HGTG18N120BND INTERSIL

Document overview

  • PDF pages: 7

Technical content

Page 1

Data Sheet

54A, 1200V, NPT Series N-Channel IGBT

with Anti-Parallel Hyperfast Diode

The HGTG18N120BND is a Non-Punch Through (NPT) IGBT design. This is a new member of the MOS gated high voltage switching IGBT family. IGBTs combine the best features of MOSFETs and bipolar transistors. This device has the high input impedance of a MOSFET and the low on- state conduction loss of a bipolar transistor.

The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.

Formerly Developmental Type TA49304.

Ordering Information

PART NUMBER PACKAGE BRAND
HGTG18N120BND TO-247 18N120BND

NOTE: When ordering, use the entire part number.

Symbol

G

E

January 2000

File Number 4555.1

Features

  • 54A, 1200V, TC = 25oC
  • 1200V Switching SOA Capability
  • Typical Fall Time. . . . . . . . . . . . . . . . 140ns at TJ = 150oC
  • Short Circuit Rating
  • Low Conduction Loss

Packaging

JEDEC STYLE TO-247

INTERSIL CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,364,073

4,417,385

4,430,792

4,443,931

4,466,176

4,516,143

4,532,534

4,587,713

4,598,461

4,605,948

4,620,211

4,631,564

4,639,754

4,639,762

4,641,162

4,644,637

4,682,195

4,684,413

4,694,313

4,717,679

4,743,952

4,783,690

4,794,432

4,801,986

4,803,533

4,809,045

4,809,047

4,810,665

4,823,176

4,837,606

4,860,080

4,883,767

4,888,627

4,890,143

4,901,127

4,904,609

4,933,740

4,963,951

4,969,027

CAUTION: These devices are sensitive to electrostatic discharge; follow proper ESD Handling Procedures.

1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000

Page 2

Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified HGTG18N120BND UNITS Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BVCES 1200 V Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25 54 A At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110 26 A Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM 160 A Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGES ±20 V Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM ±30 V Switching Safe Operating Area at TJ = 150oC (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . SSOA 100A at 1200V Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 390 W Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.12 W/oC Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG -55 to 150 oC Maximum Lead Temperature for Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 260 oC Short Circuit Withstand Time (Note 2) at VGE = 15V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC 8 µs Short Circuit Withstand Time (Note 2) at VGE = 12V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC 15 µs CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Pulse width limited by maximum junction temperature. 2. VCE(PK) = 960V, TJ = 125oC, RG = 3Ω.
Electrical Specifications TC = 25oC, Unless Otherwise Specified
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Collector to Emitter Breakdown Voltage BVCES IC = 250µA, VGE = 0V 1200 - - V
Emitter to Collector Breakdown Voltage BVECS IC = 10mA, VGE = 0V 15 - - V
Collector to Emitter Leakage Current ICES VCE = BVCES TC = 25oC - - 250 µA
TC = 125oC - 300 - µA
TC = 150oC - - 4 mA
Collector to Emitter Saturation Voltage VCE(SAT) IC = 18A, VGE = 15V TC = 25oC - 2.45 2.7 V
TC = 150oC - 3.8 4.2 V
Gate to Emitter Threshold Voltage VGE(TH) IC = 150µA, VCE = VGE 6.0 7.0 - V
Gate to Emitter Leakage Current IGES VGE = ±20V - - ±250 nA
Switching SOA SSOA TJ = 150oC, RG = 3Ω, VGE = 15V, L = 200µH, VCE(PK) = 1200V 100 - - A
Gate to Emitter Plateau Voltage VGEP IC = 18A, VCE = 0.5 BVCES - 10.5 - V
On-State Gate Charge QG(ON) IC = 18A, VCE = 0.5 BVCES VGE = 15V - 165 200 nC
VGE = 20V - 220 250 nC
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 25oC ICE = 18A VCE = 0.8 BVCES VGE = 15V RG = 3Ω L = 1mH Test Circuit (Figure 20) - 23 28 ns
Current Rise Time trI - 17 22 ns
Current Turn-Off Delay Time td(OFF)I - 170 200 ns
Current Fall Time tfI - 90 140 ns
Turn-On Energy EON - 1.9 2.4 mJ
Turn-Off Energy (Note 3) EOFF - 1.8 2.2 mJ

Page 3

Electrical Specifications TC = 25oC, Unless Otherwise Specified (Continued)
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 150oC ICE = 18A VCE = 0.8 BVCES VGE = 15V RG = 3Ω L = 1mH Test Circuit (Figure 20) - 21 26 ns
Current Rise Time trI - 17 22 ns
Current Turn-Off Delay Time td(OFF)I - 205 240 ns
Current Fall Time tfI - 140 200 ns
Turn-On Energy EON - 3.7 4.9 mJ
Turn-Off Energy (Note 3) EOFF - 2.6 3.1 mJ
Diode Forward Voltage VEC IEC = 18A - 2.6 3.2 V
Diode Reverse Recovery Time trr IEC = 18A, dIEC/dt = 200A/µs - 60 75 ns
IEC = 2A, dIEC/dt = 200A/µs - 44 55 ns
Thermal Resistance Junction To Case RθJC IGBT - - 0.32 oC/W
Diode - - 0.75 oC/W
NOTE: 3. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss. Typical Performance Curves Unless Otherwise Specified 60 120 (A) VGE = 15V TJ = 150oC, RG = 3Ω, VGE = 15V, L = 200µH (A) CURRENT 50 100 CURRENT 40 80 EMITTER COLLECTOR 30 60 TO 20 40 COLLECTOR DC 10 20 ICE, 0 0 ICE, 25 50 75 100 125 150 0 200 400 600 800 1000 1200 1400 TC, CASE TEMPERATURE (oC) VCE, COLLECTOR TO EMITTER VOLTAGE (V) FIGURE 1. DC COLLECTOR CURRENT vs CASE FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA TEMPERATURE
PDF page 3 diagram

Page 4

PDF page 4 diagram

Page 5

PDF page 5 diagram

Page 6

PDF page 6 diagram

Page 7

Test Circuits and Waveforms

L = 1mH

RG = 3Ω

+

VDD = 960V

-

FIGURE 20. INDUCTIVE SWITCHING TEST CIRCUIT

Handling Precautions for IGBTs

Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken: 1. Prior to assembly into a circuit, all leads should be kept

shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are essentially capacitors. Circuits that leave the gate

open-circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.

90%

10%

VGE

EON

EOFF

VCE

90%

10%

ICE

td(OFF)I

trI

tfI

td(ON)I

FIGURE 21. SWITCHING TEST WAVEFORMS

Operating Frequency Information

Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.

fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 21. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.

fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON and EOFF are defined in the switching waveforms shown in Figure 21. EON is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).

All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see web site www.intersil.com

ECCOSORBD is a Trademark of Emerson and Cumming, Inc.