HGTP7N60B3D INTERSIL
Document overview
- PDF pages: 7
Technical content
Page 1
Data Sheet
14A, 600V, UFS Series N-Channel IGBTs
with Anti-Parallel Hyperfast Diode
The HGTP7N60B3D and HGT1S7N60B3DS are MOS gated high voltage switching devices combining the best features of MOSFETs and bipolar transistors. These devices have the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between 25oC and 150oC at rated current. The IGBT is developmental type TA49190. The diode used in anti-parallel with the IGBT is the RHRD660 (TA49057).
The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.
Formerly Developmental Type TA49191.
Ordering Information
| PART NUMBER | PACKAGE | BRAND |
|---|---|---|
| HGTP7N60B3D | TO-220AB ALT | G7N60B3D |
| HGT1S7N60B3DS | TO-263AB | G7N60B3D |
NOTE: When ordering, use the entire part number. Add the suffix 9A to obtain the TO-263AB variant in tape and reel, i.e., HGT1S7N60B3DS9A.
Symbol
C
G
E
January 2000
File Number 4413.2
Features
- 14A, 600V, TC = 25oC
- 600V Switching SOA Capability
- Typical Fall Time. . . . . . . . . . . . . . . . 120ns at TJ = 150oC
- Short Circuit Rating
- Low Conduction Loss
- Hyperfast Anti-Parallel Diode
Packaging
JEDEC TO-220AB (ALTERNATE VERSION)
E C G
COLLECTOR
(FLANGE)
JEDEC TO-263AB
COLLECTOR
(FLANGE)
G E
INTERSIL CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS
4,364,073
4,417,385
4,430,792
4,443,931
4,466,176
4,516,143
4,532,534
4,587,713
4,598,461
4,605,948
4,620,211
4,631,564
4,639,754
4,639,762
4,641,162
4,644,637
4,682,195
4,684,413
4,694,313
4,717,679
4,743,952
4,783,690
4,794,432
4,801,986
4,803,533
4,809,045
4,809,047
4,810,665
4,823,176
4,837,606
4,860,080
4,883,767
4,888,627
4,890,143
4,901,127
4,904,609
4,933,740
4,963,951
4,969,027
CAUTION: These devices are sensitive to electrostatic discharge; follow proper ESD Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000
Page 2
| Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified ALL TYPES UNITS Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BVCES 600 V Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25 14 A At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110 7 A Average Rectified Forward Current at TC = 152oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IF(AV) 6 A Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM 56 A Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGES ±20 V Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM ±30 V Switching Safe Operating Area at TJ = 150oC (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . SSOA 35A at 600V Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 60 W Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.476 W/oC Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG -55 to 150 oC Maximum Lead Temperature for Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 260 oC Short Circuit Withstand Time (Note 2) at VGE = 15V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC 2 µs Short Circuit Withstand Time (Note 2) at VGE = 10V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC 12 µs CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Single Pulse; Pulse width limited by maximum junction temperature. Parts may current limit at less than ICM. 2. VCE(PK) = 360V, TJ = 125oC, RG = 50Ω. | |||||||
|---|---|---|---|---|---|---|---|
| Electrical Specifications TC = 25oC, Unless Otherwise Specified | |||||||
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS | |
| Collector to Emitter Breakdown Voltage | BVCES | IC = 250µA, VGE = 0V | 600 | - | - | V | |
| Collector to Emitter Leakage Current | ICES | VCE = BVCES | TC = 25oC | - | - | 100 | µA |
| TC = 150oC | - | - | 3.0 | mA | |||
| Collector to Emitter Saturation Voltage | VCE(SAT) | IC = IC110, VGE = 15V | TC = 25oC | - | 1.8 | 2.1 | V |
| TC = 150oC | - | 2.1 | 2.4 | V | |||
| Gate to Emitter Threshold Voltage | VGE(TH) | IC = 250µA, VCE = VGE | 3.0 | 5.1 | 6.0 | V | |
| Gate to Emitter Leakage Current | IGES | VGE = ±20V | - | - | ±100 | nA | |
| Switching SOA | SSOA | TJ = 150oC, RG = 50Ω, VGE = 15V, L = 100µH | VCE = 480V | 42 | - | - | A |
| VCE = 600V | 35 | - | - | A | |||
| Gate to Emitter Plateau Voltage | VGEP | IC = IC110, VCE = 0.5 BVCES | - | 7.7 | - | V | |
| On-State Gate Charge | QG(ON) | IC = IC110, VCE = 0. 5BVCES | VGE = 15V | - | 23 | 28 | nC |
| VGE = 20V | - | 30 | 37 | nC | |||
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode Both at TJ = 25oC, ICE = IC110, VCE = 0.8 BVCES, VGE = 15V, RG = 50Ω, L = 2mH, Test Circuit (Figure 19) | - | 26 | - | ns | |
| Current Rise Time | trI | - | 21 | - | ns | ||
| Current Turn-Off Delay Time | td(OFF)I | - | 130 | 160 | ns | ||
| Current Fall Time | tfI | - | 60 | 80 | ns | ||
| Turn-On Energy | EON | - | 160 | 200 | µJ | ||
| Turn-Off Energy (Note 3) | EOFF | - | 120 | 200 | µJ | ||
Page 3
| Electrical Specifications TC = 25oC, Unless Otherwise Specified (Continued) | ||||||
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS |
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode Both at TJ = 150oC ICE = IC110, VCE = 0.8 BVCES, VGE = 15V, RG = 50Ω, L = 2mH, Test Circuit (Figure 19) | - | 24 | - | ns |
| Current Rise Time | trI | - | 22 | - | ns | |
| Current Turn-Off Delay Time | td(OFF)I | - | 230 | 295 | ns | |
| Current Fall Time | tfI | - | 120 | 175 | ns | |
| Turn-On Energy | EON | - | 310 | 350 | µJ | |
| Turn-Off Energy (Note 3) | EOFF | - | 350 | 500 | µJ | |
| Diode Forward Voltage | VEC | IEC = 7A | - | 1.85 | 2.2 | V |
| Diode Reverse Recovery Time | trr | IEC = 7A, dIEC/dt = 200A/µs | - | - | 37 | ns |
| IEC = 1A, dIEC/dt = 200A/µs | - | - | 32 | ns | ||
| Thermal Resistance Junction To Case | RθJC | IGBT | - | - | 2.1 | oC/W |
| Diode | - | - | 3.0 | oC/W | ||
| NOTE: 3. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss. Turn-On losses include losses due to diode recovery. Typical Performance Curves Unless Otherwise Specified 16 50 (A) VGE = 15V TJ = 150oC, RG = 50Ω, VGE = 15V (A) CURRENT 14 CURRENT 40 12 EMITTER 10 30 COLLECTOR 8 TO 20 6 COLLECTOR 4 DC 10 ICE, 2 ICE, 0 0 25 50 75 100 125 150 0 100 200 300 400 500 600 700 TC, CASE TEMPERATURE (oC) VCE, COLLECTOR TO EMITTER VOLTAGE (V) FIGURE 1. DC COLLECTOR CURRENT vs CASE FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA TEMPERATURE | ||||||

Page 4

Page 5

Page 6

Page 7
Test Circuit and Waveforms
L = 2mH
RHRD660
RG = 50Ω
+
VDD = 480V
-
FIGURE 19. INDUCTIVE SWITCHING TEST CIRCUIT
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken: 1. Prior to assembly into a circuit, all leads should be kept
shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are essentially capacitors. Circuits that leave the gate open-
circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.
90%
10%
VGE
EON
EOFF
VCE
90%
10%
ICE
td(OFF)I
trI
tfI
td(ON)I
FIGURE 20. SWITCHING TEST WAVEFORMS
Operating Frequency Information
Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.
fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 20. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.
fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON and EOFF are defined in the switching waveforms shown in Figure 20. EON is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site www.intersil.com
ECCOSORBD™ is a Trademark of Emerson and Cumming, Inc.