HGTG30N60B3 INTERSIL

Document overview

  • PDF pages: 7

Technical content

Page 1

Data Sheet

60A, 600V, UFS Series N-Channel IGBT

The HGTG30N60B3 is a MOS gated high voltage switching device combining the best features of MOSFETs and bipolar transistors. This device has the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between 25oC and 150oC.

The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.

Formerly Developmental Type TA49170.

Ordering Information

PART NUMBER PACKAGE BRAND
HGTG30N60B3 TO-247 G30N60B3

NOTE: When ordering, use the entire part number.

Symbol

C

G

E

January 2000

File Number 4444.2

Features

  • 60A, 600V, TC = 25oC
  • 600V Switching SOA Capability
  • Typical Fall Time. . . . . . . . . . . . . . . . . 90ns at TJ = 150oC
  • Short Circuit Rating
  • Low Conduction Loss

Packaging

JEDEC STYLE TO-247

E C G

INTERSIL CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,364,073

4,417,385

4,430,792

4,443,931

4,466,176

4,516,143

4,532,534

4,587,713

4,598,461

4,605,948

4,620,211

4,631,564

4,639,754

4,639,762

4,641,162

4,644,637

4,682,195

4,684,413

4,694,313

4,717,679

4,743,952

4,783,690

4,794,432

4,801,986

4,803,533

4,809,045

4,809,047

4,810,665

4,823,176

4,837,606

4,860,080

4,883,767

4,888,627

4,890,143

4,901,127

4,904,609

4,933,740

4,963,951

4,969,027

CAUTION: These devices are sensitive to electrostatic discharge; follow proper ESD Handling Procedures.

1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000

Page 2

Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified HGTG30N60B3 UNITS Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BVCES 600 V Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25 60 A At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110 30 A Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM 220 A Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGES ±20 V Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM ±30 V Switching Safe Operating Area at TJ = 150oC (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . SSOA 60A at 600V Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 208 W Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.67 W/oC Reverse Voltage Avalanche Energy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EARV 100 mJ Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG -55 to 150 oC Maximum Lead Temperature for Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 260 oC Short Circuit Withstand Time (Note 2) at VGE = 12V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC 4 µs Short Circuit Withstand Time (Note 2) at VGE = 10V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC 10 µs CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Pulse width limited by maximum junction temperature. 2. VCE(PK) = 360V, TJ = 125oC, RG = 3Ω.
Electrical Specifications TC = 25oC, Unless Otherwise Specified
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Collector to Emitter Breakdown Voltage BVCES IC = 250µA, VGE = 0V 600 - - V
Emitter to Collector Breakdown Voltage BVECS IC = 10mA, VGE = 0V 15 28 - V
Collector to Emitter Leakage Current ICES VCE = BVCES TC = 25oC - - 250 µA
TC = 150oC - - 3.0 mA
Collector to Emitter Saturation Voltage VCE(SAT) IC = IC110, VGE = 15V TC = 25oC - 1.45 1.9 V
TC = 150oC - 1.7 2.1 V
Gate to Emitter Threshold Voltage VGE(TH) IC = 250µA, VCE = VGE 4.5 5.0 6.0 V
Gate to Emitter Leakage Current IGES VGE = ±20V - - ±250 nA
Switching SOA SSOA TJ = 150oC, RG = 3Ω, VGE = 15V L = 100µH, VCE (PK) = 480V 200 - - A
VCE (PK) = 600V 60 - - A
Gate to Emitter Plateau Voltage VGEP IC = IC110, VCE = 0.5 BVCES - 7.2 - V
On-State Gate Charge QG(ON) IC = IC110, VCE = 0.5 BVCES VGE = 15V - 170 190 nC
VGE = 20V - 230 250 nC
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 25oC ICE = IC110 VCE = 0.8 BVCES VGE = 15V RG= 3Ω L = 1mH Test Circuit (Figure 17) - 36 - ns
Current Rise Time trI - 25 - ns
Current Turn-Off Delay Time td(OFF)I - 137 - ns
Current Fall Time tfI - 58 - ns
Turn-On Energy (Note 4) EON1 - 500 - µJ
Turn-On Energy (Note 4) EON2 - 550 800 µJ
Turn-Off Energy (Note 3) EOFF - 680 900 µJ

Page 3

Electrical Specifications TC = 25oC, Unless Otherwise Specified (Continued)
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 150oC ICE = IC110 VCE = 0.8 BVCES VGE = 15V RG= 3Ω L = 1mH Test Circuit (Figure 17) - 32 - ns
Current Rise Time trI - 24 - ns
Current Turn-Off Delay Time td(OFF)I - 275 320 ns
Current Fall Time tfI - 90 150 ns
Turn-On Energy (Note 4) EON1 - 500 - µJ
Turn-On Energy (Note 4) EON2 - 1300 1550 µJ
Turn-Off Energy (Note 3) EOFF - 1600 1900 µJ
Thermal Resistance Junction To Case RθJC - - 0.6 oC/W
NOTES: 3. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss. 4. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 17. Typical Performance Curves Unless Otherwise Specified 60 (A) VGE = 15V 225 TJ = 150oC, RG = 3Ω, VGE = 15V, L =100µH (A) CURRENT 200 50 CURRENT 175 40 EMITTER 150 COLLECTOR 125 30 100 TO 20 COLLECTOR 75 DC 50 10 ICE, 25 0 0 ICE, 25 50 75 100 125 150 0 100 200 300 400 500 600 700 TC, CASE TEMPERATURE (oC) VCE, COLLECTOR TO EMITTER VOLTAGE (V) FIGURE 1. DC COLLECTOR CURRENT vs CASE FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA TEMPERATURE 100 TJ = 150oC, RG = 3 VΩ C, L = 1 8m 0VH, 20 VCE = 360V, RG = 3Ω, TJ = 125oC 500 (kHz) (µs) (A) E = 4 TIME CURRENT 18 450 FREQUENCY WITHSTAND 16 400 10 ISC CIRCUIT 14 350 OPERATING 12 300 CIRCUIT SHORT fMAX1 = 0.05 / (td(OFF)I + td(ON)I) TC VGE 1 PfM CA =X 2 O= N(P DD - P TC IO) / ( E DO ISN S2 P+ E TO IOFF N) 7 15 0o ooC 11 55 VV 10 250 C U C N I A 7 5 CC 1 0 V tSC SHORT PEAK 1 fMAX, (DUTY FACTOR = 50%) 110oC 10V 8 200 RØJC = 0.6oC/W, SEE NOTES ISC, 0.1 6 150 tSC, 5 10 20 40 60 10 11 12 13 14 15 ICE, COLLECTOR TO EMITTER CURRENT (A) VGE, GATE TO EMITTER VOLTAGE (V) FIGURE 3. OPERATING FREQUENCY vs COLLECTOR TO FIGURE 4. SHORT CIRCUIT WITHSTAND TIME EMITTER CURRENT

Page 4

PDF page 4 diagram

Page 5

PDF page 5 diagram

Page 6

PDF page 6 diagram

Page 7

Handling Precautions for IGBTs

Insulated Gate Bipolar Transistors are susceptible to gateinsulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:

  1. Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are

essentially capacitors. Circuits that leave the gate open-circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.

Operating Frequency Information

Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.

fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 18. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.

fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON2). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON2 and EOFF are defined in the switching waveforms shown in Figure 18. EON2 is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).

All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see web site www.intersil.com

ECCOSORBD™ is a trademark of Emerson and Cumming, Inc.