HGTD7N60A4S INTERSIL

Document overview

  • PDF pages: 11

Technical content

Page 1

HGTD7N60A4S, HGT1S7N60A4S, HGTG7N60A4,

TM

Data Sheet

600V, SMPS Series N-Channel IGBT

The HGTD7N60A4S, HGT1S7N60A4S, HGTG7N60A4 and HGTP7N60A4 are MOS gated high voltage switching devices combining the best features of MOSFETs and bipolar transistors. These devices have the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between 25oC and 150oC.

This IGBT is ideal for many high voltage switching applications operating at high frequencies where low conduction losses are essential. This device has been optimized for high frequency switch mode power supplies.

Formerly Developmental Type TA49331.

Ordering Information

PART NUMBER PACKAGE BRAND
HGTD7N60A4S TO-252AA 7N60A4
HGT1S7N60A4S TO-263AB 7N60A4
HGTG7N60A4 TO-247 7N60A4
HGTP7N60A4 TO-220AB 7N60A4

NOTE: When ordering, use the entire part number. Add the suffix 9A to obtain the TO-252AA and TO-263AB variant in tape and reel, e.g., HGTD7N60A4S9A.

Packaging

JEDEC STYLE TO-247

E C G

COLLECTOR

(FLANGE)

JEDEC TO-252AA

COLLECTOR

G

(FLANGE)

E

HGTP7N60A4

June 2000

File Number 4826.2

Features

  • >100kHz Operation at 390V, 7A
  • 200kHz Operation at 390V, 5A
  • 600V Switching SOA Capability
  • Typical Fall Time. . . . . . . . . . . . . . . . . . . .75ns at TJ = 125oC
  • Low Conduction Loss
  • Temperature Compensating SABER™ Model www.intersil.com

Symbol

C

G

E

JEDEC TO-220AB

E C G

COLLECTOR

(FLANGE)

JEDEC TO-263AB

G

COLLECTOR

E

(FLANGE)

INTERSIL CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,364,073

4,417,385

4,430,792

4,443,931

4,466,176

4,516,143

4,532,534

4,587,713

4,598,461

4,605,948

4,620,211

4,631,564

4,639,754

4,639,762

4,641,162

4,644,637

4,682,195

4,684,413

4,694,313

4,717,679

4,743,952

4,783,690

4,794,432

4,801,986

4,803,533

4,809,045

4,809,047

4,810,665

4,823,176

4,837,606

4,860,080

4,883,767

4,888,627

4,890,143

4,901,127

4,904,609

4,933,740

4,963,951

4,969,027

CAUTION: These devices are sensitive to electrostatic discharge; follow proper ESD Handling Procedures.

2-1

SABER™ is a trademark of Analogy, Inc. | 1-888-INTERSIL or 321-724-7143

Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000

Page 2

Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified ALL TYPES UNITS Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BVCES 600 V Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25 34 A At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110 14 A Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ICM 56 A Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGES ±20 V Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM ±30 V Switching Safe Operating Area at TJ = 150oC, Figure 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .SSOA 35A at 600V Single Pulse Avalanche Energy at TC = 25oC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAS 25mJ at 7A Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 125 W Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 W/oC Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG -55 to 150 oC Maximum Lead Temperature for Soldering Leads at 0.063in (1.6mm) from Case for 10s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TL 300 oC Package Body for 10s, See Tech Brief 334 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TPKG 260 oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. Pulse width limited by maximum junction temperature.
Electrical Specifications TJ = 25oC, Unless Otherwise Specified
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Collector to Emitter Breakdown Voltage BVCES IC = 250µA, VGE = 0V 600 - - V
Emitter to Collector Breakdown Voltage BVECS IC = 10mA, VGE = 0V 20 - - V
Collector to Emitter Leakage Current ICES VCE = 600V TJ = 25oC - - 250 µA
TJ = 125oC - - 2 mA
Collector to Emitter Saturation Voltage VCE(SAT) IC = 7A, VGE = 15V TJ = 25oC - 1.9 2.7 V
TJ = 125oC - 1.6 2.2 V
Gate to Emitter Threshold Voltage VGE(TH) IC = 250µA, VCE = 600V 4.5 5.9 7.0 V
Gate to Emitter Leakage Current IGES VGE = ±20V - - ±250 nA
Switching SOA SSOA TJ = 150oC, RG = 25Ω, VGE = 15V L = 100µH, VCE = 600V 35 - - A
Pulsed Avalanche Energy EAS ICE = 7A, L = 500µH 25 - - mJ
Gate to Emitter Plateau Voltage VGEP IC = 7A, VCE = 300V - 9.0 - V
On-State Gate Charge Qg(ON) IC = 7A, VCE = 300V VGE = 15V - 37 45 nC
VGE = 20V - 48 60 nC
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 25oC ICE = 7A VCE = 390V VGE = 15V RG = 25Ω L = 1mH Test Circuit (Figure 20) - 11 - ns
Current Rise Time trI - 11 - ns
Current Turn-Off Delay Time td(OFF)I - 100 - ns
Current Fall Time tfI - 45 - ns
Turn-On Energy (Note 2) EON1 - 55 - µJ
Turn-On Energy (Note 2) EON2 - 120 150 µJ
Turn-Off Energy (Note 3) EOFF - 60 75 µJ

2-2

Page 3

Electrical Specifications TJ = 25oC, Unless Otherwise Specified (Continued)
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 125oC ICE = 7A VCE = 390V VGE = 15V RG = 25Ω L = 1mH Test Circuit (Figure 20) - 10 - ns
Current Rise Time trI - 7 - ns
Current Turn-Off Delay Time td(OFF)I - 130 150 ns
Current Fall Time tfI - 75 85 ns
Turn-On Energy (Note 2) EON1 - 50 - µJ
Turn-On Energy (Note 2) EON2 - 200 215 µJ
Turn-Off Energy (Note 3) EOFF - 125 170 µJ
Thermal Resistance Junction To Case RθJC - - 1.0 oC/W
NOTES: 2. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 20. 3. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss. Typical Performance Curves Unless Otherwise Specified 35 40 (A) VGE = 15V TJ = 150oC, RG = 25Ω, VGE = 15V, L = 100µH (A) CURRENT 30 CURRENT 30 25 EMITTER 20 COLLECTOR 20 15 TO COLLECTOR 10 10 DC 5 ICE, ICE, 0 0 25 50 75 100 125 150 0 100 200 300 400 500 600 700 TC, CASE TEMPERATURE (oC) VCE, COLLECTOR TO EMITTER VOLTAGE (V) FIGURE 1. DC COLLECTOR CURRENT vs CASE FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA TEMPERATURE 500 7T 5C oC V 1G 5VE 16 VCE = 390V, RG = 25Ω, TJ = 125oC 140 (kHz) TIME (µs) CURRENT (A) FREQUENCY 14 120 WITHSTAND 200 ISC 12 100 CIRCUIT OPERATING 100 fMAX1 = 0.05 / (td(OFF)I + td(ON)I) 10 80 CIRCUIT fMAX2 = (PD - PC) / (EON2 + EOFF) SHORT PC = CONDUCTION DISSIPATION 8 60 (DUTY FACTOR = 50%) R TØ J =C = 51 o.0 Co C R/ GW , S 2E 5E ,N LO =T E 2S 6 tSC 40 fMAX, SHORT PEAK J 1 2 , = Ω mH, VCE = 390V 30 tSC, ISC, 1 5 10 20 4 20 10 11 12 13 14 15 ICE, COLLECTOR TO EMITTER CURRENT (A) VGE, GATE TO EMITTER VOLTAGE (V) FIGURE 3. OPERATING FREQUENCY vs COLLECTOR TO FIGURE 4. SHORT CIRCUIT WITHSTAND TIME EMITTER CURRENT

2-3

Page 4

PDF page 4 diagram

Page 5

PDF page 5 diagram

Page 6

PDF page 6 diagram

Page 7

Handling Precautions for IGBTs

Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:

  1. Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are

essentially capacitors. Circuits that leave the gate open-circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.

2-7

Operating Frequency Information

Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.

fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 21. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON2). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON2 and EOFF are defined in the switching waveforms

shown in Figure 21. EON2 is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).

ECCOSORBD™ is a trademark of Emerson and Cumming, Inc.

Page 8

PDF page 8 diagram
PDF page 8 diagram
SYMBOL INCHES MILLIMETERS NOTES
MIN MAX MIN MAX
A 0.180 0.190 4.58 4.82 -
b 0.046 0.051 1.17 1.29 2, 3
b1 0.060 0.070 1.53 1.77 1, 2
b2 0.095 0.105 2.42 2.66 1, 2
c 0.020 0.026 0.51 0.66 1, 2, 3
D 0.800 0.820 20.32 20.82 -
E 0.605 0.625 15.37 15.87 -
e 0.219 TYP 5.56 TYP 4
e1 0.438 BSC 11.12 BSC 4
J1 0.090 0.105 2.29 2.66 5
L 0.620 0.640 15.75 16.25 -
L1 0.145 0.155 3.69 3.93 1
ØP 0.138 0.144 3.51 3.65 -
Q 0.210 0.220 5.34 5.58 -
ØR 0.195 0.205 4.96 5.20 -
ØS 0.260 0.270 6.61 6.85 -
PDF page 8 diagram

Page 9

PDF page 9 diagram
PDF page 9 diagram
SYMBOL INCHES MILLIMETERS NOTES
MIN MAX MIN MAX
A 0.086 0.094 2.19 2.38 -
A1 0.018 0.022 0.46 0.55 4, 5
b 0.028 0.032 0.72 0.81 4, 5
b1 0.033 0.045 0.84 1.14 4
b2 0.205 0.215 5.21 5.46 4, 5
b3 0.190 - 4.83 - 2
c 0.018 0.022 0.46 0.55 4, 5
D 0.270 0.295 6.86 7.49 -
E 0.250 0.265 6.35 6.73 -
e 0.090 TYP 2.28 TYP 7
e1 0.180 BSC 4.57 BSC 7
H1 0.035 0.045 0.89 1.14 -
J1 0.040 0.045 1.02 1.14 -
L 0.100 0.115 2.54 2.92 -
L1 0.020 - 0.51 - 4, 6
L2 0.025 0.040 0.64 1.01 3
L3 0.170 - 4.32 - 2
PDF page 9 diagram

Page 10

TO-263AB

SURFACE MOUNT JEDEC TO-263AB PLASTIC PACKAGE

PDF page 10 diagram
SYMBOL INCHES MILLIMETERS NOTES
MIN MAX MIN MAX
A 0.170 0.180 4.32 4.57 -
A1 0.048 0.052 1.22 1.32 4, 5
b 0.030 0.034 0.77 0.86 4, 5
b1 0.045 0.055 1.15 1.39 4, 5
b2 0.310 - 7.88 - 2
c 0.018 0.022 0.46 0.55 4, 5
D 0.405 0.425 10.29 10.79 -
E 0.395 0.405 10.04 10.28 -
e 0.100 TYP 2.54 TYP 7
e1 0.200 BSC 5.08 BSC 7
H1 0.045 0.055 1.15 1.39 -
J1 0.095 0.105 2.42 2.66 -
L 0.175 0.195 4.45 4.95 -
L1 0.090 0.110 2.29 2.79 4, 6
L2 0.050 0.070 1.27 1.77 3
L3 0.315 - 8.01 - 2
PDF page 10 diagram

Page 11

TO-220AB

3 LEAD JEDEC TO-220AB PLASTIC PACKAGE

A

SYMBOL INCHES MILLIMETERS NOTES
MIN MAX MIN MAX
A 0.170 0.180 4.32 4.57 -
A1 0.048 0.052 1.22 1.32 -
b 0.030 0.034 0.77 0.86 3, 4
b1 0.045 0.055 1.15 1.39 2, 3
c 0.014 0.019 0.36 0.48 2, 3, 4
D 0.590 0.610 14.99 15.49 -
D1 - 0.160 - 4.06 -
E 0.395 0.410 10.04 10.41 -
E1 - 0.030 - 0.76 -
e 0.100 TYP 2.54 TYP 5
e1 0.200 BSC 5.08 BSC 5
H1 0.235 0.255 5.97 6.47 -
J1 0.100 0.110 2.54 2.79 6
L 0.530 0.550 13.47 13.97 -
L1 0.130 0.150 3.31 3.81 2
ØP 0.149 0.153 3.79 3.88 -
Q 0.102 0.112 2.60 2.84 -

E

ØP

A1

Q

H1

TERM. 4

D

45o

E1

D1

L1

b1

b

L

c

60o 1 2 3 e

J1

e1

NOTES: 1. These dimensions are within allowable dimensions of Rev. J of JEDEC TO-220AB outline dated 3-24-87. 2. Lead dimension and finish uncontrolled in L1. 3. Lead dimension (without solder). 4. Add typically 0.002 inches (0.05mm) for solder coating. 5. Position of lead to be measured 0.250 inches (6.35mm) from bottom of dimension D. 6. Position of lead to be measured 0.100 inches (2.54mm) from bottom of dimension D. 7. Controlling dimension: Inch. 8. Revision 2 dated 7-97.

All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see web site www.intersil.com

Sales Office Headquarters

NORTH AMERICA

EUROPE

Intersil Corporation

Intersil SA

P. O. Box 883, Mail Stop 53-204

Mercure Center

Melbourne, FL 32902

100, Rue de la Fusee

TEL: (321) 724-7000

1130 Brussels, Belgium

FAX: (321) 724-7240

TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05

2-11

ASIA

Intersil Ltd. 8F-2, 96, Sec. 1, Chien-kuo North, Taipei, Taiwan 104 Republic of China TEL: 886-2-2515-8508 FAX: 886-2-2515-8369