HGTG40N60A4 FAIRCHILD

Document overview

  • PDF pages: 8

Technical content

Page 1

Data Sheet

600V, SMPS Series N-Channel IGBT

The HGTG40N60A4 is a MOS gated high voltage switching device combining the best features of a MOSFET and a bipolar transistor. This device has the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between 25oC and 150oC. This IGBT is ideal for many high voltage switching applications operating at high frequencies where low conduction losses are essential. This device has been optimized for high frequency switch mode power supplies.

Formerly Developmental Type TA49347.

Ordering Information

PART NUMBER PACKAGE BRAND
HGTG40N60A4 TO-247 40N60A4

NOTE: When ordering, use the entire part number.

Symbol

C

G

E

August 2003

File Number

Features

  • 100kHz Operation At 390V, 40A
  • 200kHz Operation At 390V, 20A
  • 600V Switching SOA Capability
  • Typical Fall Time. . . . . . . . . . . . . . . . . . .55ns at TJ = 125o
  • Low Conduction Loss

Packaging

JEDEC STYLE TO-247

E

PDF page 1 diagram

FAIRCHILD CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,364,073

4,417,385

4,430,792

4,443,931

4,466,176

4,516,143

4,532,534

4,587,713

4,598,461

4,605,948

4,620,211

4,631,564

4,639,754

4,639,762

4,641,162

4,644,637

4,682,195

4,684,413

4,694,313

4,717,679

4,743,952

4,783,690

4,794,432

4,801,986

4,803,533

4,809,045

4,809,047

4,810,665

4,823,176

4,837,606

4,860,080

4,883,767

4,888,627

4,890,143

4,901,127

4,904,609

4,933,740

4,963,951

4,969,027

Page 2

Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified

UNITS

600

V

Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BVCES Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25

75

A

At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110

63

A

300

A

Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGES

±20

V

±30

V

Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGEM Switching Safe Operating Area at TJ = 150oC, Figure 2 . . . . . . . . . . . . . . . . . . . . . . . . SSOA

200A at 600V

Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD

625

W

Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

W/oC

5

oC

Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG

-55 to 150

oC

260

Maximum Lead Temperature for Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE: 1. Pulse width limited by maximum junction temperature.

TJ = 25oC, Unless Otherwise Specified

Electrical Specifications

PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Collector to Emitter Breakdown Voltage BVCES IC = 250µA, VGE = 0V 600 - - V
Emitter to Collector Breakdown Voltage BVECS IC = -10mA, VGE = 0V 20 - -
Collector to Emitter Leakage Current ICES VCE = BVCES TJ = 25oC - - 250 µA
TJ = 125oC - - 3.0 mA
Collector to Emitter Saturation Voltage VCE(SAT) IC = 40A, VGE = 15V TJ = 25oC - 1.7 2.7 V
TJ = 125oC - 1.5 2.0 V
Gate to Emitter Threshold Voltage VGE(TH) IC = 250µA, VCE = VGE 4.5 5.6 7 V
Gate to Emitter Leakage Current IGES VGE = ±20V - - ±250 nA
Switching SOA SSOA TJ = 150oC, RG = 2.2Ω, VGE = 15V L = 100µH, VCE = 600V 200 - - A
Gate to Emitter Plateau Voltage VGEP IC = 40A, VCE = 0.5 BVCES - 8.5 - V
On-State Gate Charge Qg(ON) IC = 40A, VCE = 0.5 BVCES VGE = 15V - 350 405 nC
VGE = 20V - 450 520 nC
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 25oC ICE = 40A VCE = 0.65 BVCES VGE = 15V RG = 2.2Ω L = 200µH Test Circuit (Figure 20) - 25 - ns
Current Rise Time trI - 18 - ns
Current Turn-Off Delay Time td(OFF)I - 145 - ns
Current Fall Time tfI - 35 - ns
Turn-On Energy (Note 3) EON1 - 400 - µJ
Turn-On Energy (Note 3) EON2 - 850 - µJ
Turn-Off Energy (Note 2) EOFF - 370 - µJ

Page 3

TJ = 25oC, Unless Otherwise Specified (Continued)

Electrical Specifications

PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 125oC ICE = 40A VCE = 0.65 BVCES VGE = 15V RG = 2.2Ω L = 200µH Test Circuit (Figure 20) - 27 - ns
Current Rise Time trI - 20 - ns
Current Turn-Off Delay Time td(OFF)I - 185 225 ns
Current Fall Time tfI - 55 95 ns
Turn-On Energy (Note 3) EON1 - 400 - µJ
Turn-On Energy (Note 3) EON2 - 1220 1400 µJ
Turn-Off Energy (Note 2) EOFF - 700 800 µJ
Thermal Resistance Junction To Case RθJC - - 0.2 oC/W

NOTES: 2. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss. 3. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 20.

Typical Performance Curves Unless Otherwise Specified

PDF page 3 diagram

25 50 75 100 125 150

TC, CASE TEMPERATURE (oC)

FIGURE 1. DC COLLECTOR CURRENT vs CASE

TEMPERATURE

PDF page 3 diagram

VCE, COLLECTOR TO EMITTER VOLTAGE (V)

FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA

Page 4

Typical Performance Curves Unless Otherwise Specified (Continued)

PDF page 4 diagram
PDF page 4 diagram

3

10

40 70

ICE, COLLECTOR TO EMITTER CURRENT (A)

VGE, GATE TO EMITTER VOLTAGE (V)

FIGURE 3. OPERATING FREQUENCY vs COLLECTOR TO

FIGURE 4. SHORT CIRCUIT WITHSTAND TIME

EMITTER CURRENT

PDF page 4 diagram
PDF page 4 diagram

VCE, COLLECTOR TO EMITTER VOLTAGE (V)

VCE, COLLECTOR TO EMITTER VOLTAGE (V)

FIGURE 6. COLLECTOR TO EMITTER ON-STATE VOLTAGE

FIGURE 5. COLLECTOR TO EMITTER ON-STATE VOLTAGE

PDF page 4 diagram
PDF page 4 diagram

0 10 20 30 40 50 60 70 80

ICE, COLLECTOR TO EMITTER CURRENT (A)

ICE, COLLECTOR TO EMITTER CURRENT (A)

FIGURE 8. TURN-OFF ENERGY LOSS vs COLLECTOR TO

FIGURE 7. TURN-ON ENERGY LOSS vs COLLECTOR TO

EMITTER CURRENT

EMITTER CURRENT

Page 5

Typical Performance Curves Unless Otherwise Specified (Continued)

PDF page 5 diagram
PDF page 5 diagram

ICE, COLLECTOR TO EMITTER CURRENT (A)

ICE, COLLECTOR TO EMITTER CURRENT (A)

FIGURE 10. TURN-ON RISE TIME vs COLLECTOR TO

FIGURE 9. TURN-ON DELAY TIME vs COLLECTOR TO

EMITTER CURRENT

EMITTER CURRENT

PDF page 5 diagram
PDF page 5 diagram

ICE, COLLECTOR TO EMITTER CURRENT (A)

ICE, COLLECTOR TO EMITTER CURRENT (A)

FIGURE 12. FALL TIME vs COLLECTOR TO EMITTER

FIGURE 11. TURN-OFF DELAY TIME vs COLLECTOR TO

EMITTER CURRENT

CURRENT

PDF page 5 diagram
PDF page 5 diagram

VGE, GATE TO EMITTER VOLTAGE (V)

QG, GATE CHARGE (nC)

FIGURE 13. TRANSFER CHARACTERISTIC

FIGURE 14. GATE CHARGE WAVEFORMS

Page 6

Typical Performance Curves Unless Otherwise Specified (Continued)

PDF page 6 diagram

TC, CASE TEMPERATURE (oC)

FIGURE 15. TOTAL SWITCHING LOSS vs CASE

TEMPERATURE

PDF page 6 diagram

VCE, COLLECTOR TO EMITTER VOLTAGE (V)

FIGURE 17. CAPACITANCE vs COLLECTOR TO EMITTER

VOLTAGE

PDF page 6 diagram

RG, GATE RESISTANCE (Ω)

FIGURE 16. TOTAL SWITCHING LOSS vs GATE RESISTANCE

PDF page 6 diagram

VGE, GATE TO EMITTER VOLTAGE (V)

FIGURE 18. COLLECTOR TO EMITTER ON-STATE VOLTAGE vs

GATE TO EMITTER VOLTAGE

PDF page 6 diagram

t1, RECTANGULAR PULSE DURATION (s)

FIGURE 19. NORMALIZED TRANSIENT THERMAL RESPONSE, JUNCTION TO CASE

Page 7

Test Circuit and Waveforms

PDF page 7 diagram

VDD = 390V

FIGURE 20. INDUCTIVE SWITCHING TEST CIRCUIT

Handling Precautions for IGBTs

Insulated Gate Bipolar Transistors are susceptible to gateinsulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:

  1. Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are

essentially capacitors. Circuits that leave the gate opencircuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.

90% 10%
EO EOFF 90% 10% td(OFF)I tfI N2 trI td(ON)I

VGE

VCE

ICE

FIGURE 21. SWITCHING TEST WAVEFORMS

Operating Frequency Information

Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.

fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 21. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.

fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON2). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON2 and EOFF are defined in the switching waveforms shown in Figure 21. EON2 is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).

Page 8

TRADEMARKS

The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.

Power247™

FACT Quiet Series™ LittleFET™

SuperSOT™-6

ACEx™

FAST®

PowerTrench®

MICROCOUPLER™

ActiveArray™

FASTr™

MicroFET™

Bottomless™

FRFET™

MicroPak™

CoolFET™ CROSSVOLT™ GlobalOptoisolator™ MICROWIRE™

GTO™

MSX™

DOME™

HiSeC™

MSXPro™

EcoSPARK™ E2CMOS™

I2C™

OCX™

EnSigna™

ImpliedDisconnect™ OCXPro™

OPTOLOGIC®

FACT™

ISOPLANAR™

Across the board. Around the world.™ OPTOPLANAR™ The Power Franchise™

PACMAN™

Programmable Active Droop™

POP™

DISCLAIMER

SuperSOT™-8

QFET®

SyncFET™ TinyLogic®

QS™ QT Optoelectronics™ TINYOPTO™

TruTranslation™

Quiet Series™

UHC™

RapidConfigure™

UltraFET®

RapidConnect™ SILENT SWITCHER® VCX™ SMART START™ SPM™ Stealth™ SuperSOT™-3

FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.

As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.

PRODUCT STATUS DEFINITIONS

Definition of Terms

  1. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Datasheet Identification Product Status Definition
Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice.
Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only.

Rev. I5