IL2-X009 VISHAY

Document overview

  • PDF pages: 9

Technical content

Page 1

Optocoupler, Phototransistor Output, With Base Connection

Features

  • Current Transfer Ratio (see order information)
  • Isolation Test Voltage 5300 VRMS
  • Lead-free component
  • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC

Agency Approvals

  • UL1577, File No. E52744 System Code H or J, Double Protection
  • DIN EN 60747-5-2 (VDE0884) DIN EN 60747-5-5 pending Available with Option 1

Description

The IL1/ IL2/ IL5 are optically coupled isolated pairs employing GaAs infrared LEDs and silicon NPN phototransistor. Signal information, including a DC level, can be transmitted by the drive while maintaining a high degree of electrical isolation between input and output. The IL1/ IL2/ IL5 are especially designed for driving medium-speed logic and can be used to eliminate troublesome ground loop and noise problems These couplers can be used also to replace relays and transformers in many digital interface applications such as CRT modulation.

Absolute Maximum Ratings

Tamb = 25 °C, unless otherwise specified

PDF page 1 diagram

Order Information

Part Remarks
IL1 CTR > 20 %, DIP-6
IL2 CTR > 100 %, DIP-6
IL5 CTR > 50 %, DIP-6
IL1-X006 CTR > 20 %, DIP-6 400 mil (option 6)
IL2-X006 CTR > 100 %, DIP-6 400 mil (option 6)
IL2-X009 CTR > 100 %, SMD-6 (option 9)
IL5-X009 CTR > 50 %, SMD-6 (option 9)

For additional information on the available options refer to Option Information.

Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Rating for extended periods of the time can adversely affect reliability.

Input

Parameter Test condition Symbol Value Unit
Reverse voltage V R 6.0 V
Forward current I F 60 mA
Surge current I FSM 2.5 A
Power dissipation P diss 100 mW
Derate linearly from 25 °C 1.33 mW/°C

Document Number 83612

www.vishay.com

Rev. 1.5, 26-Oct-04

Page 2

Output

Parameter Test condition Part Symbol Value Unit
Collector-emitter breakdown voltage IL1 BV CEO 50 V
IL2 BV CEO 70 V
IL5 BV CEO 70 V
Emitter-base breakdown voltage BV EBO 7.0 V
Collector-base breakdown voltage BV CBO 70 V
Collector current I C 50 mA
t < 1.0 ms I C 400 mA
Power dissipation P diss 200 mW
Derate linearly from 25 °C 2.6 mW/°C

Coupler

Parameter Test condition Symbol Value Unit
Package power dissipation P tot 250 mW
Derate linearly from 25 °C 3.3 mW/°C
Isolation test voltage (between emitter and detector referred to standard climate 23 °/50 %RH, DIN 50014) V ISO 5300 V RMS
Creepage ≥ 7.0 mm
Clearance ≥ 7.0 mm
Comparative tracking index per DIN IEC 112/VDE 0303, part 1 175
Isolation resistance V = 500 V, T = 25 °C IO amb R IO ≥ 1012 Ω
V = 500 V, T = 100 °C IO amb R IO ≥ 1011 Ω
Storage temperature T stg - 40 to + 150 °C
Operating temperature T amb - 40 to + 100 °C
Junction temperature T j 100 °C
Soldering temperature 2.0 mm from case bottom T sld 260 °C

Electrical Characteristics

Tamb = 25 °C, unless otherwise specified Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements.

Input

Parameter Test condition Symbol Min Typ. Max Unit
Forward voltage I = 60 mA F V F 1.25 1.65 V
Breakdown voltage I = 10 µA R V BR 6.0 30 V
Reverse current V = 6.0 V R I R 0.01 10 µA
Capacitance V = 0 V, f = 1.0 MHz R C O 40 pF
Thermal resistance junction to lead R thjl 750 K/W

www.vishay.com

Document Number 83612 Rev. 1.5, 26-Oct-04

Page 3

Output

Parameter Test condition Symbol Min Typ. Max Unit
Collector-emitter capacitance V = 5.0 V, f = 1.0 MHz CE C CE 6.8 pF
Collector - base capacitance V = 5.0 V, f = 1.0 MHz CB C CB 8.5 pF
Emitter - base capacitance V = 5.0 V, f = 1.0 MHz EB C EB 11 pF
Collector-emitter leakage current V = 10 V CE I CEO 5.0 50 nA
Collector-emitter saturation voltage I = 1.0 mA, I = 20 µA CE B V CESAT 0.25 V
Base-emitter voltage V = 10 V, I = 20 µA CE B V BE 0.65 V
DC forward current gain V = 10 V, I = 20 µA CE B HFE 200 650 1800
DC forward current gain saturated V = 0.4 V, I = 20 µA CE B HFE sat 120 400 600
Thermal resistance junction to lead R thjl 500 K/W

Coupler

Parameter Test condition Symbol Min Typ. Max Unit
Capacitance (input-output) V = 0 V, f = 1.0 MHz I-O C IO 0.6 pF
Insulation resistance V = 500 V I-O R S 1014 Ω

Current Transfer Ratio

Parameter Test condition Part Symbol Min Typ. Max Unit
Current Transfer Ratio (collector-emitter saturated) I = 10 mA, V = 0.4 V F CE IL1 CTR CEsat 75 %
IL2 CTR CEsat 170 %
IL5 CTR CEsat 100 %
Current Transfer Ratio (collector-emitter) I = 10 mA, V = 10 V F CE IL1 CTR CE 20 80 300 %
IL2 CTR CE 100 200 500 %
IL5 CTR CE 50 130 400 %
Current Transfer Ratio (collector-base) I = 10 mA, V = 9.3 V F CB IL1 CTR CB 0.25 %
IL2 CTR CB 0.25 %
IL5 CTR CB 0.25 %

Switching Non-saturated

Parameter Current Delay Rise time Storage Fall time Propagation H-L Propagation L-H
Test condition V = 5.0 V, R = 75 Ω, t measured at 50 % of output CE L P
Symbol I F t D t r t S t f t PHL t PLH
Unit mA µs µs µs µs µs µs
IL1 20 0.8 1.9 0.2 1.4 0.7 1.4
IL2 4.0 1.7 2.6 0.4 2.2 1.2 2.3
IL5 10 1.7 2.6 0.4 2.2 1.1 2.5

Document Number 83612

www.vishay.com

Rev. 1.5, 26-Oct-04

Page 4

Switching Saturated

Parameter Current Delay Rise time Storage Fall time Propagation H-L Propagation L-H
Test condition V = 0.4 V, R = 1.0 kΩ, V = 5.0 V, V = 1.5 V CE L CL TH
Symbol I F t D t r t S t f t PHL t PLH
Unit mA µs µs µs µs µs µs
IL1 20 0.8 1.2 7.4 7.6 1.6 8.6
IL2 5.0 1.0 2.0 5.4 13.5 5.4 7.4
IL5 10 1.7 7.0 4.6 20 2.6 7.2

Common Mode Transient Immunity

Parameter Test condition Symbol Min Typ. Max Unit
Common mode rejection output high V = 50 V , R = 1 kΩ, CM P-P L I = 10 mA F | CM | H 5000 V/µs
Common mode rejection output low V = 50 V , R = 1 kΩ, CM P-P L I = 10 mA F | CM | L 5000 V/µs
Common mode coupling capacitance C CM 0.01 pF

Typical Characteristics (Tamb = 25 °C unless otherwise specified)

VCC=5V

PDF page 4 diagram

iil1_01

iil1_02

Figure 1. Non-saturated Switching Schematic

www.vishay.com

VCC=5V

PDF page 4 diagram

Figure 2. Saturated Switching Schematic

Document Number 83612 Rev. 1.5, 26-Oct-04

Page 5

PDF page 5 diagram

iil1_03

Figure 3. Non-saturated Switching Timing

PDF page 5 diagram

iil1_04

Figure 4. Saturated Switching Timing

PDF page 5 diagram

1 10 100

IF - Forward Current - mA

iil1_05

Figure 5. Forward Voltage vs. Forward Current

Document Number 83612 Rev. 1.5, 26-Oct-04

PDF page 5 diagram

.1

1 10 100

IF - LED Current - mA

iil1_06

Figure 6. Normalized Non-Saturated and Saturated CTR vs. LED

Current

1.5

Normalized t VCE = 10 V, CTRce(sat) V o: IF = 10 mA CE = 0.4 V ˇ
TA= 50°C
NCTR(SAT) NCTR

1.0

0.5

0.0 .1

1 10 100

IF - LED Current - mA

iil1_07

Figure 7. Normalized Non-saturated and Saturated CTR vs. LED

Current

1.5

Normalized VCE = 10 to: V, IF = 10 mA
CTRce(sat TA= 70°C ) VCE = 0.4 V
NCTR(SAT) NCTR

1.0

0.5

0.0 .1 1 10 100

IF - LED Current - mA

iil1_08

Figure 8. Normalized Non-saturated and saturated CTR vs. LED

Current

www.vishay.com

Page 6

PDF page 6 diagram

1.5

Normalized t VCE = 10 V, I CTRce(sat) V o: F = 10 mA CE = 0.4 V
TA= 100°C
NC NC TR(SAT) TR

1.0

0.5

0.0 .1

1 10 100

.1

1 10

100

IF - LED Current - mA

IF - LED Current - mA

iil1_09

iil1_12

Figure 12. Normalized CTRcb vs. LED Current and Temperature

Figure 9. Normalized Non-Saturated and Saturated CTR, TA =

100 °C vs. LED Current

PDF page 6 diagram

0 10 20 30 40 50 60

IF - LED Current - mA

iil1_13

iil1_10

Figure 10. Collector-Emitter Current vs. Temperature and LED

Current

PDF page 6 diagram

-20 0 20 40 60 80 100

TA - Ambient Temperature - °C

iil1_11

iil1_14

Figure 11. Collector-Emitter Leakage Current vs.Temp.

www.vishay.com

PDF page 6 diagram

IF - LED Current - mA

Figure 13. Collector-Base Photocurrent vs. LED Current

PDF page 6 diagram

.1

1

10

100

IF -LED Current- mA

Figure 14. Normalized Photocurrent vs. IF and Temp.

Document Number 83612 Rev. 1.5, 26-Oct-04

Page 7

PDF page 7 diagram

Ib - Base Current - µA

iil1_15

Figure 15. Normalized Non-saturated HFE vs. Base Current and

Temperature

PDF page 7 diagram

1.5

1.0

0.5

0.0 1

10

100 1000

IB - Base Current - (µA)

iil1_16

Figure 16. Normalized Saturated HFE vs. Base Current and

Temperature

PDF page 7 diagram

.1

1 10 100

RL - Collector Load Resistor - kΩ

iil1_17

Figure 17. Propagation Delay vs. Collector Load Resistor

Document Number 83612

www.vishay.com

Rev. 1.5, 26-Oct-04

Page 8

Package Dimensions in Inches (mm)

PDF page 8 diagram
PDF page 8 diagram
3 2 (6.30) (6.50) 1 6 8.50)
4 5 .335 (
PDF page 8 diagram
PDF page 8 diagram

www.vishay.com

Document Number 83612 Rev. 1.5, 26-Oct-04

Page 9

Ozone Depleting Substances Policy Statement

It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operatingsystems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an

earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances.

We reserve the right to make changes to improve technical design

and may do so without further notice.

Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use.

Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423

Document Number 83612

www.vishay.com

Rev. 1.5, 26-Oct-04