HGTD2N120CNS INTERSIL

Document overview

  • PDF pages: 7

Technical content

Page 1

Data Sheet

13A, 1200V, NPT Series N-Channel IGBT

The HGTD2N120CNS, HGTP2N120CN, and HGT1S2N120CNS are Non-Punch Through (NPT) IGBT designs. They are new members of the MOS gated high voltage switching IGBT family. IGBTs combine the best features of MOSFETs and bipolar transistors. This device has the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor.

The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.

Formerly Developmental Type TA49313.

Ordering Information

PART NUMBER PACKAGE BRAND
HGTP2N120CN TO-220AB 2N120CN
HGTD2N120CNS TO-252AA 2N120C
HGT1S2N120CNS TO-263AB 2N120CN

NOTE: When ordering, use the entire part number. Add the suffix 9A to obtain the TO-263AB and TO-252AA variant in Tape and Reel, e.g., HGT1S2N120CNS9A.

Symbol

C

G

E

HGTD2N120CNS, HGTP2N120CN,

HGT1S2N120CNS

January 2000

File Number 4680.2

Features

  • 13A, 1200V, TC = 25oC
  • 1200V Switching SOA Capability
  • Typical Fall Time. . . . . . . . . . . . . . . . 360ns at TJ = 150oC
  • Short Circuit Rating
  • Low Conduction Loss
  • Avalanche Rated
  • Temperature Compensating SABER™ Model Thermal Impedance SPICE Model www.intersil.com
  • Related Literature - TB334 “Guidelines for Soldering Surface Mount Components to PC Boards”

Packaging

JEDEC TO-220AB

E C

COLLECTOR

G

(FLANGE)

JEDEC TO-252AA

COLLECTOR

(FLANGE)

G E

JEDEC TO-263AB

COLLECTOR

(FLANGE)

G E

INTERSIL CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,364,073

4,417,385

4,430,792

4,443,931

4,466,176

4,516,143

4,532,534

4,587,713

4,598,461

4,605,948

4,620,211

4,631,564

4,639,754

4,639,762

4,641,162

4,644,637

4,682,195

4,684,413

4,694,313

4,717,679

4,743,952

4,783,690

4,794,432

4,801,986

4,803,533

4,809,045

4,809,047

4,810,665

4,823,176

4,837,606

4,860,080

4,883,767

4,888,627

4,890,143

4,901,127

4,904,609

4,933,740

4,963,951

4,969,027

CAUTION: These devices are sensitive to electrostatic discharge; follow proper ESD Handling Procedures.

1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000

SABER™ is a trademark of Analogy, Inc.

Page 2

Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified HGTD2N120CNS HGTP2N120CN, HGT1S2N120CNS UNITS Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BVCES 1200 V Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25 13 A At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110 7 A Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM 20 A Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGES ±20 V Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM ±30 V Switching Safe Operating Area at TJ = 150oC (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . SSOA 13A at 1200V Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 104 W Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.83 W/oC Forward Voltage Avalanche Energy (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAV 18 mJ Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG -55 to 150 oC Maximum Lead Temperature for Soldering Leads at 0.063in (1.6mm) from case for 10s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 300 oC Package Body for 10s, see Tech Brief 334 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tpkg 260 oC Short Circuit Withstand Time (Note 3) at VGE = 15V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC 8 µs CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Pulse width limited by maximum junction temperature. 2. ICE = 3A, L = 4mH. 3. VCE(PK) = 840V, TJ = 125oC, RG = 51Ω.
Electrical Specifications TC = 25oC, Unless Otherwise Specified
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Collector to Emitter Breakdown Voltage BVCES IC = 250µA, VGE = 0V 1200 - - V
Emitter to Collector Breakdown Voltage BVECS IC = 10mA, VGE = 0V 15 - - V
Collector to Emitter Leakage Current ICES VCE = BVCES TC = 25oC - - 100 µA
TC = 125oC - 100 - µA
TC = 150oC - - 1.0 mA
Collector to Emitter Saturation Voltage VCE(SAT) IC = 2.6A, VGE = 15V TC = 25oC - 2.05 2.40 V
TC = 150oC - 2.75 3.50 V
Gate to Emitter Threshold Voltage VGE(TH) IC = 45µA, VCE = VGE 6.4 6.7 - V
Gate to Emitter Leakage Current IGES VGE = ±20V - - ±250 nA
Switching SOA SSOA TJ = 150oC, RG = 51Ω, VGE = 15V, L = 5mH, VCE(PK) = 1200V 13 - - A
Gate to Emitter Plateau Voltage VGEP IC = 2.6A, VCE = 0.5 BVCES - 10.2 - V
On-State Gate Charge QG(ON) IC = 2.6A, VCE = 0.5 BVCES VGE = 15V - 30 36 nC
VGE = 20V - 36 43 nC

Page 3

Electrical Specifications TC = 25oC, Unless Otherwise Specified (Continued)
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 25oC ICE = 2.6A VCE = 0.8 BVCES VGE = 15V RG = 51Ω L = 5mH Test Circuit (Figure 18) - 25 30 ns
Current Rise Time trI - 11 15 ns
Current Turn-Off Delay Time td(OFF)I - 205 220 ns
Current Fall Time tfI - 260 320 ns
Turn-On Energy (Note 4) EON1 - 96 - µJ
Turn-On Energy (Note 4) EON2 - 425 590 µJ
Turn-Off Energy (Note 5) EOFF - 355 390 µJ
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 150oC, ICE = 2.6A, VCE = 0.8 BVCES, VGE = 15V, RG = 51Ω, L = 5mH, Test Circuit (Figure 18) - 21 25 ns
Current Rise Time trI - 11 15 ns
Current Turn-Off Delay Time td(OFF)I - 225 240 ns
Current Fall Time tfI - 360 420 ns
Turn-On Energy (Note 4) EON1 - 96 - µJ
Turn-On Energy (Note 4) EON2 - 800 1100 µJ
Turn-Off Energy (Note 5) EOFF - 530 580 µJ
Thermal Resistance Junction To Case RθJC - - 1.20 oC/W
NOTES: 4. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 18. 5. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss. Typical Performance Curves Unless Otherwise Specified 14 16 (A) VGE = 15V TJ = 150oC, RG = 51Ω, VGE = 15V, L = 5mH CURRENT (A) 12 14 CURRENT 12 10 EMITTER 10 8 COLLECTOR 8 6 TO 6 COLLECTOR 4 4 DC 2 2 ICE, ICE, 0 0 25 50 75 100 125 150 0 200 400 600 800 1000 1200 1400 TC, CASE TEMPERATURE (oC) VCE, COLLECTOR TO EMITTER VOLTAGE (V) FIGURE 1. DC COLLECTOR CURRENT vs CASE FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA TEMPERATURE

Page 4

PDF page 4 diagram

Page 5

PDF page 5 diagram

Page 6

PDF page 6 diagram

Page 7

Handling Precautions for IGBTs

Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:

  1. Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are

essentially capacitors. Circuits that leave the gate open-circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required, an external Zener is recommended.

Operating Frequency Information

Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.

fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 19. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.

fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON2). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON2 and EOFF are defined in the switching waveforms shown in Figure 19. EON2 is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).

ECCOSORBD™ is a trademark of Emerson and Cumming, Inc.