HGTG18N120BND_07 FAIRCHILD
Document overview
- PDF pages: 8
Technical content
Page 1
Data Sheet March 2007
54A, 1200V, NPT Series N-Channel IGBT
with Anti-Parallel Hyperfast Diode
The HGTG18N120BND is a Non-Punch Through (NPT) IGBT design. This is a new member of the MOS gated high voltage switching IGBT family. IGBTs combine the best features of MOSFETs and bipolar transistors. This device has the high input impedance of a MOSFET and the low on- state conduction loss of a bipolar transistor.
The IGBT is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.
Formerly Developmental Type TA49304.
Ordering Information
| PART NUMBER | PACKAGE | BRAND |
|---|---|---|
| HGTG18N120BND | TO-247 | 18N120BND |
NOTE: When ordering, use the entire part number.
Symbol
C
G
E
Features
- 54A, 1200V, TC = 25oC
- 1200V Switching SOA Capability
- Typical Fall Time . . . . . . . . . . . . . . . 140ns at TJ = 150oC
- Short Circuit Rating
- Low Conduction Loss
Packaging
JEDEC STYLE TO-247

FAIRCHILD SEMICONDUCTOR IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS
4,364,073
4,417,385
4,430,792
4,443,931
4,466,176
4,516,143
4,532,534
4,587,713
4,598,461
4,605,948
4,620,211
4,631,564
4,639,754
4,639,762
4,641,162
4,644,637
4,682,195
4,684,413
4,694,313
4,717,679
4,743,952
4,783,690
4,794,432
4,801,986
4,803,533
4,809,045
4,809,047
4,810,665
4,823,176
4,837,606
4,860,080
4,883,767
4,888,627
4,890,143
4,901,127
4,904,609
4,933,740
4,963,951
4,969,027
Page 2
Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified
UNITS
1200
V
Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BVCES Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25
54
A
At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110
26
A
160
A
Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM
±20
V
Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGES
±30
V
Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGEM Switching Safe Operating Area at TJ = 150oC (Figure 2) . . . . . . . . . . . . . . . . . . . . . . . SSOA
100A at 1200V
Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD
390
W
Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W/oC
3.12
oC
Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG
-55 to 150
oC
260
Maximum Lead Temperature for Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL Short Circuit Withstand Time (Note 2) at VGE = 15V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC
8
µs
Short Circuit Withstand Time (Note 2) at VGE = 12V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .tSC
15
µs
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES: 1. Pulse width limited by maximum junction temperature. 2. VCE(PK) = 960V, TJ = 125oC, RG = 3Ω.
Electrical Specifications TC = 25oC, Unless Otherwise Specified
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS | |
|---|---|---|---|---|---|---|---|
| Collector to Emitter Breakdown Voltage | BVCES | IC = 250µA, VGE = 0V | 1200 | - | - | V | |
| Emitter to Collector Breakdown Voltage | BVECS | IC = 10mA, VGE = 0V | 15 | - | - | V | |
| Collector to Emitter Leakage Current | ICES | VCE = 1200V | TC = 25oC | - | - | 250 | µA |
| TC = 125oC | - | 300 | - | µA | |||
| TC = 150oC | - | - | 4 | mA | |||
| Collector to Emitter Saturation Voltage | VCE(SAT) | IC = 18A, VGE = 15V | TC = 25oC | - | 2.45 | 2.7 | V |
| TC = 150oC | - | 3.8 | 4.2 | V | |||
| Gate to Emitter Threshold Voltage | VGE(TH) | IC = 150µA, VCE = VGE | 6.0 | 7.0 | - | V | |
| Gate to Emitter Leakage Current | IGES | VGE = ±20V | - | - | ±250 | nA | |
| Switching SOA | SSOA | TJ = 150oC, RG = 3Ω, VGE = 15V, L = 200µH, VCE(PK) = 1200V | 100 | - | - | A | |
| Gate to Emitter Plateau Voltage | VGEP | IC = 18A, VCE = 600V | - | 10.5 | - | V | |
| On-State Gate Charge | QG(ON) | IC = 18A, VCE = 600V | VGE = 15V | - | 165 | 200 | nC |
| VGE = 20V | - | 220 | 250 | nC | |||
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode at TJ = 25oC ICE = 18A VCE = 960V VGE = 15V RG = 3Ω L = 1mH Test Circuit (Figure 20) | - | 23 | 28 | ns | |
| Current Rise Time | trI | - | 17 | 22 | ns | ||
| Current Turn-Off Delay Time | td(OFF)I | - | 170 | 200 | ns | ||
| Current Fall Time | tfI | - | 90 | 140 | ns | ||
| Turn-On Energy | EON | - | 1.9 | 2.4 | mJ | ||
| Turn-Off Energy (Note 3) | EOFF | - | 1.8 | 2.2 | mJ | ||
HGTG18N120BND Rev. C
Page 3
Electrical Specifications TC = 25oC, Unless Otherwise Specified (Continued)
| PARAMETER | SYMBOL | TEST CONDITIONS | MIN | TYP | MAX | UNITS |
|---|---|---|---|---|---|---|
| Current Turn-On Delay Time | td(ON)I | IGBT and Diode at TJ = 150oC ICE = 18A VCE = 960V VGE = 15V RG = 3Ω L = 1mH Test Circuit (Figure 20) | - | 21 | 26 | ns |
| Current Rise Time | trI | - | 17 | 22 | ns | |
| Current Turn-Off Delay Time | td(OFF)I | - | 205 | 240 | ns | |
| Current Fall Time | tfI | - | 140 | 200 | ns | |
| Turn-On Energy | EON | - | 3.7 | 4.9 | mJ | |
| Turn-Off Energy (Note 3) | EOFF | - | 2.6 | 3.1 | mJ | |
| Diode Forward Voltage | VEC | IEC = 18A | - | 2.6 | 3.2 | V |
| Diode Reverse Recovery Time | trr | IEC = 18A, dIEC/dt = 200A/µs | - | 60 | 75 | ns |
| IEC = 2A, dIEC/dt = 200A/µs | - | 44 | 55 | ns | ||
| Thermal Resistance Junction To Case | RθJC | IGBT | - | - | 0.32 | oC/W |
| Diode | - | - | 0.75 | oC/W |
NOTE: 3. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss.
Typical Performance Curves Unless Otherwise Specified

50 25
75 100 125 150
TC, CASE TEMPERATURE (oC)
FIGURE 1. DC COLLECTOR CURRENT vs CASE
TEMPERATURE

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA
Page 4
Typical Performance Curves Unless Otherwise Specified (Continued)


12
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 3. OPERATING FREQUENCY vs COLLECTOR TO
EMITTER CURRENT
13 14 15 16
VGE, GATE TO EMITTER VOLTAGE (V)
FIGURE 4. SHORT CIRCUIT WITHSTAND TIME


VCE, COLLECTOR TO EMITTER VOLTAGE (V)
VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 6. COLLECTOR TO EMITTER ON-STATE VOLTAGE
FIGURE 5. COLLECTOR TO EMITTER ON-STATE VOLTAGE


5 10 15
25 30 35 40
ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 8. TURN-OFF ENERGY LOSS vs COLLECTOR TO
FIGURE 7. TURN-ON ENERGY LOSS vs COLLECTOR TO
EMITTER CURRENT
EMITTER CURRENT
Page 5
Typical Performance Curves Unless Otherwise Specified (Continued)


ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 10. TURN-ON RISE TIME vs COLLECTOR TO
FIGURE 9. TURN-ON DELAY TIME vs COLLECTOR TO
EMITTER CURRENT
EMITTER CURRENT


15 20
30 35 40
5 10
25
ICE, COLLECTOR TO EMITTER CURRENT (A)
ICE, COLLECTOR TO EMITTER CURRENT (A)
FIGURE 12. FALL TIME vs COLLECTOR TO EMITTER
FIGURE 11. TURN-OFF DELAY TIME vs COLLECTOR TO
EMITTER CURRENT
CURRENT


VGE, GATE TO EMITTER VOLTAGE (V)
QG, GATE CHARGE (nC)
FIGURE 13. TRANSFER CHARACTERISTIC
FIGURE 14. GATE CHARGE WAVEFORMS
Page 6
Typical Performance Curves Unless Otherwise Specified (Continued)

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 15. CAPACITANCE vs COLLECTOR TO EMITTER
VOLTAGE

VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 16. COLLECTOR TO EMITTER ON-STATE VOLTAGE

t1, RECTANGULAR PULSE DURATION (s)
FIGURE 17. NORMALIZED TRANSIENT THERMAL RESPONSE, JUNCTION TO CASE

VF, FORWARD VOLTAGE (V)
FIGURE 18. DIODE FORWARD CURRENT vs FORWARD
VOLTAGE DROP

IF, FORWARD CURRENT (A)
FIGURE 19. RECOVERY TIMES vs FORWARD CURRENT
Page 7
Test Circuits and Waveforms

VDD = 960V
FIGURE 20. INDUCTIVE SWITCHING TEST CIRCUIT
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken: 1. Prior to assembly into a circuit, all leads should be kept
shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are essentially capacitors. Circuits that leave the gate
open-circuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.
| 90% 10% | ||
| EO EOFF 90% 10% td(OFF)I tfI | N trI td(ON)I | |
VGE
VCE
ICE
FIGURE 21. SWITCHING TEST WAVEFORMS
Operating Frequency Information
Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.
fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 21. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.
fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON and EOFF are defined in the switching waveforms shown in Figure 21. EON is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).
Page 8
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx®
HiSeC™
Across the board. Around the world.™ i-Lo™ ActiveArray™
ImpliedDisconnect™
Bottomless™
IntelliMAX™
Build it Now™
ISOPLANAR™
CoolFET™
MICROCOUPLER™
CROSSVOLT™
MicroPak™
CTL™
MICROWIRE™
Current Transfer Logic™
MSX™
DOME™
MSXPro™
E2CMOS™
OCX™
EcoSPARK®
OCXPro™
EnSigna™
OPTOLOGIC®
FACT Quiet Series™
OPTOPLANAR®
FACT®
PACMAN™
FAST®
POP™
FASTr™
Power220®
FPS™
Power247®
FRFET®
PowerEdge™
GlobalOptoisolator™
PowerSaver™
GTO™
PowerTrench®
DISCLAIMER
Programmable Active Droop™ TinyLogic® QFET®
TINYOPTO™
QS™
TinyPower™
QT Optoelectronics™
TinyWire™
Quiet Series™
TruTranslation™
RapidConfigure™
μSerDes™ UHC®
RapidConnect™
UniFET™
ScalarPump™
VCX™
SMART START™ SPM®
Wire™
STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TCM™
®
The Power Franchise ™ TinyBoost™ TinyBuck™
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user.
PRODUCT STATUS DEFINITIONS
Definition of Terms
- A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
| Datasheet Identification | Product Status | Definition |
| Advance Information | Formative or In Design | This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. |
| Preliminary | First Production | This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. |
| No Identification Needed | Full Production | This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. |
| Obsolete | Not In Production | This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. |
Rev. I24
© 2007 Fairchild Semiconductor Corporation
www.fairchildsemi.com