HGTP7N60C3D_05 FAIRCHILD

Document overview

  • PDF pages: 9

Technical content

Page 1

September 2005

14A, 600V, UFS Series N-Channel IGBT with Anti-Parallel Hyperfast Diodes

General Description

The HGTP7N60C3D, HGT1S7N60C3DS and HGT1S7N60C3D are MOS gated high voltage switching devices combining the best features of MOSFETs and bipolar transistors. These devices have the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between 25oC and 150oC. The IGBT used is developmental type TA49115. The diode used in anti-parallel with the IGBT is developmental type TA49057.

The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.

Formerly Developmental Type TA49121.

JEDEC TO-220AB COLLECTOR (FLANGE)

EMITTER COLLECTOR GATE

JEDEC TO-262

PDF page 1 diagram

COLLECTOR

COLLECTOR (FLANGE)

Features

„ 4A, 600V at TC = 25oC

„ 600V Switching SOA Capability

„ Typical Fall Time...................140ns at TJ = 150oC

„ Short Circuit Rating

„ Low Conduction Loss

„ Hyperfast Anti-Parallel Diode

JEDEC TO-263AB

GATE

COLLECTOR (FLANGE)

EMITTER

C

G

E

FAIRCHILD SEMICONDUCTOR IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,364,073

4,417,385

4,430,792

4,443,931

4,466,176

4,516,143

4,532,534

4,587,713

4,598,461

4,605,948

4,620,211

4,631,564

4,639,754

4,639,762

4,641,162

4,644,637

4,682,195

4,684,413

4,694,313

4,717,679

4,743,952

4,783,690

4,794,432

4,801,986

4,803,533

4,809,045

4,809,047

4,810,665

4,823,176

4,837,606

4,860,080

4,883,767

4,888,627

4,890,143

4,901,127

4,904,609

4,933,740

4,963,951

4,969,027

©2005 Fairchild Semiconductor Corporation

Page 2

Absolute Maximum Ratings TA = 25°C unless otherwise noted

Symbol Parameter Ratings Units
BV CES Collector to Emitter Voltage 600 V
I C25 Collector Current Continuous At T = 25oC C 14 A
I C110 Collector Current Continuous At T = 110oC C 7 A
I(AVG) Average Diode Forward Current at 110oC 8 A
I CM Collector Current Pulsed (Note 1) 56 A
V GES Gate to Emitter Voltage Continuous ±20 V
V GEM Gate to Emitter Voltage Pulsed ±30 V
SSOA Switching Safe Operating Area at T = 150oC (Figure 14) J 40A at 480V
P D Power Dissipation Total at T = 25oC C 60 W
Power Dissipation Derating T > 25oC C 0.487 W/oC
T , T J STG Operating and Storage Junction Temperature Range -40 to 150 oC
T L Maximum Lead Temperature for Soldering 260 oC
t SC Short Circuit Withstand Time (Note 2) at V = 15V GE 1 µs
Short Circuit Withstand Time (Note 2) at V = 10V GE 8 µs

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES: 1. Repetitive Rating: Pulse width limited by maximum junction temperature. 2. VCE(PK) = 360V, TJ = 125oC, RG = 50W.

Thermal Characteristics

R θJC Thermal Resistance IGBT 2.1 oC/W
Thermal Resistance Diode 2.0 oC/W

Package Marking and Ordering Information

Part Number Package Brand
HGTP7N60C3D TO-220AB G7N60C3D
HGT1S7N60C3DS TO-263AB G7N60C3D
HGT1S7N60C3D TO-262 G7N60C3D

NOTES:When ordering, use the entire part number. Add the suffix 9A to obtain the TO-263AB variant in tape and reel, i.e. HGT1S7N60C3DS9A.

Page 3

PDF page 3 diagram
PDF page 3 diagram

On Characteristics

V GE(TH) Gate-Emitter Threshold Voltage I = 250µA, V = V , C CE GE T = 25oC C 3.0 5.0 6.0 V
SSOA Switching SOA T = 150oC, J R = 50Ω , G V = 15V, GE L = 1mH V = 480V CE(PK) 40 - - A
V = 600V CE(PK) 60 - - A
V GEP Gate to Emitter Plateau Voltage I = I , V = 0.5 BV C C110 CE CES - 8 - V

Switching Characteristics

t d(ON)I Current Turn-On Delay Time T = 150oC J I = I CE C110 V = 0.8 BV CE(PK) CES V = 15V GE R = 50Ω G L = 1mH - 8.5 - ns
t rI Current Rise Time - 11.5 - ns
t d(OFF)I Current Turn-Off Delay Time - 350 400 ns
t fI Current Fall Time - 140 275 ns
E ON Turn-On Energy - 165 - µJ
E OFF Turn-Off Energy (Note 3) - 600 - µJ
Q G(ON) On-State Gate Charge I = I , C C110 V = 0.5 BV CE CES V = 15V GE - 23 30 nC
V = 20V GE - 30 38 nC

Drain-Source Diode Characteristics and Maximum Ratings

V EC Diode Forward Voltage I = 7A EC - 1.9 2.5 V
t rr Diode Reverse Recovery Time I = 7A, dI /dt = 200A/µs EC EC - 25 37 ns
I = 1A, dI /dt = 200A/µs EC EC - 18 30 ns
PDF page 3 diagram

Page 4

PDF page 4 diagram

Page 5

PDF page 5 diagram

Page 6

PDF page 6 diagram

Page 7

PDF page 7 diagram

Page 8

Handling Precautions for IGBTs

Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:

Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as ECCOSORBD™ LD26 or equivalent.

When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband.

Tips of soldering irons should be grounded.

Devices should never be inserted into or removed from circuits with power on.

Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region.

Gate Termination - The gates of these devices are essentially capacitors. Circuits that leave the gate opencircuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup.

Gate Protection - These devices do not have an internal monolithic zener diode from gate to emitter. If gate protection is required an external zener is recommended.

Operating Frequency Information

Operating frequency information for a typical device (Figure 13) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 4, 7, 8, 11 and 12. The operating frequency plot (Figure 13) of a typical device shows fMAX1 or fMAX2 whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.

fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I + td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 21.

Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM . td(OFF)I is important when controlling output ripple under a lightly loaded condition.

fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD . A 50% duty factor was used (Figure 13) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2.

EON and EOFF are defined in the switching waveforms shown in Figure 21. EON is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss during turn-off. All tail losses are included in the calculation for EOFF; i.e. the collector current equals zero (ICE = 0).

Page 9

TRADEMARKS

The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.

FACT™

i-Lo™

ACEx™

PACMAN™

SPM™

FACT Quiet Series™ ImpliedDisconnect™

ActiveArray™

POP™

Stealth™

FAST®

IntelliMAX™

Bottomless™

Power247™

SuperFET™

Build it Now™ FASTr™

ISOPLANAR™

PowerEdge™

SuperSOT™-3

FPS™

LittleFET™

CoolFET™

PowerSaver™

SuperSOT™-6

MICROCOUPLER™

CROSSVOLT™ FRFET™

GlobalOptoisolator™ MicroFET™

DOME™

GTO™

MicroPak™

EcoSPARK™ E2CMOS™

HiSeC™

MICROWIRE™

I2C™

EnSigna™

MSX™ MSXPro™

Across the board. Around the world.™ OCX™ The Power Franchise®

OCXPro™ OPTOLOGIC®

Programmable Active Droop™

OPTOPLANAR™

DISCLAIMER

PowerTrench®

SuperSOT™-8

QFET®

SyncFET™ TinyLogic®

QS™ QT Optoelectronics™ TINYOPTO™ Quiet Series™

TruTranslation™

RapidConfigure™

UHC™ UltraFET®

RapidConnect™

UniFET™

µSerDes™ SILENT SWITCHER® VCX™ SMART START™

Wire™

FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.

As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.

PRODUCT STATUS DEFINITIONS

Definition of Terms

  1. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Datasheet Identification Product Status Definition
Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice.
Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only.

Rev. I16