HR30 HIROSE

Document overview

  • PDF pages: 16

Technical content

Page 1

PDF page 1 diagram
PDF page 1 diagram
PDF page 1 diagram

panel surface)

These small, compact connectors offer unique features available only from Hirose.

2. Waterproof construction

IP67 and 68 waterproof construction in the mated state IP67 : Left submerged in water at a depth of 1m for 30 minutes IP68 : Left submerged in water at a depth of 2m for 14 days

3. Push/pull lock

Waterproof connectors feature an easy to operate push/pull locks developed with our exclusive technology.

4. Light weight

3 and 6 contacts: 6g (plug + receptacle) 10 and 12 contacts: 9g (plug + receptacle)

5. Clamp structure

Our proprietary clamping method allows clamping the cable by simply tightening the cord ring.

6. Easy mating operation

The plug can be securely locked while holding it in your hand while mating. (Fig.2)

7. Mis-insertion prevention

Mating portions are polarized to avoid improper mating and connector damage.

8. Mating mark

Both the plug and the receptacle feature a white index mark on them which is used to quickly align the two interfaces for proper mating.(Fig.3)

9. Complies with the RoHS requirements

In consideration of environmental issues, we use only materials that comply with the RoHS Directive.

In cases where the application will demand a high level of reliability, such as automotive,

2018.6⑤

please contact a company representative for further information.

Page 2

Product Specifi cations

Ratings Current rating 5A (3 pos.) 2A (6,10,12 pos.) Operation Temperature Range -25ç to +85ç
Voltage rating 100V AC,140V DC(3,6 pos.) 30V AC,42V DC(10,12 pos.) StorageTemperature Range -10ç to +60ç
Characteristic Specifi cation Conditions
1. Contact resistance 5mø max. (3 pos.) 15mø max. (Solder type : 6, 10, and 12 pos.) 30mø max. (Through hole type: 6 and 12 pos.) 1A DC
2. Insulation resistance 1000Mø min. 100V DC
3. Withstanding voltage No fl ashover or insulation breakdown 300V AC / 1minute
4. Vibration No electrical discontinuity of 10µs or more Frequency : 10 to 55 Hz, single amplitude of 0.75mm, 1 cycle= 5min, 10 cycles in each of the 3 directions.
5. Durability (mating/un-mating) Contact resistance 10mø min.(3 pos.) Contact resistance 30mø min. (Solder type: 6, 10, and 12 pos.) Contact resistance 100mø min. (Through hole type: 6 and 12 pos.) 1000 cycles
6. Temperature cycle Insulation resistance 100Mø min. (-55ç : 30 minutes → Room temperature : 10 to 15 minutes → +85ç : 30 minutes → Room temperature : 10 to 15 minutes) for 5 cycles
7. Humidity resistance Insulation resistance 10Mø min. (when humidity high) 100Mø min. (when dry) 96 hours at temperature of 40ç and humidity of 90% to 95%
8. Waterproof performance No water penetration inside. While mated with corresponding or protective cap submerged at depth of 1m for half hour.

Material / Finish

Assembly Component Material Finish Remarks
Plug Insulator PPS Black UL94V-0
PBT Black UL94V-0
Polyacetal Natural ----------
Gasket Silicone rubber, chloroprene rubber Red/Black ----------
Contacts Brass, phosphor bronze, Copper compound metal Gold plated ----------
Spring Stainless steel ---------- ----------
Receptacles Insulator PPS Black UL94V-0
Gasket Chloroprene rubber Black ----------
Contacts Brass, phosphor bronze, Copper compound metal Gold plated ----------
Hexagonal nut Zinc alloy Chromate ----------
Washer Phosphor bronze Nickel plated ----------
Crimp contact (male/female) Contacts Phosphor bronze Selective gold plated ----------

Product Number Structure

Refer to the chart below when determining the product specifications from the product number. Please select from the product numbers listed in this catalog when placing orders.

HR30 - 6 P A - 6 S C (\* \*)

q w e r

t y u

i

q Model name : HR30 t Number of Contacts : 3, 6, 10 and 12
w Shell size : Outside diameter/plug mating side y Contact type S : Female contact P : Male contact
e Connector type : P : Plug Connector type : R : Receptacle Connector type : J : Jack
u Contact wiring type Blank : Solder C : Crimping D : Through hole
r Variation Blank : Standard A : Fine wire B : Over mold type
i Other specifications: A two-digit character is added to indicate other specifications as needed.

Page 3

PDF page 3 diagram
HR30-6P-6S (31) 6 1
5 2 43

A(Fully tightened)

Applicable

PDF page 3 diagram

(Representative example)

Part No. HRS No. A B Ap plicable cable diameter range Solder pot inner diameter Weight
HR30-6P-3S(31) 130-0004-1 31 29.8 12.6 4.2 to 5 1.1 mm 4g
HR30-6P-6S(31) 130-0010-4 31 0.8 mm
HR30-6P-6P(31) 130-0009-5 31 30.3
HR30-6PA-3S(71) 130-0021-0 71 29.8 3.5 to 4.3 1.1 mm
HR30-6PA-6S(71) 130-0019-9 71 0.8 mm
HR30-6PA-6P(71) 130-0020-8 71 30.3
HR30-7P-12S(71) 130-0027-7 71 39.8 15.5 6.2 to 7 0.6 mm 6.7g
HR30-8P-12P(71) 130-0026-4 71
PDF page 3 diagram

Applicable

A(Fully tightened)

PDF page 3 diagram

(Representative example)

Part No. HRS No. A Applicable cable diameter range Crimp contact Weight
HR30-7P-10SC(71) 130-0013-2 71 39.8 6.2 to 7 HR30-SC-211 6g
HR30-7P-12SC(71) 130-0014-5 71
HR30-8P-12PC(71) 130-0015-8 71 HR30-PC-211

Page 4

PDF page 4 diagram
PDF page 4 diagram
Part No. HRS No. A B C Solder pot inner diameter Weight
HR30-6PB-3S 130-0034-2 22.7 12.6 5.2 1.1 mm 3.1g
HR30-6PB-6S 130-0032-7 0.8 mm 2.9g
HR30-6PB-6P 130-0037-0 23.2
HR30-7PB-12S 130-0035-5 25.9 15.5 6.4 0.6 mm 4.7g
HR30-8PB-12P 130-0030-1 4.5g
PDF page 4 diagram
PDF page 4 diagram
Part No. HRS No. Crimp contact Weight
HR30-7PB-10SC 130-0036-8 HR30-SC-211 4.1g
HR30-7PB-12SC 130-0033-0
HR30-8PB-12PC 130-0031-4 HR30-PC-211 4.3g

Page 5

PDF page 5 diagram

A

PDF page 5 diagram

Gasket

5

E(Thread)

F(Hex nut)

(Representative example)

Part No. HRS No. A B C D E F Solder p ot inner diameter Weight
HR30-6R-3P(71) 130-1003-4 71 16 8.3 12 8 .9 M8∞0.75 10 1.1mm 2g
HR30-6R-6P(71) 130-1009-0 71 0.8mm
HR30-6R-6S(71) 130-1008-8 71 18.4
HR30-7R-12P(31) 130-1016-6 31 18.6 9.3 15 11 .5 M11∞1 13 0.6mm 3.4g
HR30-8R-12S(31) 130-1018-1 31
PDF page 5 diagram
PDF page 5 diagram
Part No. HRS No. Crimp contact Weight
HR30-7R-10PC(31) 130-1012-5 31 HR30-PC-211 3g
HR30-7R-12PC(31) 130-1013-8 31
HR30-8R-12SC(31) 130-1014-0 31 HR30-SC-211
PDF page 5 diagram
PDF page 5 diagram
Part No. HRS No. A B C D E F Weight
HR30-6R-6PD(71) 130-1020-3 71 14.9 8.3 12 8 .9 M8∞0.75 10 2g
HR30-6R-6SD(71) 130-1021-6 71 15.2
HR30-7R-12PD(31) 130-1017-9 31 16 9.3 15 11 .5 M11∞1 13 3.4g
HR30-8R-12SD(31) 130-1019-4 31

Page 6

PDF page 6 diagram

Applicable

B(Fully tightened)

PDF page 6 diagram

(Representative example)

Part No. HRS No. A B Ap plicable cable diameter range Solder pot inner diameter Weight
HR30-6J-6P(31) 130-2009-6 31 12 28.8 4.2 to 5 0.8 mm 3g
HR30-6JA-6P(71) 130-2018-7 71 3.5 to 4.3
HR30-7J-12P(71) 130-2020-9 71 15 37.3 6.2 to 7 0.6 mm 5.7g
HR30-8J-12S(71) 130-2019-0 71 5.9g
PDF page 6 diagram

37.3 (Fully tightened)

Applicable

PDF page 6 diagram

(Representative example)

Part No. HRS No. Applicable cable diameter range Crimp contact Weight
HR30-7J-10PC(71) 130-2015-9 71 6.2 to 7 HR30-PC-211 5g
HR30-7J-12PC(71) 130-2017-4 71
HR30-8J-12SC(71) 130-2016-1 71 HR30-SC-211

Page 7

PDF page 7 diagram
PDF page 7 diagram
Part No. HRS No. A B C Solder pot inner diameter Weight
HR30-6JB-3P 130-2029-0 12.7 21.7 5.2 1.1mm 2.3g
HR30-6JB-6P 130-2021-1 12 0.8mm 2.2g
HR30-6JB-6S 130-2028-0 12.7 2.3g
HR30-7JB-12P 130-2023-7 15 23.7 6.4 0.6mm 3.6g
HR30-8JB-12S 130-2024-0 4.1g
PDF page 7 diagram
PDF page 7 diagram
Part No. HRS No. Crimp contact Weight
HR30-7JB-10PC 130-2025-2 HR30-PC-211 HR30-SC-211 3.1g
HR30-7JB-12PC 130-2022-4
HR30-8JB-12SC 130-2026-5

Page 8

PDF page 8 diagram
PDF page 8 diagram

(Representative example)

Part No. HRS No. A B C D E Applicable cable diameter Weight
HR30-6P-C(31) 130-3000-7 31 13 8.4 8.9 4 8.8 Ø4.2 to 5 1g
HR30-7P-C(31) 130-3004-8 31 16 10.4 10.5 6 1 1.4 Ø6.2 to 7 2g
HR30-8P-C(31) 130-3003-5 31
PDF page 8 diagram
PDF page 8 diagram
PDF page 8 diagram

(Representative example)

Part No. HRS No. A B C D E Remarks Weight
HR30-6R-C(31) 130-3001-0 31 12.6 11.8 7.5 12.1 9.1 1g
HR30-7R-C(31) 130-3002-2 31 15.5 14.8 8.5 15 1 This cap fi ts each size of 2.1 the HR30-7R and HR30-8R receptacles

Note : When using these caps, do not use the gasket that is normally supplied with the receptacle. The “B” diameter end of the receptacle cap will serve as the gasket.

Page 9

Crimp Contacts

Male contact

Female contact

1.2

1.2

PDF page 9 diagram
PDF page 9 diagram

A-A cross-section

(Representative example)

A-A cross-section

(Representative example)

Type Part No. HRS No. Packaging type Weight
Loose contact HR30-SC-111 130-0023-6 100pcs/pack 0.03g/1 pin
Reel contact HR30-SC-211 130-0017-3 10,000pcs/reel 0.03g/1 pin
Type Part No. HRS No. Packagin type g Weight
Loose contact HR30-PC-111 130-0022-3 100pcs/pac k 0.03g/1 pin
Reel contact HR30-PC-211 130-0016-0 10,000pcs/r eel 0.03g/1 pin

Note : Use wire size 26 to 30 AWG with a jacket diameter of 1 mm max.

Diagrams of Connectors in Combination

Plugs

Receptacles

HR30-\*P-\*\*(71)

HR30-\*R-\*\*(71)

PDF page 9 diagram

Note 1 : Please use connectors with compatible shell size and number of contacts. If you are using a male contact plug, please also use a corresponding product with a female receptacle and a jack. Note 2 : Please install the applicable crimping contacts when using the crimping style connectors. (Please refer to the manual for wiring work.) Note 3 : When using the cap on the receptacle side, do not use the gasket that is normally supplied with the receptacle. The Hirose cap has the necessary gasket as part of the cap unit.

Cap mounting diagram

Panel

PDF page 9 diagram
PDF page 9 diagram

Page 10

Applicable Tools

Cable Assembly Tools

Part No. HRS No. Applicable Connectors
Shell size Connector type No. of contacts Contact type
HR30-6P-3S-T01 150-0220-1 6 Plug 3 Female
HR30-6P-6S-T01 150-0214-9 6 Female
HR30-6P-6P-T01 150-0221-4 Male
HR30-7P-10SC-T01 150-0228-3 7 Plug 10 Female
HR30-7P-12SC-T01 150-0223-0 12 Female
HR30-8P-12PC-T01 150-0227-0 8 Plug 12 Male
HR30-6R-3P-T01 150-0225-5 6 Receptacle Jack 3 Male
HR30-6R-6P-T01 150-0218-0 6 Male
HR30-6R-6S-T01 150-0222-7 Female
HR30-7J-10PC-T01 150-0231-8 7 Receptacle Jack 10 Male
HR30-7J-12PC-T01 150-0230-5 12 Male
HR30-8J-12SC-T01 150-0226-8 8 Female

Note : Wiring for soldering or disassembly and assembly of plugs and jacks can be accomplished more effi ciently when using the cable assembly tool.

Tightening collar for back shell

Part No. HRS No. Applicable Connectors
HR30-6P-T02 150-0216-4 3 and 6 contacts
HR30-8P-T02 150-0224-2 10 and 12 contacts

Note : The code ring tightening collar is used to tighten the cord ring to the specifi ed torque. (Please refer to the manual for assembly procedures.)

PDF page 10 diagram

Page 11

Applicable Tools

PDF page 11 diagram

Receptacle, Board Mounting Through Hole Pattern

PDF page 11 diagram
PDF page 11 diagram
PDF page 11 diagram

6R-6PD

6R-6SD

7R-12PD

8R-12SD

Remark : 1. The receptacle through hole confi guration depicts a view from the mating side of the connector. 2.The above Δ mark indicates the guide key position. 3.The recommended board maximum thickness :1.2mm. 4. Tolerance of +0.03mm is recommended for the plated through hole location. Tolerance of +0.02mm is recommended for the plated through hole diameter.

Contact Position Arrangement

Panel Cutout

Alignment mark

Alignment mark

+0.05

PDF page 11 diagram

1 6

5 1

1 3

6

2 5

4 2 3

3 4

2

HR30-6P-3S(\*\*)

HR30-6P-6S(\*\*)

HR30-6P-6P(\*\*)

1 2 3

3 2 1

3 2 1

4 5 6 7

7 6 5 4

7 6 5 4

A B C D Panel Thishness
3,6 pos. 1.25 6.45 8. 05 3.95 0.7 to 2
10,12 pos. 1.35 9.25 11. 05 5.45 0.7 to 3

8 9 10

10 9 8

10 9 8

12 11

11 12

HR30-7P-10SC(\*\*) HR30-7P-12SC(\*\*) HR30-8P-12PC(\*\*)

Remarks : 1. The contact arrangement depicts a view from the wiring side. 2. Installation is accomplished by securing the receptacle from the back side of the panel using the supplied hexagon nut. The tightening torque of the hexagon nut should be 0.5 N·m for 3, 6 contacts, and 0.8 N·m for 10, 12 contacts.

In addition, in order to prevent loosening, please apply Locktight 263 and Lockprimer 7649 manufactured by Henkel Japan Ltd., Tokyo.

Page 12

Assembly Procedures

Plug Assembly Sequence
1 Push/pull locking collar Seal bushing Insulator/contact assembly Back shell Spring Strain relief A B Cable A B Solder type : 3 and 6 Contacts. 2mm 5.5mm max. Solder type : 12 Contacts. 2mm 10mm max. Crimp type : 10 and 12 Contacts. 2 --0 0.5mm 15 to 20mm
Insert the cable in the following order : 1. Back shell, 2. cord clamp, 3. gasket, 4, spring and 5. locking collar. Prepare the cable end according to the dimensions shown in Table 1. Note : When preparing the cable, use caution not to damage the insulation and conductors of the lead wires.
2 Block end face Insulator/contact assembly Solder termination fixture
Solder type Fix the P case block on the cable termination tool, and after preliminary soldering, solder for 3 to 4 seconds with the soldering iron at 350±10ç. Note 1 : T ake care to avoid creating cold solder joints and solder joints with voids or air holes in it. Also check to make sure the solder joint is adequately fused between the lead wires and solder cup. Note 2 : The P case block is a precision unit. Please use caution when soldering the P case block so it does not become damaged. Any damage could result in loss of the waterproof performance. Crimp type After crimping the appropriate contact to the cable lead wire, insert the terminated wire into the correct contact position on the P case block. Note : A fter inserting the crimping wire/contact, slightly pull the lead wire and check if the crimping contact is properly seated into the P case block.
A B
der type : 3 and 6 Contacts. 2mm 5.5mm max.
der type : 12 Contacts. 2mm 10mm max.
mp type : 10 and 12 Contacts. 2 --0 0.5mm 15 to 20mm

Page 13

3 Fixation Cable Push/pull Back shell Cable locking collar Guide keys Tightening collar for back shell A (Refer to Table-2) Plug insulator body Solder termination fixture Cable View A (2:1) Groove - sealing bushing Front edge of cable jacket Fig.B Fig.C Table-2 Connector Back shell tightening collar size Torque 3 and 6 Contacts. 16mm 0.5N.m 10 and 12 Contacts. 18mm 0.5N.m
Insert the cable by fitting the coupling guide to the wire-connected P case block. Then, pass the cable through and assemble in the following order: 1. spring, gasket, 2 cord clamp, and 3. cord tube. Make sure when assembling it with the cord clamp and cord tube, to maintain the positional relations between the cable sheath end face and the concave area of the gasket as shown in Fig.B. Note : Please install the cord tube using the cord tube tightening tool with the cord ring tightening torque shown in Table-2. ln addition, in order to prevent loosening, please apply Locktight 263 and Lockprimer 7649 manufactured by Henkel Japan Ltd., Tokyo. When screwing in the cord tube, use your hand to hold the cable so that the cable will not rotate or twist and apply stress to the soldered wires. However, as the cable tends to be twisted slightly (just over one rotation), we recommend that you twist it in the opposite direction in advance.
Back shell tightening collar size Torque
16mm 0.5N.m
18mm 0.5N.m

Page 14

Points to note when using Heat shrink tubing

We recommend that you use shrink tubing over the solder connections in order to protect the soldered wires and to enhance insulation. However, please be careful when applying heat in this area when installing the shrink tube so excess heat does not bleed into or affect the resin parts as shown in the figure below.

If the product does become heated beyond the area shown and into the resin parts, please make sure to prevent the following. q Deformation of the C ring. This could result in prevention of locking during mating. w Melting of some parts. To prevent the deformation of the C rings of the receptacles and the jack, we recommend heat to be applied after mating with a compatible plug. Before heating, please mate the plug in the receptacle securely, then pull the back shell for checking whether it is locked properly. If it is heated with semi-fitting, C ring may be thermally deformed with shrinking condition and it may not be locked properly.

C ring

PDF page 14 diagram

Heat application area

Mated dimensions

Compatible plug

Receptacle

PDF page 14 diagram

Page 15

General usage notes

1. Mating 2. Un-mating
Mounting panel Receptacle Cable D Plug C A D Alignment marks C Mounting panel Push/pull locking collar Cable B
When mounting, smooth mating will be achieved by holdi plug in any are “A” and aligning the arrow of the plug with that of the receptacle, then pushing the plug straight in. ng When removing the plug from its connected condition, hold the plug by push/pull locking collar (area “B”) and pull straight off.

Precautions

  1. Make sure the power is off before mating or un-mating the connector. 2. When mating the connector, push it on with a force of a least 30N. After mating, pull slightly on the connector to check for proper mating and to ensure the connector is fi rmly locked to the receptacle. 3. After mating the connector, do not apply a force over 30N to the cable in the directions shown by the arrows. An excessive load can lead to connector damage.
PDF page 15 diagram
  1. To maintain the waterproof performance, cable clamping force and cable stability, please use a cable within the recommended for cable diameters. Because the performance will differ depending on the cable structure, make sure to check all specifi cations of the cable assembly before use or production. 5. Please assemble and install the connector and components with the specifi ed tightening torque. If the tightening torque is too weak or too strong, loosening or breakage can occur. 6.Please contact Hirose if your application requires compliance with the Electrical Appliance and Meterial Safety Act.

Page 16

USA:

USA:

HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS CHICAGO OFFICE HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE

2300 Warrenville Road, Suite 150,

2841 Junction Ave, Suite 200

Downers Grove, IL 60515

San Jose, CA. 95134

Phone : +1-630-282-6700

Phone : +1-408-253-9640

http://www.hirose.com/us/

Fax : +1-408-253-9641 http://www.hirose.com/us/

USA:

THE NETHERLANDS:

HIROSE ELECTRIC (U.S.A.), INC. BOSTON OFFICE HIROSE ELECTRIC EUROPE B.V.

300 Brickstone Square Suite 201,

Hogehillweg #8 1101 CC Amsterdam Z-O

Andover, MA 01810

Phone : +31-20-6557460

Phone : +1-978-662-5255

Fax : +31-20-6557469 http://www.hirose.com/eu/

GERMANY:

GERMANY:

HIROSE ELECTRIC EUROPE B.V. NUREMBERG OFFICE HIROSE ELECTRIC EUROPE B.V. HANOVER OFFICE

Neumeyerstrasse 22-26, 90411 Nurnberg

Bayernstr. 3, Haus C 30855 Langenhagen, Germany Phone : +49-511 97 82 61 30

Phone : +49-911 32 68 89 63

Fax : +49-511 97 82 61 35

Fax : +49-911 32 68 89 69

http://www.hirose.com/eu/

http://www.hirose.com/eu/

UNITED KINGDOM:

CHINA:

HIROSE ELECTRIC (CHINA) CO., LTD. (SHANGHAI, HEADQUARTERS)

HIROSE ELECTRIC EUROPE BV (UK BRANCH)

18, Enterprise Center Tower 2, 209# Gong He

4 Newton Court, Kelvin Drive, Knowlhill,

Road, Jing’an District, Shanghai, CHINA 200070

Milton Keynes, MK5 8NH

Phone : +86-21-6391-3355

Phone : +44-1908 202050

Fax : +86-21-6391-3335

Fax : +44-1908 202058

http://www.hirose.com/cn/

http://www.hirose.com/eu/

CHINA:

HONG KONG:

HIROSE ELECTRIC (CHINA) CO., LTD. SHENZHEN BRANCH HIROSE ELECTRIC HONGKONG TRADING CO., LTD.

Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre, Room 1001, West Wing, Tsim Sha Tsui Centre, 66

Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong

5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008 Phone : +86-755-8207-0851

Phone : +852-2803-5338

Fax : +86-755-8207-0873

Fax : +852-2591-6560

http://www.hirose.com/cn/

http://www.hirose.com/hk/

SINGAPORE:

KOREA:

HIROSE ELECTRIC SINGAPORE PTE. LTD.

HIROSE KOREA CO.,LTD.

143, Gongdan 1-daero, Siheung-si,

03, Anson Road, #20-01, Springleaf Tower,

Gyeonggi-do, 15084, Korea

Singapore 079909

Phone : +82-31-496-7000

Phone : +65-6324-6113 Fax : +65-6324-6123

Fax : +82-31-496-7100

http://www.hirose.com/sg/

http://www.hirose.co.kr/

MALAYSIA:

INDIA:

HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE PENANG REPRESENTATIVE OFFICE

Unit No-403, 4th Floor, No-84, Barton Centre, Mahatma 73-3-1, Ideal@The One, Jalan Mahsuri, Bayan Gandhi (MG) Road, Bangalore 560 001, Karnataka, India

Lepas Penang, 11950, Malaysia

Phone : +91-80-4120 1907

Phone : +604-648-5536

Fax : +91-80-4120 9908

http://www.hirose.com/sg/

http://www.hirose.com/sg/

PDF page 16 diagram

USA:

HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE)

17197 N. Laurel Park Drive, Suite 253, Livonia, MI 48152 Phone : +1-734-542-9963 Fax : +1-734-542-9964 http://www.hirose.com/us/

GERMANY: HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH

Schoenbergstr. 20, 73760 ostfildern Phone : +49-711-456002-1 Fax : +49-711-456002-299 http://www.hirose.com/eu/

FRANCE: HIROSE ELECTRIC EUROPE B.V. PARIS OFFICE

130 Avenue Joseph Kessel, Bat E, 78960 Voisins le Bretonneux, France Phone : +33-1-85764886 Fax : +33-1-85764823 http://www.hirose.com/eu/

CHINA: HIROSE ELECTRIC (CHINA) CO.,LTD. BEIJING BRANCH

A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, ChaoYang District, Beijing, 100025 Phone : +86-10-5165-9332 Fax : +86-10-5908-1381 http://www.hirose.com/cn/

TAIWAN: HIROSE ELECTRIC TAIWAN CO., LTD.

103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377 Fax : +886-2-2555-7355 http://www.hirose.com/tw/

INDIA:

HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE

Office NO.552, Regus-Green Boulevard, Level5, Tower C, Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India Phone : +91-12-660-8018 Fax : +91-120-4804949 http://www.hirose.com/sg/

THAILAND: BANGKOK OFFICE (REPRESENTATIVE OFFICE)

Unit 4703, 47th FL., 1 Empire Tower, South Sathorn Road, Yannawa, Sathorn, Bangkok 10120 Thailand Phone : +66-2-686-1255 Fax : +66-2-686-3433 http://www.hirose.com/sg/

2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com

The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 06/2018. Contents are subject to change without notice for the purpose of improvements.