circuit for output Figure 9. Output transition time waveform
3.6.1 General purpose I/O AC parameters
behavior is determined by the appropriate control bits in the IOMUXC control registers. Table 35. Maximum frequency of operation for input Table 36. Maximum frequency of operation for output
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
40 NXP Semiconductors
3.7 Output buffer impedance parameters
This section defines the I/O impedance parameters of the i.MX 8M Nano family of processors for the following I/O types: NOTE DDR I/O output driver impedance is measured with “long” transmission line of impedance Ztl attached to I/O pad and incident wave launched into transmission line. Rpu/Rpd and Ztl form a voltage divider that defines specific voltage of incident wave relative to OVDD. Output driver impedance is calculated from this voltage divider (see Figure 10). 11X 0X 6x Slow Slew 250 130 200 100 11X 1X 6x Fast Slew 250 130 200 100 Table 36. Maximum frequency of operation for output (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 41 Figure 10. Impedance matching load for measurement
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
42 NXP Semiconductors
3.7.1 DDR I/O output buffer impedance
Table 37 shows DDR I/O output buffer impedance of i.MX 8M Nano family of processors. Note: 1. Output driver impedance is controlled across PVTs using ZQ calibration procedure. 2. Calibration is done against 240 external reference resistor. 3. Output driver impedance deviation (calibration accuracy) is ±5% (max/min impedance) across PVTs.
3.8 System modules timing
This section contains the timing and electrical parameters for the modules in each i.MX 8M Nano processor.
3.8.1 Reset timings parameters
Figure 11 shows the reset timing and Table 38 lists the timing parameters. Figure 11. Reset timing diagram Table 37. DDR I/O output buffer impedance Table 38. Reset timing parameters
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 43
3.8.2 WDOG Reset timing parameters
Figure 12 shows the WDOG reset timing and Table 39 lists the timing parameters. Figure 12. WDOGx_B timing diagram Manual (IMX8MNRM) for detailed information.
3.9 External peripheral interface parameters
The following subsections provide information on external peripheral interfaces.
3.9.1 ECSPI timing parameters
parameters for master and slave modes. Table 39. WDOGx_B timing parameters
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
44 NXP Semiconductors
3.9.1.1 ECSPI Master mode timing
Figure 13 depicts the timing of ECSPI in master mode. Table 40 lists the ECSPI master mode timing characteristics. Figure 13. ECSPI Master mode timing diagram Table 40. ECSPI Master mode timing parameters 1 See specific I/O AC parameters Section 3.6, I/O AC parameters”. 2 SPI_RDY is sampled internally by ipg_clk and is asynchronous to all other CSPI signals.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 45
3.9.1.2 ECSPI Slave mode timing
Figure 14 depicts the timing of ECSPI in Slave mode. Table 41 lists the ECSPI Slave mode timing characteristics. Figure 14. ECSPI Slave mode timing diagram Table 41. ECSPI Slave mode timing parameters
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
46 NXP Semiconductors
3.9.2 Ultra-high-speed SD/SDIO/MMC host interface (uSDHC) AC
This section describes the electrical information of the uSDHC, which includes SD/eMMC 5.1 (single data rate) timing, eMMC 5.1/SD3.0 (dual data rate) AC timing, and SDR50/SDR104 AC timing. 3.9.2.1 SD/eMMC5.1 (single data rate) AC timing Figure 15 depicts the timing of SD3.0/eMMC5.1 (SDR), and Table 42 lists the SD3.0/eMMC5.1 (SDR) timing characteristics. Figure 15. SD3.0/eMMC5.1 (SDR) timing Table 42. SD3.0/eMMC5.1 (SDR) interface timing specification
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
48 NXP Semiconductors
3.9.2.3 HS400 DDR AC timing
Figure 17 depicts the timing of HS400 mode, and Table 44 lists the HS400 timing characteristics. Be aware that only data is sampled on both edges of the clock (not applicable to CMD). The CMD input/output timing for HS400 mode is the same as CMD input/output timing for SDR104 mode. Check SD5, SD6, and SD7 parameters in Table 46 SDR50/SDR104 Interface Timing Specification for CMD input/output timing for HS400 mode. Figure 17. HS400 Mode timing Table 44. HS400 interface timing specification Table 43. eMMC5.1/SD3.0 (DDR) interface timing specification (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 49
3.9.2.4 HS200 Mode AC timing
Figure 18 depicts the timing of HS200 mode, and Table 45 lists the HS200 timing characteristics. Figure 18. HS200 timing Table 45. HS200 interface timing specification 1 HS200 is for 8 bits while SDR104 is for 4 bits. Table 44. HS400 interface timing specification (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
50 NXP Semiconductors
3.9.2.5 SDR50/SDR104 AC timing
Figure 19 depicts the timing of SDR50/SDR104, and Table 46 lists the SDR50/SDR104 timing characteristics. Figure 19. SDR50/SDR104 timing Table 33, "GPIO DC parameters," on page 38. Table 46. SDR50/SDR104 interface timing specification 1 Data window in SDR100 mode is variable.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 51
3.9.3 Ethernet controller (ENET) AC electrical specifications
The following timing specs are defined at the chip I/O pin and must be translated appropriately to arrive at timing specs/constraints for the physical interface. Table 47. ENET signal mapping for PHY, and MAC also use this 50M clock. MAC use external 50M clock. TX_ER when configured in the ALT1 mode. TXC when configured in the ALT0 mode. RX_ER when configured in the ALT1 mode. RXC when configured in the ALT0 mode.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
52 NXP Semiconductors
GPIO1_IO08 1588_EVENT0_ IN RMII/RGMII ALT1 I Capture/compar e block input/output event bus signal. When configured for capture and a rising edge is detected, the current timer value is latched and transferred into the corresponding ENET_TCCRn register for inspection by software. When configured for compare, the corresponding signal 1588_EVENT is asserted for one cycle when the timer reaches the compare value programmed in register ENET_TCCRn. An interrupt or DMA request can be triggered if the corresponding bit in ENET_TCSRn[TIE] or ENET_TSCRn[TDRE] is set. GPIO1_IO09 1588_EVENT0_ OUT RMII/RGMII ALT1 O — I2C2_SCL 1588_EVENT1_ IN RMII/RGMII ALT1 I — I2C2_SDA 1588_EVENT1_ OUT RMII/RGMII ALT1 O — GPIO1_IO00 ENET_PHY_RE F_CLK_ROOT RGMII ALT1 O Reference clock for PHY. SD1_CLK MDC RMII ALT1 O — SD1_CMD MDIO RMII ALT1 I/O — SD1_DATA0 TX_D1 RMII ALT1 O — SD1_DATA1 TX_D0 RMII ALT1 O — SD1_DATA2 RX_D0 RMII ALT1 I — SD1_DATA3 RX_D1 RMII ALT1 I — SD1_DATA4 TX_EN RMII ALT1 O — SD1_DATA5 TX_ER RMII ALT1 O For RM II—SD1_DATA5 functions as RMII TX_ER when configured in the ALT1 mode. SD1_DATA6 RX_EN (CRS_DV) RMII ALT1 I — SD1_DATA7 RX_ER RMII ALT1 I For RM II—SD1_DATA7 functions as RMII RX_ER when configured in the ALT1 mode. SD1_RESET_B REF_CLK RMII A LT1 O For RMII—SD1_RESET_B functions as RMII REF_CLK when configured in the ALT1 mode. Table 47. ENET signal mapping (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 53
3.9.3.1 RMII mode timing
Figure 20 shows RMII mode timings. Table 48 describes the timing parameters (M16–M21) shown in the figure. Figure 20. RMII mode signal timing diagram
3.9.3.2 RGMII signal switching specifications
Table 48. RMII signal timing
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
54 NXP Semiconductors
Figure 21. RGMII transmit signal timing diagram original Figure 22. RGMII receive signal timing diagram original Table 49. RGMII signal switching specifications1
1 The timings assume the following configuration:
2 For 10 Mbps and 100 Mbps, Tcyc will scale to 400 ns ±40 ns and 40 ns ±4 ns respectively.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 55 Figure 23. RGMII receive signal timing diagram with internal delay
3.9.4 General-purpose media interface (GPMI) timing
up to 200 MB/s I/O speed and individual chip select. separately, as described in the following subsections. Asynchronous mode. Table 50 describes the timing parameters (NF1–NF17) that are shown in the figures. Figure 24. Command Latch cycle timing diagram
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
56 NXP Semiconductors
Figure 25. Address Latch cycle timing diagram Figure 26. Write Data Latch cycle timing diagram Figure 27. Read Data Latch cycle timing diagram (Non-EDO Mode) Figure 28. Read Data Latch cycle timing diagram (EDO mode)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 57 In EDO mode (Figure 27), NF16/NF17 are different from the definition in non-EDO mode (Figure 26). They are called tREA/tRHOH (RE# access time/RE# HIGH to output hold). The typical values for them are 16 ns (max for tREA)/15 ns (min for tRHOH) at 50 MB/s EDO mode. In EDO mode, GPMI samples NAND_DATAxx at the rising edge of delayed NAND_RE_B provided by an internal DPLL. The delay value can be controlled by GPMI_CTRL1.RDN_DELAY (see the GPMI chapter of the i.MX 8M Nano 0x8 at 50 MT/s EDO mode. But if the board delay is big enough and cannot be ignored, the delay value should be made larger to compensate the board delay. Table 50. Asynchronous mode timing parameters1
1 GPMI’s Asynchronous mode output timing can be controlled by the module’s internal registers
HW_GPMI_TIMING0_ADDRESS_SETUP, HW_GPMI_TIMING0_DATA_SETUP, and HW_GPMI_TIMING0_DATA_HOLD. This AC timing depends on these registers settings. In the table, AS/DS/DH represents each of these settings. 2 AS minimum value can be 0, while DS/DH minimum value is 1. 3 T = GPMI clock period -0.075 ns (half of maximum p-p jitter). 4 NF12 is guaranteed by the design.
6 EDO mode, GPMI clock 100 MHz
(AS=DS=DH=1, GPMI_CTL1 [RDN_DELAY] = 8, GPMI_CTL1 [HALF_PERIOD] = 0).
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
58 NXP Semiconductors
3.9.4.2 Source synchronous mode AC timing (ONFI 2.x compatible) Figure 29 to Figure 31 show the write and read timing of Source Synchronous mode. Figure 29. Source Synchronous mode command and address timing diagram
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
60 NXP Semiconductors
Figure 32. NAND_DQS/NAND_DQ read valid window Table 51. Source Synchronous mode timing parameters1
1 GPMI’s Source Synchronous mode output timing can be controlled by the module’s internal registers
on these registers settings. In the table, CE_DELAY/PRE_DELAY/POST_DELAY represents each of these settings. 2 T = tCK(GPMI clock period) –0.075 ns (half of maximum p-p jitter).
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 61 3.9.4.3 ONFI NV-DDR2 mode (ONFI 3.2 compatible)
3.9.4.3.1 Command and address timing
ONFI 3.2 mode command and address timing is the same as ONFI 1.0 compatible Async mode AC timing.
3.9.4.3.2 Read and write timing
mode AC Timing, for details.
3.9.4.4 Toggle mode AC Timing
3.9.4.4.1 Command and address timing
Toggle mode command and address timing is the same as ONFI 1.0 compatible Asynchronous mode AC timing. See Section 3.9.4.1, Asynchronous mode AC timing (ONFI 1.0 compatible), for details.
3.9.4.4.2 Read and write timing
Figure 33. Toggle mode data write timing
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
62 NXP Semiconductors
Figure 34. Toggle mode data read timing Table 52. Toggle mode timing parameters
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 63 For DDR Toggle mode, Figure 32 shows the timing diagram of NAND_DQS/NAND_DATAxx read valid window. The typical value of tDQSQ is 1.4 ns (max) and 1.4 ns (max) for tQHS at 133 MB/s. GPMI samples NAND_DATA[7:0] at both the rising and falling edges of a delayed NAND_DQS signal, which is provided by an internal DPLL. The delay value of this register can be controlled by the GPMI register GPMI_READ_DDR_DLL_CTRL.SLV_DLY_TARGET (see the GPMI chapter of the i.MX 8M Nano 0x7, which means a 1/4 clock cycle delay is expected. But if the board delay is big enough and cannot be ignored, the delay value should be made larger to compensate the board delay.
3.9.5 I 2C bus characteristics
The Inter-Integrated Circuit (I2C) provides functionality of a standard I2C master and slave. The I2C is designed to be compatible with the I2C Bus Specification, version 2.1, by Philips Semiconductor (now NXP Semiconductors).
3.9.6 MIPI D-PHY timing parameters
MIPI D-PHY electrical specifications are compliance. NF24 postamble delay tPOST POST_DELAY T + 0.43 [see note2] —n s NF28 Data write setup tDS 5 0.25 tCK - 0.32 — ns NF29 Data write hold tDH 5 0.25 tCK - 0.79 — ns NF30 NAND_DQS/NAND_DQ read setup skew tDQSQ 6 —3 . 1 8 n s NF31 NAND_DQS/NAND_DQ read hold skew tQHS 6 —3 . 2 7 n s 1 AS minimum value can be 0, while DS/DH minimum value is 1. 2 T = tCK (GPMI clock period) - 0.075 ns (half of maximum p-p jitter). 3 CE_DELAY represents HW_GPMI_TIMING2[CE_DELAY]. NF18 is guaranteed by the design. Read/Write operation is started with enough time of ALE/CLE assertion to low level.
4 PRE_DELAY + 1 (AS + DS)
5 Shown in Figure 33. 6 Shown in Figure 34. Table 52. Toggle mode timing parameters (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
64 NXP Semiconductors
3.9.7 PDM timing parameters
Figure 35 illustrates the input timing of the PDM. Figure 35. PDM input timing rate and CLKDIV without I/O timing concerns.
3.9.8 Pulse width modulator (PWM) timing parameters
Table 53. MIPI PHY worst power dissipation1 (at least 1 clock lane enable).
2.1 Gbps
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 65 being input to the counter. The output is available at the pulse-width modulator output (PWMO) external pin. Figure 36 depicts the timing of the PWM, and Table 54 lists the PWM timing parameters. Figure 36. PWM timing
3.9.9 FlexSPI timing parameters
Measurements are with a load of 15 pF and an input slew rate of 1 V/ns.
3.9.9.1 FlexSPI input/read timing
- Dummy read strobe genera ted by FlexSPI controller and looped back internally (FlexSPIn_MCR0[RXCLKSRC] = 0x0)
- Dummy read strobe generate d by FlexSPI controller and looped back through the DQS pad (FlexSPIn_MCR0[RXCLKSRC] = 0x1)
- Read strobe provided by memory device and input from DQS pad (FlexSPIn_MCR0[RXCLKSRC] = 0x3) The following sections describe input signal timing for each of these four internal sample clock sources.
3.9.9.1.1 SDR mode with FlexSPI n_MCR0[RXCLKSRC] = 0x0, 0x1, 0x2
Table 54. PWM output timing parameters Table 55. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x0
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
66 NXP Semiconductors
Figure 37. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x0, 0x1, 0x2 falling edge, and FlexSPI controller sampling read data on the falling edge.
3.9.9.1.2 SDR mode with FlexSPI n_MCR0[RXCLKSRC] = 0x3
- A 1 — Memory generates both read data and read strobe on SCK rising edge (or falling edge)
- A 2 — Memory generates read data on SCK falling edge and generates read strobe on SCK rising edge
Table 56. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x1, 0x2 Table 57. FlexSPI input timing in SDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case A1)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
68 NXP Semiconductors
3.9.9.1.3 DDR mode with FlexSPI n_MCR0[RXCLKSRC] = 0x0, 0x1, 0x2
Figure 40. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x0, 0x1, 0x2
3.9.9.1.4 DDR mode with FlexSPI n_MCR0[RXCLKSRC] = 0x3
Table 59. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x0 Table 60. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x1, 0x2 Table 61. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3 (Case 1)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 69 Figure 41. FlexSPI input timing in DDR mode where FlexSPIn_MCR0[RXCLKSRC] = 0x3
3.9.9.2 FlexSPI output/write timing
3.9.9.2.1 SDR mode
Figure 42. FlexSPI output timing in SDR mode Table 62. FlexSPI output timing in SDR mode FlexSPI SDR input timing specifications. Processor Reference Manual (IMX8MNRM) for more details.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
70 NXP Semiconductors
3.9.9.2.2 DDR mode
Figure 43. FlexSPI output timing in DDR mode
3.9.10 SAI/I2S switching specifications
This section provides the AC timings for the SAI in Master (clocks driven) and Slave (clocks input) modes. (SAI_BCLK) and/or the frame sync (SAI_FS) shown in the figures below. Table 63. FlexSPI output timing in DDR mode FlexSPI SDR input timing specifications. Processor Reference Manual (IMX8MNRM) for more details. Table 64. Master mode SAI timing (50 MHz)1
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 71 S4 SAI_BCLK pulse width high/low 40% 60% BCLK period S5 SAI_BCLK to SAI_FS output valid — 2 ns S6 SAI_BCLK to SAI_FS output invalid 0 — ns S7 SAI_BCLK to SAI_TXD valid — 2 ns S8 SAI_BCLK to SAI_TXD invalid 0 — ns S9 SAI_RXD/SAI_FS input setup before SAI_BCLK 2 — ns S10 SAI_RXD/SAI_FS input hold after SAI_BCLK 0 — ns 1 To achieve 50 MHz for BCLK operation, use the following configuration. For TX, configure BCI=0 in SAI TCR2 register and FSD=1 in SAI TCR4 register. For RX, configure BCI=1 in SAI TCR2 register and FSD=0 in SAI TCR4 register. Table 65. Master mode SAI timing (25 MHz) Table 64. Master mode SAI timing (50 MHz)1 (continued)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
72 NXP Semiconductors
Figure 44. SAI timing—Master modes Table 66. Slave mode SAI timing (50 MHz)1 Table 67. Slave mode SAI timing (25 MHz)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 73 Figure 45. SAI Timing — Slave Modes
3.9.11 SPDIF timing parameters
encoding, the SPDIF data signal is modulated by a clock that is twice the bit rate of the data signal. SPDIF in Rx mode and the timing of the modulating Tx clock (SPDIF_ST_CLK) for SPDIF in Tx mode. Table 68. SPDIF timing parameters
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
74 NXP Semiconductors
Figure 46. SPDIF_SR_CLK timing diagram Figure 47. SPDIF_ST_CLK timing diagram
3.9.12 UART I/O configuration and timing parameters
3.9.12.1 UART RS-232 I/O config uration in different modes
3.9.12.2 UART RS-232 Serial mode timing
This section describes the electrical information of the UART module in the RS-232 mode. Table 69. UART I/O configuration vs. mode
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 75
3.9.12.2.1 UART transmitter
Figure 48 depicts the transmit timing of UART in the RS-232 Serial mode, with 8 data bit/1 stop bit format. Table 70 lists the UART RS-232 Serial mode transmit timing characteristics. Figure 48. UART RS-232 Serial mode transmit timing diagram
3.9.12.2.2 UART receiver
Serial mode receive timing characteristics. Figure 49. UART RS-232 Serial mode receive timing diagram Table 70. RS-232 Serial mode transmit timing parameters 1 Fbaud_rate: Baud rate frequency. The maximum baud rate the UART can support is (ipg_perclk frequency)/16. 2 Tref_clk: The period of UART reference clock ref_clk (ipg_perclk after RFDIV divider). Table 71. RS-232 Serial mode receive timing parameters 2 Fbaud_rate: Baud rate frequency. The maximum baud rate the UART can support is (ipg_perclk frequency)/16.
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
76 NXP Semiconductors
3.9.13 USB PHY parameters
This section describes the USB-OTG PHY parameters.
3.9.13.1 Pad/Package/Board connections
The USB1_VBUS pin cannot directly connect to the 5 V VBUS voltage on the USB2.0 link. The USB1_VBUS pin must be isolated by an external 30 K1% precision resistor. The USB 2.0 PHY uses USB1_TXRTUNE and an external resistor to calibrate the USB1_DP/DN 45 source impedance. The external resistor value is 200 1% precision on USB1_TXRTUNE pad to ground.
3.9.13.2 USB PHY worst power consumption
Table 72 shows the USB 2.0 PHY worst power dissipation. Table 72. USB 2.0 PHY worst power dissipation
4 Boot mode configuration
4.1 Boot mode configuration pins
sampled at reset and can be used to override fuse values, depending on the value of BT_FUSE_SEL fuse.
4.2 Boot device interface allocation
which are configured during boot when appropriate. Table 73. Fuses and associated pins used for boot Table 74. Interface allocation during boot on the fuse “CS select (SPI only)“. on the fuse “CS select (SPI only)“. on the fuse “CS select (SPI only)“. 8-bit, only CS0 is supported.
78 NXP Semiconductors
Table 74. Interface allocation during boot (continued)
Package information and contact assignments i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 79
5 Package information and contact assignments
This section includes the contact assignment information and mechanical package drawing. 5.1 14 x 14 mm package information 5.1.1 14 x 14 mm, 0.5 mm pitch, ball matrix Figure 50 shows the top, bottom, and side views of the 14 × 14 mm FCBGA package.
80 NXP Semiconductors
Figure 50. 14 X 14 MM BGA, case x package top, bottom, and side views
Table 75 shows supplies contact assignments for the 14 x 14 mm package. Table 75. i.MX 8M Nano 14 x 14 mm supplies contact assignments
82 NXP Semiconductors
Table 76 shows an alpha-sorted list of functional contact assignments for the 14 x 14 mm package. Table 76. i.MX 8M Nano 14 x 14 mm functional contact assignments Table 75. i.MX 8M Nano 14 x 14 mm supplies contact assignments (continued)
Table 76. i.MX 8M Nano 14 x 14 mm functional contact assignments (continued)
84 NXP Semiconductors
86 NXP Semiconductors
88 NXP Semiconductors
90 NXP Semiconductors
Table 77 shows the i.MX 8M Nano 14 x 14 mm 0.5 mm pitch ball map.
1 During reset: output high without PU/PD; After reset: input with PU
2 Mandatory requirement: JTAG_TMS pin must be connected with a 50 ohm serial resistor near the component.
3 During reset: input without PU/PD; After reset: input with PD
Table 77. 14 x 14 mm, 0.5 mm pitch ball map
92 NXP Semiconductors
Table 77. 14 x 14 mm, 0.5 mm pitch ball map (continued)
94 NXP Semiconductors
Package information and contact assignments i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 95 5.2 11 x 11 mm package information 5.2.1 11 x 11 mm, 0.5 mm pitch, ball matrix Figure 51 shows the top, bottom, and side views of the 11 × 11 mm FCBGA package.
96 NXP Semiconductors
Figure 51. 11 X 11 MM BGA, case x package top, bottom, and side views
Table 78 shows supplies contact assignments for the 11 x 11 mm package. Table 78. i.MX 8M Nano 11 x 11 mm supplies contact assignments
98 NXP Semiconductors
Table 79 shows an alpha-sorted list of functional contact assignments for the 11 x 11 mm package. Table 79. i.MX 8M Nano 11 x 11 mm functional contact assignments
Table 79. i.MX 8M Nano 11 x 11 mm functional contact assignments (continued)
100 NXP Semiconductors
102 NXP Semiconductors
104 NXP Semiconductors
106 NXP Semiconductors
Table 80 shows the i.MX 8M Nano 11 x 11 mm 0.5 mm pitch ball map. 2 Mandatory requirement: JTAG_TMS pin must be connected with a 50 ohm serial resistor near the component.
Table 80. 11 x 11 mm, 0.5 mm pitch ball map
108 NXP Semiconductors
Table 80. 11 x 11 mm, 0.5 mm pitch ball map (continued)
110 NXP Semiconductors
5.3 DDR pin function list
Table 81 shows the DDR pin function list. Table 81. DDR pin function list
Table 81. DDR pin function list (continued)
112 NXP Semiconductors
Revision history
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 113
6 Revision history
Table 82 provides a revision history for this data sheet. Rev.number Date Substantive change(s) Rev 5 09/2022 A ddendum has been removed from the data sheet. I n Table 2, "Modules supported", updated the part numbers. In Table 3, "Orderable part numbers", updated the part numbers. In Figure 2, "Part number nomenclature—i.MX 8M Nano family of processors" updated part number. I n Table 13, "14 x 14 mm package thermal resistance data", updated the values of “Junction to Ambient Natural Convection” and “Junction to Case”. Updated Figure 50, "14 X 14 MM BGA, case x package top, bottom, and side views". Updated the footnotes in the Table 64, "Master mode SAI timing (50 MHz)" and Table 66, "Slave mode SAI timing (50 MHz)". Rev 4 05/2022 Added an Addendum to the existing data sheet. Rev. 3 04/2022 In Table 2, "Modules supported", updated the part numbers. I n Table 3, "Orderable part numbers", updated the part numbers. I n Figure 2, "Part number nomenclature—i.MX 8M Nano family of processors" updated part number. I n Table 13, "14 x 14 mm package thermal resistance data", updated the values of “Junction to Ambient Natural Convection” and “Junction to Case”. Updated Figure 50, "14 X 14 MM BGA, case x package top, bottom, and side views". Rev. 2 03/2022 Added a note in the Table 16, "Operating ranges for 11 x11 mm package" Added a footnote for the Figure 5, "The power-down sequence for 14 x 14 mm package" and Figure 6, "The power-down sequence for 11 x 11 mm package" Updated Table 13, "14 x 14 mm package thermal resistance data" and Table 14, "11 x 11 mm thermal resistance data" Updated the driver level and ESR values in the Table 31, "Crystal specifications" Updated the Section 3.4.2, OSC32K Updated the Temperature Sensor Accuracy row in Table 15, "Operating ranges for 14 x 14 mm package" and Table 16, "Operating ranges for 11 x11 mm package". I n Table 15, "Operating ranges for 14 x 14 mm package" and Table 16, "Operating ranges for 11 x11 mm package", added row TMU Sensing Temperature Range.
Rev. 1 03/2021 Added a note for the Figure 1, "i.MX 8M Nano system block diagram" and Table 2, "Modules supported" Added part numbers for 11 x 11 mm package and descriptions in the Table 3, "Orderable part numbers" Updated the package type and part differentiator in the Figure 2, "Part number nomenclature—i.MX 8M Nano family of processors" Updated the LCDIF descriptions in the Table 4, "i.MX 8M Nano modules list" Updated the Section 2.1, Recommended connections for unused input/output Updated the title and the maximum values of VDD_ARM_PLL_0P8 and VDD_USB_0P8 in the Table 10, "Absolute maximum ratings for 14 x 14 mm package" Added the Table 11, "Absolute maximum ratings for 11 x 11 mm package" Updated the title of Table 13, "14 x 14 mm package thermal resistance data" Added the new Section 3.1.2.2, 11 x 11 mm FCBGA package thermal resistance Updated the VDD_ANA_0P8, VDD_ARM_ PLL_0P8, VDD_MIPI_0P8, VDD_USB_0P8, VDD_DRAM_PLL_0P8, and USB1_VBUS in the Table 15, "Operating ranges for 14 x 14 mm package" Added the Table 16, "Operating ranges for 11 x11 mm package" Updated the title of Table 19, "Estimated power supply maximum currents for 14 x 14 mm package" Added the Table 20, "Estimated power supply maximum currents for 11 x 11 mm package" Updated and added Low-V suspend mode data in the Table 21, "Chip power in different LP mode for 14 x 14 mm package" Added the Table 22, "Chip power in different LP mode for 11 x 11 mm package" Updated and added a foot note in the Table 23, "The power supply states for 14 x 14 mm package" Added the Table 25, "The power supply states for 11 x 11 mm package" Updated POR_B and added a note for Figure 3, "The power-up sequence for 14 x 14 mm package" Updated the T13 descriptions in the Table 26, "Power-up sequence for 14 x 14 mm package" Added the Figure 4, "The power-up sequence for 11 x 11 mm package" and Table 27, "Power-up sequence for 11 x 11 mm package" Updated the titles of Figure 5, "The power-down sequence for 14 x 14 mm package" and Table 28, "Power-down sequence for 14 x 14 mm package" Added the Figure 6, "The power-down sequence for 11 x 11 mm package" and Table 29, "Power-down sequence for 11 x 11 mm package" Removed the Section, Power supplies constraints Updated the lock time and GPU values in the Table 30, "PLL electrical parameters"; added the M7_ALT_PLL in the Table 30, "PLL electrical parameters" Fixed a typo in the Table 75, "i.MX 8M Nano 14 x 14 mm supplies contact assignments" Changed the name of TSENSOR_RES_EXT in the Table 76, "i.MX 8M Nano 14 x 14 mm functional contact assignments"; updated the input/out status of GPIO1_IO07, NAND_CE0_B, and NAND_RE_B in the Table 76, "i.MX 8M Nano 14 x 14 mm functional contact assignments" Updated the names of H10, M1, and W22 in the Table 77, "14 x 14 mm, 0.5 mm pitch ball map" Added the Section 5.2, 11 x 11 mm package information Updated LPDDR4 information of DRAM_AC14 and DRAMAC34 in the Table 81, "DDR pin function list" Rev. 0.1 03/2020 Updated the Ta ble, “Power supplies constraints” Rev. 0 10/2019 Initial version Rev.number Date Substantive change(s)
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 115
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022
116 NXP Semiconductors
Information in this document is provided solely to enable system and software implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information in this document. NXP reserves the right to make changes without further notice to any products herein. NXP makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in NXP data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals” must be validated for each customer application by customer‚ customer’s technical experts. NXP does not convey any license under its patent rights nor the rights of others. NXP sells products pursuant to standard terms and conditions of sale, which can be found at the following address: nxp.com/SalesTermsandConditions While NXP has implemented advanced security features, all products may be subject to unidentified vulnerabilities. Customers are responsible for the design and operation of their applications and products to reduce the effect of these vulnerabilities on customer’s applications and products, and NXP accepts no liability for any vulnerability that is discovered. Customers should implement appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP, the NXP logo, NXP SECURE CONNECTIONS FOR A SMARTER WORLD, COOLFLUX, EMBRACE, GREENCHIP, HITAG, I2C BUS, ICODE, JCOP, LIFE VIBES, MIFARE, MIFARE CLASSIC, MIFARE DESFire, MIFARE PLUS, MIFARE FLEX, MANTIS, MIFARE ULTRALIGHT, MIFARE4MOBILE, MIGLO, NTAG, ROADLINK, SMARTLX, SMARTMX, STARPLUG, TOPFET, TRENCHMOS, UCODE, Freescale, the Freescale logo, AltiVec, C-5, CodeTEST, CodeWarrior, ColdFire, ColdFire+, C-Ware, the Energy Efficient Solutions logo, Kinetis, Layerscape, MagniV, mobileGT, PEG, PowerQUICC, Processor Expert, QorIQ, QorIQ Qonverge, Ready Play, SafeAssure, the SafeAssure logo, StarCore, StarCore, Symphony, VortiQa, Vybrid, Airfast, BeeKit, BeeStack, CoreNet, Flexis, MXC, Platform in a Package, QUICC Engine, SMARTMOS, Tower, TurboLink, UMEMS, EdgeScale, EdgeLock, eIQ, and Immersive3D are trademarks of NXP B.V. All other product or service names are the property of their respective owners. AMBA, Arm, Arm7, Arm7TDMI, Arm9, Arm11, Artisan, big.LITTLE, Cordio, CoreLink, CoreSight, Cortex, DesignStart, DynamIQ, Jazelle, Keil, Mali, Mbed, Mbed Enabled, NEON, POP, RealView, SecurCore, Socrates, Thumb, TrustZone, ULINK, ULINK2, ULINK-ME, ULINK-PLUS, ULINKpro, µVision, Versatile are trademarks or registered trademarks of Arm Limited (or its subsidiaries) in the US and/or elsewhere. The related technology may be protected by any or all of patents, copyrights, designs and trade secrets. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates.The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. © 2019-2022 NXP B.V. How to Reach Us: Home Page: nxp.com Web Support: nxp.com/support
i.MX 8M Nano Applications Processor Datasheet for Consumer Products, Rev. 5, 09/2022 NXP Semiconductors 117