HGT1S7N60A4S9A_04 FAIRCHILD
Document overview
- PDF pages: 8
Technical content
Page 1
Data Sheet
600V, SMPS Series N-Channel IGBT
The HGT1S7N60A4S9A, HGTG7N60A4 and HGTP7N60A4 are MOS gated high voltage switching devices combining the best features of MOSFETs and bipolar transistors. These devices have the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between 25oC and 150oC.
This IGBT is ideal for many high voltage switching applications operating at high frequencies where low conduction losses are essential. This device has been optimized for high frequency switch mode power supplies.
Formerly Developmental Type TA49331.
Ordering Information
| PART NUMBER | PACKAGE | BRAND |
|---|---|---|
| HGT1S7N60A4S9A | TO-263AB | G7N60A4 |
| HGTG7N60A4 | TO-247 | G7N60A4 |
| HGTP7N60A4 | TO-220AB | G7N60A4 |
NOTE: When ordering, use the entire part number.
Packaging
JEDEC STYLE TO-247
E

(BOTTOM SIDE METAL)
HGT1S7N60A4S9A, HGTG7N60A4
HGTP7N60A4
September 2004
Features
- >100kHz Operation at 390V, 7A
- 200kHz Operation at 390V, 5A
- 600V Switching SOA Capability
- Typical Fall Time . . . . . . . . . . . . . . . . . . . 75ns at TJ = 125oC
- Low Conduction Loss
Symbol
C
G
E
JEDEC TO-220AB

COLLECTOR
JEDEC TO-263AB
COLLECTOR
G
(FLANGE)
E
FAIRCHILD CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS
4,364,073
4,417,385
4,430,792
4,443,931
4,466,176
4,516,143
4,532,534
4,587,713
4,598,461
4,605,948
4,620,211
4,631,564
4,639,754
4,639,762
4,641,162
4,644,637
4,682,195
4,684,413
4,694,313
4,717,679
4,743,952
4,783,690
4,794,432
4,801,986
4,803,533
4,809,045
4,809,047
4,810,665
4,823,176
4,837,606
4,860,080
4,883,767
4,888,627
4,890,143
4,901,127
4,904,609
4,933,740
4,963,951
4,969,027
Page 2
Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified
ALL TYPES
UNITS
600
V
Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BVCES Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25
34
A
At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110
14
A
56
A
Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ICM Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGES
±20
V
±30
V
Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM Switching Safe Operating Area at TJ = 150oC, Figure 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .SSOA
35A at 600V
Single Pulse Avalanche Energy at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAS
25mJ at 7A
Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD
125
W
Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W/oC
1.0
oC
Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG
-55 to 150
Maximum Lead Temperature for Soldering
oC
300
Leads at 0.063in (1.6mm) from Case for 10s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TL
oC
Package Body for 10s, See Tech Brief 334 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TPKG
260
CAUTION: Stresses above those listed in “Device Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: 1. Pulse width limited by maximum junction temperature.
Electrical Specifications TJ = 25oC, Unless Otherwise Specified
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS | |
|---|---|---|---|---|---|---|---|
| Collector to Emitter Breakdown Voltage | BVCES | IC = 250µA, VGE = 0V | 600 | - | - | V | |
| Emitter to Collector Breakdown Voltage | BVECS | IC = -10mA, VGE = 0V | 20 | - | - | V | |
| Collector to Emitter Leakage Current | ICES | VCE = 600V | TJ = 25oC | - | - | 250 | µA |
| TJ = 125oC | - | - | 2 | mA | |||
| Collector to Emitter Saturation Voltage | VCE(SAT) | IC = 7A, VGE = 15V | TJ = 25oC | - | 1.9 | 2.7 | V |
| TJ = 125oC | - | 1.6 | 2.2 | V | |||
| Gate to Emitter Threshold Voltage | VGE(TH) | IC = 250µA, VCE = 600V | 4.5 | 5.9 | 7.0 | V | |
| Gate to Emitter Leakage Current | IGES | VGE = ±20V | - | - | ±250 | nA | |
| Switching SOA | SSOA | TJ = 150oC, RG = 25Ω, VGE = 15V L = 100µH, VCE = 600V | 35 | - | - | A | |
| Pulsed Avalanche Energy | EAS | ICE = 7A, L = 500µH | 25 | - | - | mJ | |
| Gate to Emitter Plateau Voltage | VGEP | IC = 7A, VCE = 300V | - | 9.0 | - | V | |
| On-State Gate Charge | Qg(ON) | IC = 7A, VCE = 300V | VGE = 15V | - | 37 | 45 | nC |
| VGE = 20V | - | 48 | 60 | nC | |||
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode at TJ = 25oC ICE = 7A VCE = 390V VGE = 15V RG = 25Ω L = 1mH Test Circuit (Figure 20) | - | 11 | - | ns | |
| Current Rise Time | trI | - | 11 | - | ns | ||
| Current Turn-Off Delay Time | td(OFF)I | - | 100 | - | ns | ||
| Current Fall Time | tfI | - | 45 | - | ns | ||
| Turn-On Energy (Note 2) | EON1 | - | 55 | - | µJ | ||
| Turn-On Energy (Note 2) | EON2 | - | 120 | 150 | µJ | ||
| Turn-Off Energy (Note 3) | EOFF | - | 60 | 75 | µJ | ||
Page 3
Electrical Specifications TJ = 25oC, Unless Otherwise Specified (Continued)
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode at TJ = 125oC ICE = 7A VCE = 390V VGE = 15V RG = 25Ω L = 1mH Test Circuit (Figure 20) | - | 10 | - | ns |
| Current Rise Time | trI | - | 7 | - | ns | |
| Current Turn-Off Delay Time | td(OFF)I | - | 130 | 150 | ns | |
| Current Fall Time | tfI | - | 75 | 85 | ns | |
| Turn-On Energy (Note 2) | EON1 | - | 50 | - | µJ | |
| Turn-On Energy (Note 2) | EON2 | - | 200 | 215 | µJ | |
| Turn-Off Energy (Note 3) | EOFF | - | 125 | 170 | µJ | |
| Thermal Resistance Junction To Case | RθJC | - | - | 1.0 | oC/W |
NOTES: 2. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 20. 3. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss.
Typical Performance Curves Unless Otherwise Specified

TC, CASE TEMPERATURE (oC)
FIGURE 1. DC COLLECTOR CURRENT vs CASE
TEMPERATURE

ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 3. OPERATING FREQUENCY vs COLLECTOR TO
EMITTER CURRENT

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA

VGE, GATE TO EMITTER VOLTAGE (V)
FIGURE 4. SHORT CIRCUIT WITHSTAND TIME
Page 4
Typical Performance Curves Unless Otherwise Specified (Continued)


0 0.5 1.0 1.5 2.0 2.5 3.0
VCE, COLLECTOR TO EMITTER VOLTAGE (V)
VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 6. COLLECTOR TO EMITTER ON-STATE VOLTAGE
FIGURE 5. COLLECTOR TO EMITTER ON-STATE VOLTAGE


ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 8. TURN-OFF ENERGY LOSS vs COLLECTOR TO
FIGURE 7. TURN-ON ENERGY LOSS vs COLLECTOR TO
EMITTER CURRENT
EMITTER CURRENT


0 2 4 6 8 10 12 14
ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 10. TURN-ON RISE TIME vs COLLECTOR TO
FIGURE 9. TURN-ON DELAY TIME vs COLLECTOR TO
EMITTER CURRENT
EMITTER CURRENT
Page 5
Typical Performance Curves Unless Otherwise Specified (Continued)

0 2 4 6 8 10 12 14
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 11. TURN-OFF DELAY TIME vs COLLECTOR TO
EMITTER CURRENT

VGE, GATE TO EMITTER VOLTAGE (V)
FIGURE 13. TRANSFER CHARACTERISTIC

25
125 150
50 75 100
TC, CASE TEMPERATURE (oC)
FIGURE 15. TOTAL SWITCHING LOSS vs CASE
TEMPERATURE

ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 12. FALL TIME vs COLLECTOR TO EMITTER
CURRENT

QG, GATE CHARGE (nC)
FIGURE 14. GATE CHARGE WAVEFORMS

100
10
1000
RG, GATE RESISTANCE (Ω)
FIGURE 16. TOTAL SWITCHING LOSS vs GATE RESISTANCE
Page 6
Typical Performance Curves Unless Otherwise Specified (Continued)

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 17. CAPACITANCE vs COLLECTOR TO EMITTER
VOLTAGE

9 10 11 12 13 14 15 16
VGE, GATE TO EMITTER VOLTAGE (V)
FIGURE 18. COLLECTOR TO EMITTER ON-STATE VOLTAGE
vs GATE TO EMITTER VOLTAGE

t1, RECTANGULAR PULSE DURATION (s)
FIGURE 19. IGBT NORMALIZED TRANSIENT THERMAL RESPONSE, JUNCTION TO CASE
Test Circuit and Waveforms

RHRP660

VDD = 390V
FIGURE 20. INDUCTIVE SWITCHING TEST CIRCUIT
FIGURE 21. SWITCHING TEST WAVEFORMS
Page 7
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:
- Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are
essentially capacitors. Circuits that leave the gate open-circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.
Operating Frequency Information
Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.
fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 21. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON2). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON2 and EOFF are defined in the switching waveforms
shown in Figure 21. EON2 is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).
Page 8
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.
ISOPLANAR™
Stealth™
ACEx™
Power247™
FAST
SuperFET™
ActiveArray™
POWEREDGE™
LittleFET™
FASTr™
MICROCOUPLER™
SuperSOT™-3
Bottomless™
PowerSaver™
FPS™
PowerTrench
SuperSOT™-6
CoolFET™
MicroFET™
FRFET™
QFET
SuperSOT™-8
CROSSVOLT™
MicroPak™
GlobalOptoisolator™
MICROWIRE™
DOME™
GTO™
EcoSPARK™
MSX™
HiSeC™
E2CMOS™
MSXPro™
I2C™
EnSigna™
OCX™
i-Lo™
FACT™
OCXPro™
ImpliedDisconnect™
FACT Quiet Series™
OPTOLOGIC
SyncFET™
QS™
QT Optoelectronics™ TinyLogic
TINYOPTO™
Quiet Series™
TruTranslation™
RapidConfigure™
UHC™
RapidConnect™
UltraFET
µSerDes™
OPTOPLANAR™
SILENT SWITCHER VCX™
Across the board. Around the world.™
SMART START™
PACMAN™
The Power Franchise
SPM™
POP™
Programmable Active Droop™
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.
PRODUCT STATUS DEFINITIONS
Definition of Terms
- A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
| Datasheet Identification | Product Status | Definition |
| Advance Information | Formative or In Design | This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. |
| Preliminary | First Production | This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. |
| No Identification Needed | Full Production | This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. |
| Obsolete | Not In Production | This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. |
Rev. I12