HGTG30N60C3D HARRIS
Document overview
- PDF pages: 8
Technical content
Page 1
S E M I C O N D U C T O R HGTG30N60C3D
August 1995
Features
- 63A, 600V at TC = +25oC
- Typical Fall Time - 230ns at TJ = +150oC
- Short Circuit Rating
- Low Conduction Loss
- Hyperfast Anti-Parallel Diode
Description
The HGTG30N60C3D is a MOS gated high voltage switching device combining the best features of MOSFETs and bipolar transistors. The device has the high input impedance of a MOS- FET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between +25oC and +150oC. The IGBT used is the development type TA49051. The diode used in anti-parallel with the IGBT is the development type TA49053. The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential.
PACKAGING AVAILABILITY
| PART NUMBER | PACKAGE | BRAND |
|---|---|---|
| HGTG30N60C3D | TO-247 | G30N60C3D |
NOTE: When ordering, use the entire part number. Formerly Developmental Type TA49014.
63A, 600V, UFS Series N-Channel IGBT
with Anti-Parallel Hyperfast Diode
Package
JEDEC STYLE TO-247
E C G
Terminal Diagram
N-CHANNEL ENHANCEMENT MODE
C
G
E
Absolute Maximum Ratings TC = +25oC, Unless Otherwise Specified
UNITS
Collector-Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BVCES
600
V
Collector Current Continuous At TC = +25oC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25
63
A
At TC = +110oC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110
30
A
Average Diode Forward Current at +110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I(AVG)
25
A
Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM
252
A
Gate-Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGES
±20
V
Gate-Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM
±30
V
Switching Safe Operating Area at TJ = +150oC . . . . . . . . . . . . . . . . . . . . . . . . . . . .SSOA
60A at 600V
Power Dissipation Total at TC = +25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD
208
W
Power Dissipation Derating TC > +25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W/oC
1.67
Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . .TJ, TSTG
oC
-40 to +150
Maximum Lead Temperature for Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TL
oC
260
Short Circuit Withstand Time (Note 2) at VGE = 15V . . . . . . . . . . . . . . . . . . . . . . . . . . tSC
4
µs
Short Circuit Withstand Time (Note 2) at VGE = 10V . . . . . . . . . . . . . . . . . . . . . . . . . . tSC
15
µs
NOTE: 1. Repetitive Rating: Pulse width limited by maximum junction temperature. 2. VCE(PK) = 360V, TJ = +125oC, RGE = 25Ω.
HARRIS SEMICONDUCTOR IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS:
4,364,073
4,417,385
4,430,792
4,443,931
4,466,176
4,516,143
4,532,534
4,567,641
4,587,713
4,598,461
4,605,948
4,618,872
4,620,211
4,631,564
4,639,754
4,639,762
4,641,162
4,644,637
4,682,195
4,684,413
4,694,313
4,717,679
4,743,952
4,783,690
4,794,432
4,801,986
4,803,533
4,809,045
4,809,047
4,810,665
4,823,176
4,837,606
4,860,080
4,883,767
4,888,627
4,890,143
4,901,127
4,904,609
4,933,740
4,963,951
4,969,027
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper ESD Handling Procedures.
File Number 4041
Copyright © Harris Corporation 1995
Page 2
Specifications HGTG30N60C3D
Electrical Specifications TC = +25oC, Unless Otherwise Specified
| PARAMETERS | SYMBOL | TEST CONDITIONS | LIMITS | UNITS | |||
|---|---|---|---|---|---|---|---|
| MIN | TYP | MAX | |||||
| Collector-Emitter Breakdown Voltage | BV CES | I = 250µA, V = 0V C GE | 600 | - | - | V | |
| Emitter-Collector Breakdown Voltage | BV ECS | I = 10mA, V = 0V C GE | 15 | 25 | - | V | |
| Collector-Emitter Leakage Current | I CES | V = BV CE CES | T = +25oC C | - | - | 250 | µA |
| V = BV CE CES | T = +150oC C | - | - | 3.0 | mA | ||
| Collector-Emitter Saturation Voltage | V CE(SAT) | I = I , C C110 V = 15V GE | T = +25oC C | - | 1.5 | 1.8 | V |
| T = +150oC C | - | 1.7 | 2.0 | V | |||
| Gate-Emitter Threshold Voltage | V GE(TH) | I = 250µA, C V = V CE GE | T = +25oC C | 3.0 | 5.2 | 6.0 | V |
| Gate-Emitter Leakage Current | I GES | V = ±20V GE | - | - | ±100 | nA | |
| Switching SOA | SSOA | T = +150oC, J V = 15V, GE R = 3Ω, G L = 100µH | V = 480V CE(PK) | 200 | - | - | A |
| V = 600V CE(PK) | 60 | - | - | A | |||
| Gate-Emitter Plateau Voltage | V GEP | I = I , V = 0.5 BV C C110 CE CES | - | 8.1 | - | V | |
| On-State Gate Charge | Q G(ON) | I = I , C C110 V = 0.5 BV CE CES | V = 15V GE | - | 162 | 180 | nC |
| V = 20V GE | - | 216 | 250 | nC | |||
| Current Turn-On Delay Time | t D(ON)I | T = +150oC, J I = I CE C110, V = 0.8 BV CE(PK) CES, V = 15V, GE R = 3Ω, G L = 100µH | - | 40 | - | ns | |
| Current Rise Time | t RI | - | 45 | - | ns | ||
| Current Turn-Off Delay Time | t D(OFF)I | - | 320 | 400 | ns | ||
| Current Fall Time | t FI | - | 230 | 275 | ns | ||
| Turn-On Energy | E ON | - | 1050 | - | µJ | ||
| Turn-Off Energy (Note 1) | E OFF | - | 2500 | - | µJ | ||
| Diode Forward Voltage | V EC | I = 30A EC | - | 1.75 | 2.2 | V | |
| Diode Reverse Recovery Time | t RR | I = 30A, dI EC/dt = 100A/µs EC | - | 52 | 60 | ns | |
| I = 1.0A, dI /dt = 100A/µs EC EC | - | 42 | 50 | ns | |||
| Thermal Resistance | R θJC | IGBT | - | - | 0.6 | oC/W | |
| Diode | - | - | 1.3 | oC/W | |||

Page 3

Page 4

Page 5

Page 6

Page 7
Operating Frequency Information
Operating frequency information for a typical device (Figure 13) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 4, 7, 8, 11 and 12. The operating frequency plot (Figure 13) of a typical device shows fMAX1 or fMAX2 whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature. fMAX1 is defined by fMAX1 = 0.05/(tD(OFF)I + tD(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are
possible. tD(OFF)I and tD(ON)I are defined in Figure 21. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJMAX. tD(OFF)I is important when controlling output ripple under a lightly loaded condition. fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON). The allowable dissipation (PD) is defined by PD = (TJMAX - TC)/ RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 13) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON and EOFF are defined in the switching waveforms shown in Figure 21. EON is the integral of the instantaneous
power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss during turn-off. All tail losses are included in the calculation for EOFF; i.e. the collector current equals zero (ICE = 0).
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to gateinsulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken: 1. Prior to assembly into a circuit, all leads should be kept
shorted together either by the use of metal shorting springs or by the insertion into conductive material such as †“ECCOSORBD LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are essentially capacitors. Circuits that leave the gate open-circuited
or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic zener diode from gate to emitter. If gate protection is required an external zener is recommended.
†Trademark Emerson and Cumming, Inc.
Page 8
Packaging
A
E
ØP ØS
Q
ØR
D
L1
b1 b2
L
c b
3
3 2 1
2
J1
e
BACK VIEW
e1
LEAD NO. 1 - GATE
LEAD NO. 2 - COLLECTOR
LEAD NO. 3 - EMITTER
TERM. 4
- COLLECTOR
TO-247
TERM. 4
3 LEAD JEDEC STYLE TO-247 PLASTIC PACKAGE
| SYMBOL | INCHES | MILLIMETERS | NOTES | ||
|---|---|---|---|---|---|
| MIN | MAX | MIN | MAX | ||
| A | 0.180 | 0.190 | 4.58 | 4.82 | - |
| b | 0.046 | 0.051 | 1.17 | 1.29 | 2, 3 |
| b 1 | 0.060 | 0.070 | 1.53 | 1.77 | 1, 2 |
| b 2 | 0.095 | 0.105 | 2.42 | 2.66 | 1, 2 |
| c | 0.020 | 0.026 | 0.51 | 0.66 | 1, 2, 3 |
| D | 0.800 | 0.820 | 20.32 | 20.82 | - |
| E | 0.605 | 0.625 | 15.37 | 15.87 | - |
| e | 0.219 TYP | 5.56 TYP | 4 | ||
| e 1 | 0.438 BSC | 11.12 BSC | 4 | ||
| J 1 | 0.090 | 0.105 | 2.29 | 2.66 | 5 |
| L | 0.620 | 0.640 | 15.75 | 16.25 | - |
| L 1 | 0.145 | 0.155 | 3.69 | 3.93 | 1 |
| ØP | 0.138 | 0.144 | 3.51 | 3.65 | - |
| Q | 0.210 | 0.220 | 5.34 | 5.58 | - |
| ØR | 0.195 | 0.205 | 4.96 | 5.20 | - |
| ØS | 0.260 | 0.270 | 6.61 | 6.85 | - |
1
NOTES: 1. Lead dimension and finish uncontrolled in L1. 2. Lead dimension (without solder). 3. Add typically 0.002 inches (0.05mm) for solder coating. 4. Position of lead to be measured 0.250 inches (6.35mm) from bottom of dimension D. 5. Position of lead to be measured 0.100 inches (2.54mm) from bottom of dimension D. 6. Controlling dimension: Inch. 7. Revision 1 dated 1-93.
All Harris Semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Harris Semiconductor products are sold by description only. Harris Semiconductor reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Harris is believed to be accurate and reliable. However, no responsibility is assumed by Harris or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Harris or its subsidiaries.
Sales Office Headquarters
For general information regarding Harris Semiconductor and its products, call 1-800-4-HARRIS
UNITED STATES
EUROPE
Harris Semiconductor P. O. Box 883, Mail Stop 53-210 Melbourne, FL 32902 TEL: 1-800-442-7747 (407) 729-4984 FAX: (407) 729-5321
ASIA
Harris Semiconductor
Harris Semiconductor PTE Ltd.
Mercure Center
No. 1 Tannery Road
100, Rue de la Fusee
Cencon 1, #09-01
1130 Brussels, Belgium
Singapore 1334
TEL: (32) 2.724.2111
TEL: (65) 748-4200
FAX: (32) 2.724.22.05
FAX: (65) 748-0400