HGTG12N60A4D INTERSIL

Document overview

  • PDF pages: 8

Technical content

Page 1

Data Sheet

600V, SMPS Series N-Channel IGBT with

Anti-Parallel Hyperfast Diode

The HGTG12N60A4D, HGTP12N60A4D and HGT1S12N60A4DS are MOS gated high voltage switching devices combining the best features of MOSFETs and bipolar transistors. These devices have the high input impedance of a MOSFET and the low on-state conduction loss of a bipolar transistor. The much lower on-state voltage drop varies only moderately between 25oC and 150oC. The IGBT used is the development type TA49335. The diode used in anti-parallel is the development type TA49371.

This IGBT is ideal for many high voltage switching applications operating at high frequencies where low conduction losses are essential. This device has been optimized for high frequency switch mode power supplies.

Formerly Developmental Type TA49337.

Ordering Information

PART NUMBER PACKAGE BRAND
HGTG12N60A4D TO-247 12N60A4D
HGTP12N60A4D TO-220AB 12N60A4D
HGT1S12N60A4DS TO-263AB 12N60A4D

NOTE: When ordering, use the entire part number. Add the suffix 9A to obtain the TO-263AB variant in tape and reel, e.g. HGT1S12N60A4DS9A.

Symbol

C

G

E

HGTG12N60A4D, HGTP12N60A4D,

HGT1S12N60A4DS

November 1999

File Number 4697.3

Features

  • >100kHz Operation . . . . . . . . . . . . . . . . . . . . . 390V, 12A
  • 200kHz Operation . . . . . . . . . . . . . . . . . . . . . . . 390V, 9A
  • 600V Switching SOA Capability
  • Typical Fall Time. . . . . . . . . . . . . . . . . 70ns at TJ = 125oC
  • Low Conduction Loss
  • Temperature Compensating SABER™ Model www.intersil.com
  • Related Literature - TB334 “Guidelines for Soldering Surface Mount Components to PC Boards

Packaging

JEDEC TO-220AB ALTERNATE VERSION

E C G

COLLECTOR

(FLANGE)

JEDEC TO-263AB

COLLECTOR

(FLANGE)

G E

JEDEC STYLE TO-247

E C G

COLLECTOR

(FLANGE)

INTERSIL CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,364,073

4,417,385

4,430,792

4,443,931

4,466,176

4,516,143

4,532,534

4,587,713

4,598,461

4,605,948

4,620,211

4,631,564

4,639,754

4,639,762

4,641,162

4,644,637

4,682,195

4,684,413

4,694,313

4,717,679

4,743,952

4,783,690

4,794,432

4,801,986

4,803,533

4,809,045

4,809,047

4,810,665

4,823,176

4,837,606

4,860,080

4,883,767

4,888,627

4,890,143

4,901,127

4,904,609

4,933,740

4,963,951

4,969,027

CAUTION: These devices are sensitive to electrostatic discharge; follow proper ESD Handling Procedures.

2-1

SABER™ is a trademark of Analogy, Inc.

1-888-INTERSIL or 407-727-9207 | Copyright © Intersil Corporation 1999

Page 2

Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified HGTG12N60A4D, HGTP12N60A4D, HGT1S12N60A4DS UNITS Collector to Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BVCES 600 V Collector Current Continuous At TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC25 54 A At TC = 110oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC110 23 A Collector Current Pulsed (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICM 96 A Gate to Emitter Voltage Continuous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGES ±20 V Gate to Emitter Voltage Pulsed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGEM ±30 V Switching Safe Operating Area at TJ = 150oC, Figure 2 . . . . . . . . . . . . . . . . . . . . . . . . SSOA 60A at 600V Power Dissipation Total at TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 167 W Power Dissipation Derating TC > 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33 W/oC Operating and Storage Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG -55 to 150 oC Maximum Temperature for Soldering Leads at 0.063in (1.6mm) from Case for 10s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 300 oC Package Body for 10s, see Tech Brief 334. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tpkg 260 oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. Pulse width limited by maximum junction temperature.
Electrical Specifications TJ = 25oC, Unless Otherwise Specified
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Collector to Emitter Breakdown Voltage BVCES IC = 250µA, VGE = 0V 600 - - V
Collector to Emitter Leakage Current ICES VCE = 600V TJ = 25oC - - 250 µA
TJ = 125oC - - 2.0 mA
Collector to Emitter Saturation Voltage VCE(SAT) IC = 12A, VGE = 15V TJ = 25oC - 2.0 2.7 V
TJ = 125oC - 1.6 2.0 V
Gate to Emitter Threshold Voltage VGE(TH) IC = 250µA, VCE = 600V - 5.6 - V
Gate to Emitter Leakage Current IGES VGE = ±20V - - ±250 nA
Switching SOA SSOA TJ = 150oC, RG = 10Ω, VGE = 15V, L = 100µH, VCE = 600V 60 - - A
Gate to Emitter Plateau Voltage VGEP IC = 12A, VCE = 300V - 8 - V
On-State Gate Charge Qg(ON) IC = 12A, VCE = 300V VGE = 15V - 78 96 nC
VGE = 20V - 97 120 nC
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 25oC, ICE = 12A, VCE = 390V, VGE = 15V, RG = 10Ω, L = 500µH, Test Circuit (Figure 24) - 17 - ns
Current Rise Time trI - 8 - ns
Current Turn-Off Delay Time td(OFF)I - 96 - ns
Current Fall Time tfI - 18 - ns
Turn-On Energy (Note 3) EON1 - 55 - µJ
Turn-On Energy (Note 3) EON2 - 160 - µJ
Turn-Off Energy (Note 2) EOFF - 50 - µJ
Current Turn-On Delay Time td(ON)I IGBT and Diode at TJ = 125oC, ICE = 12A, VCE = 390V, VGE = 15V, RG = 10Ω, L = 500µH, Test Circuit (Figure 24) - 17 - ns
Current Rise Time trI - 16 - ns
Current Turn-Off Delay Time td(OFF)I - 110 170 ns
Current Fall Time tfI - 70 95 ns
Turn-On Energy (Note3) EON1 - 55 - µJ
Turn-On Energy (Note 3) EON2 - 250 350 µJ
Turn-Off Energy (Note 2) EOFF - 175 285 µJ

2-2

Page 3

Electrical Specifications TJ = 25oC, Unless Otherwise Specified (Continued)
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Diode Forward Voltage VEC IEC = 12A - 2.2 - V
Diode Reverse Recovery Time trr IEC = 12A, dIEC/dt = 200A/µs - 30 - ns
IEC = 1A, dIEC/dt = 200A/µs - 18 - ns
Thermal Resistance Junction To Case RθJC IGBT - - 0.75 oC/W
Diode - - 2.0 oC/W
NOTES: 2. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss. 3. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 24. Typical Performance Curves Unless Otherwise Specified (A) 60 VGE = 15V, 70 TJ = 150oC, RG = 10Ω, VGE = 15V, L = 200µH CURRENT (A) 60 50 CURRENT 50 EMITTER 40 40 COLLECTOR 30 30 TO COLLECTOR 20 20 DC 10 10 ICE, 0 0 ICE, 25 50 75 100 125 150 0 100 200 300 400 500 600 700 TC, CASE TEMPERATURE (oC) VCE, COLLECTOR TO EMITTER VOLTAGE (V) FIGURE 1. DC COLLECTOR CURRENT vs CASE FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA TEMPERATURE 500 20 300 (µs) (A) VCE = 390V, RG = 10Ω, TJ = 125oC 300 TC VGE 18 275 (kHz) TIME CURRENT 75oC 15V 16 250 FREQUENCY WITHSTAND 14 225 ISC CIRCUIT 100 12 200 fMAX1 = 0.05 / (td(OFF)I + td(ON)I) fMAX2 = (PD - PC) / (EON2 + EOFF) 10 175 PC = CONDUCTION DISSIPATION 8 150 OPERATING CIRCUIT SHORT (DUTY FACTOR = 50%) RØJC = 0.75oC/W, SEE NOTES 6 tSC 125 4 100 SHORT PEAK TJ = 125oC, RG = 10Ω, L = 500µH, VCE = 390V 2 75 fMAX, ISC, tSC, 10 0 50 1 3 10 20 30 9 10 11 12 13 14 15 ICE, COLLECTOR TO EMITTER CURRENT (A) VGE, GATE TO EMITTER VOLTAGE (V) FIGURE 3. OPERATING FREQUENCY vs COLLECTOR TO FIGURE 4. SHORT CIRCUIT WITHSTAND TIME EMITTER CURRENT

2-3

Page 4

PDF page 4 diagram

Page 5

PDF page 5 diagram

Page 6

PDF page 6 diagram

Page 7

PDF page 7 diagram

Page 8

Handling Precautions for IGBTs

Insulated Gate Bipolar Transistors are susceptible to gate-insulation damage by the electrostatic discharge of energy through the devices. When handling these devices, care should be exercised to assure that the static charge built in the handler’s body capacitance is not discharged through the device. With proper handling and application procedures, however, IGBTs are currently being extensively used in production by numerous equipment manufacturers in military, industrial and consumer applications, with virtually no damage problems due to electrostatic discharge. IGBTs can be handled safely if the following basic precautions are taken:

  1. Prior to assembly into a circuit, all leads should be kept shorted together either by the use of metal shorting springs or by the insertion into conductive material such as “ECCOSORBD™ LD26” or equivalent. 2. When devices are removed by hand from their carriers, the hand being used should be grounded by any suitable means - for example, with a metallic wristband. 3. Tips of soldering irons should be grounded. 4. Devices should never be inserted into or removed from circuits with power on. 5. Gate Voltage Rating - Never exceed the gate-voltage rating of VGEM. Exceeding the rated VGE can result in permanent damage to the oxide layer in the gate region. 6. Gate Termination - The gates of these devices are

essentially capacitors. Circuits that leave the gate opencircuited or floating should be avoided. These conditions can result in turn-on of the device due to voltage buildup on the input capacitor due to leakage currents or pickup. 7. Gate Protection - These devices do not have an internal monolithic Zener diode from gate to emitter. If gate protection is required an external Zener is recommended.

2-8

Operating Frequency Information

Operating frequency information for a typical device (Figure 3) is presented as a guide for estimating device performance for a specific application. Other typical frequency vs collector current (ICE) plots are possible using the information shown for a typical unit in Figures 5, 6, 7, 8, 9 and 11. The operating frequency plot (Figure 3) of a typical device shows fMAX1 or fMAX2; whichever is smaller at each point. The information is based on measurements of a typical device and is bounded by the maximum rated junction temperature.

fMAX1 is defined by fMAX1 = 0.05/(td(OFF)I+ td(ON)I). Deadtime (the denominator) has been arbitrarily held to 10% of the on-state time for a 50% duty factor. Other definitions are possible. td(OFF)I and td(ON)I are defined in Figure 25. Device turn-off delay can establish an additional frequency limiting condition for an application other than TJM. td(OFF)I is important when controlling output ripple under a lightly loaded condition.

fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON2). The allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC. The sum of device switching and conduction losses must not exceed PD. A 50% duty factor was used (Figure 3) and the conduction losses (PC) are approximated by PC = (VCE x ICE)/2. EON2 and EOFF are defined in the switching waveforms shown in Figure 25. EON2 is the integral of the instantaneous power loss (ICE x VCE) during turn-on and EOFF is the integral of the instantaneous power loss (ICE x VCE) during turn-off. All tail losses are included in the calculation for EOFF; i.e., the collector current equals zero (ICE = 0).

ECCOSORBD™ is a trademark of Emerson and Cumming, Inc.